On SKL+ the plane WM/BUF_CFG registers are a proper part of each
plane's register set. That means accessing them will cancel any
pending plane update, and we would need a PLANE_SURF register write
to arm the wm/ddb change as well.
To avoid all the problems with that let's just move the wm/ddb
programming into the plane update/disable hooks. Now all plane
registers get written in one (hopefully atomic) operation.
To make that feasible we'll move the plane ddb tracking into
the crtc state. Watermarks were already tracked there.
v2: Rebase due to input CSC
v3: Split out a bunch of junk (Matt)
v4: Add skl_wm_add_affected_planes() to deal with
cursor special case and non-zero wm register reset value
v5: Drop the unrelated for_each_intel_plane_mask() fix (Matt)
Remove the redundant ddb memset() (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #v3
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127165900.31298-1-ville.syrjala@linux.intel.com
I have a Thinkpad X220 Tablet in my hands that is losing vblank
interrupts whenever LP3 watermarks are used.
If I nudge the latency value written to the WM3 register just
by one in either direction the problem disappears. That to me
suggests that the punit will not enter the corrsponding
powersave mode (MPLL shutdown IIRC) unless the latency value
in the register matches exactly what we read from SSKPD. Ie.
it's not really a latency value but rather just a cookie
by which the punit can identify the desired power saving state.
On HSW/BDW this was changed such that we actually just write
the WM level number into those bits, which makes much more
sense given the observed behaviour.
We could try to handle this by disallowing LP3 watermarks
only when vblank interrupts are enabled but we'd first have
to prove that only vblank interrupts are affected, which
seems unlikely. Also we can't grab the wm mutex from the
vblank enable/disable hooks because those are called with
various spinlocks held. Thus we'd have to redesigne the
watermark locking. So to play it safe and keep the code
simple we simply disable LP3 watermarks on all SNB machines.
To do that we simply zero out the latency values for
watermark level 3, and we adjust the watermark computation
to check for that. The behaviour now matches that of the
g4x/vlv/skl wm code in the presence of a zeroed latency
value.
v2: s/USHRT_MAX/U32_MAX/ for consistency with the types (Chris)
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101269
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103713
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114173440.6730-1-ville.syrjala@linux.intel.com
Skylake style watermarks program the UV parameters into wm->uv_wm,
and have a separate DDB allocation for UV blocks into the same plane.
Gen11 watermarks have a separate plane for Y and UV, with separate
mechanisms. The simplest way to make it work is to keep the current
way of programming watermarks and calculate the Y and UV plane
watermarks from the master plane.
Changes since v1:
- Constify crtc_state where possible.
- Make separate paths for planar formats in skl_build_pipe_wm() (Matt)
- Make separate paths for calculating total data rate. (Matt)
- Make sure UV watermarks are unused on gen11+ by adding a WARN. (Matt)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181018115134.9061-5-maarten.lankhorst@linux.intel.com
To make NV12 working on icl, we need to update 2 planes simultaneously.
I've chosen to do this in the CRTC step after plane validation is done,
so we know what planes are (in)visible. The linked Y plane will get
updated in intel_plane_update_planes_on_crtc(), by the call to
update_slave, which gets the master's plane_state as argument.
The link requires both planes for atomic_update to work,
so make sure skl_ddb_add_affected_planes() adds both states.
Changes since v1:
- Introduce icl_is_nv12_y_plane(), instead of hardcoding sprite numbers.
- Put all the state updating login in intel_plane_atomic_check_with_state().
- Clean up changes in intel_plane_atomic_check().
Changes since v2:
- Fix intel_atomic_get_old_plane_state() to actually return old state.
- Move visibility changes to preparation patch.
- Only try to find a Y plane on gen11, earlier platforms only require
a single plane.
Changes since v3:
- Fix checkpatch warning about to_intel_crtc() usage.
- Add affected planes from icl_add_linked_planes() before check_planes(),
it's a cleaner way to do this. (Ville)
Changes since v4:
- Clear plane links in icl_check_nv12_planes() for clarity.
- Only pass crtc_state to icl_check_nv12_planes().
- Use for_each_new_intel_plane_in_state() in icl_check_nv12_planes.
- Rename aux to linked. (Ville)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181022135152.15324-1-maarten.lankhorst@linux.intel.com
[mlankhorst: Change bool slave to u32, to satisfy checkpatch]
[mlankhorst: Add WARN_ON's based on Ville's suggestion]
We don't have proper watermark NV12 support on ICL due to differences
in how it should be implemented. In commit 234059da0f
("drm/i915/icl: NV12 y-plane ddb is not in same plane") we avoided
writing the non-existent PLANE_NV12_BUF_CFG registers but we forgot to
also avoid them on the hardware state readout. While the code is still
not correct, at least now we can avoid unclaimed register error
messages when dealing with RGB formats, which makes CI happier.
Also add some FIXME comments in order to make it even more clear that
there's still work to do.
References: commit 234059da0f ("drm/i915/icl: NV12 y-plane ddb is
not in same plane")
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180801004614.22149-1-paulo.r.zanoni@intel.com
RPS provides a feedback loop where we use the load during the previous
evaluation interval to decide whether to up or down clock the GPU
frequency. Our responsiveness is split into 3 regimes, a high and low
plateau with the intent to keep the gpu clocked high to cover occasional
stalls under high load, and low despite occasional glitches under steady
low load, and inbetween. However, we run into situations like kodi where
we want to stay at low power (video decoding is done efficiently
inside the fixed function HW and doesn't need high clocks even for high
bitrate streams), but just occasionally the pipeline is more complex
than a video decode and we need a smidgen of extra GPU power to present
on time. In the high power regime, we sample at sub frame intervals with
a bias to upclocking, and conversely at low power we sample over a few
frames worth to provide what we consider to be the right levels of
responsiveness respectively. At low power, we more or less expect to be
kicked out to high power at the start of a busy sequence by waitboosting.
Prior to commit e9af4ea2b9 ("drm/i915: Avoid waitboosting on the active
request") whenever we missed the frame or stalled, we would immediate go
full throttle and upclock the GPU to max. But in commit e9af4ea2b9, we
relaxed the waitboosting to only apply if the pipeline was deep to avoid
over-committing resources for a near miss. Sadly though, a near miss is
still a miss, and perceptible as jitter in the frame delivery.
To try and prevent the near miss before having to resort to boosting
after the fact, we use the pageflip queue as an indication that we are
in an "interactive" regime and so should sample the load more frequently
to provide power before the frame misses it vblank. This will make us
more favorable to providing a small power increase (one or two bins) as
required rather than going all the way to maximum and then having to
work back down again. (We still keep the waitboosting mechanism around
just in case a dramatic change in system load requires urgent uplocking,
faster than we can provide in a few evaluation intervals.)
v2: Reduce rps_set_interactive to a boolean parameter to avoid the
confusion of what if they wanted a new power mode after pinning to a
different mode (which to choose?)
v3: Only reprogram RPS while the GT is awake, it will be set when we
wake the GT, and while off warns about being used outside of rpm.
v4: Fix deferred application of interactive mode
v5: s/state/interactive/
v6: Group the mutex with its principle in a substruct
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107111
Fixes: e9af4ea2b9 ("drm/i915: Avoid waitboosting on the active request")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180731132629.3381-1-chris@chris-wilson.co.uk
Inherit workarounds from previous platforms that are still valid for
Icelake.
v2: GEN7_ROW_CHICKEN2 is masked
v3:
- Since it has been fixed already in upstream, removed the TODO
comment about WA_SET_BIT for WaInPlaceDecompressionHang.
- Squashed with this patch:
drm/i915/icl: add icelake_init_clock_gating()
from Paulo Zanoni <paulo.r.zanoni@intel.com>
- Squashed with this patch:
drm/i915/icl: WaForceEnableNonCoherent
from Oscar Mateo <oscar.mateo@intel.com>
- WaPushConstantDereferenceHoldDisable is now Wa_1604370585 and
applies to B0 as well.
- WaPipeControlBefore3DStateSamplePattern WABB was being applied
to ICL incorrectly.
v4:
- Wrap the commit message
- s/dev_priv/p to please checkpatch
v5: Rebased on top of the WA refactoring
v6: Rebased on top of further whitelist registers refactoring (Michel)
v7: Added WaRsForcewakeAddDelayForAck
v8: s/ICL_HDC_CHICKEN0/ICL_HDC_MODE (Mika)
v9:
- C, not lisp (Chris)
- WaIncreaseDefaultTLBEntries is the same for GEN > 9_LP (Tvrtko)
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tomasz Lis <tomasz.lis@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1525814984-20039-2-git-send-email-oscar.mateo@intel.com
ICL has two slices of DBuf, each slice of size 1024 blocks.
We should not always enable slice-2. It should be enabled only if
display total required BW is > 12GBps OR more than 1 pipes are enabled.
Changes since V1:
- typecast total_data_rate to u64 before multiplication to solve any
possible overflow (Rodrigo)
- fix where skl_wm_get_hw_state was memsetting ddb, resulting
enabled_slices to become zero
- Fix the logic of calculating ddb_size
Changes since V2:
- If no-crtc is part of commit required_slices will have value "0",
don't try to disable DBuf slice.
Changes since V3:
- Create a generic helper to enable/disable slice
- don't return early if total_data_rate is 0, it may be cursor only
commit, or atomic modeset without any plane.
Changes since V4:
- Solve checkpatch warnings
- use kernel types u8/u64 instead of uint8_t/uint64_t
Changes since V5:
- Rebase
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180426142517.16643-3-mahesh1.kumar@intel.com
