LSPCON chips can generate YCBCR outputs, if asked nicely :).
In order to generate YCBCR 4:2:0 outputs, a source must:
- send YCBCR 4:4:4 signals to LSPCON
- program color space as 4:2:0 in AVI infoframes
Whereas for YCBCR 4:4:4 outputs, the source must:
- send YCBCR 4:4:4 signals to LSPCON
- program color space as 4:4:4 in AVI infoframes
So for both 4:2:0 as well as 4:4:4 outputs, we are driving the
pipe for YCBCR 4:4:4 output, but AVI infoframe's color space
information indicates LSPCON FW to start scaling down from YCBCR
4:4:4 and generate YCBCR 4:2:0 output. As the scaling is done by
LSPCON device, we need not to reserve a scaler for 4:2:0 outputs.
V2: rebase
V3: Addressed review comments from Ville
- add enum crtc_output_format instead of bool ycbcr420
- use crtc_output_format=4:4:4 for modeset of LSPCON 4:2:0 output
cases in this way we will have YCBCR 4:4:4 framework ready (except
the ABI part)
V4: Added r-b from Maarten (for v3)
Addressed review comments from Ville:
- Do not add a non-atomic state variable to determine lspcon output.
Instead add bool in CRTC state to indicate lspcon based scaling.
V5: Addressed review comments from Ville:
- Change the state bool name from external scaling to something more
relavent.
- Keep the info and adjusted_mode structures const.
- use crtc_state instead of pipe_config.
- Push all the config change into lspcon_ycbcr420_config function.
V6: Rebase, small changes to accommodate changes in patch 2.
V7: Fixed checkpatch warnings for alignment
V8: Rebase
PS: Ignored following warnings to match the current formatting:
drm/i915: Add YCBCR 4:2:0/4:4:4 support for LSPCON
-:53: CHECK:SPACING: spaces preferred around that '<<' (ctx:VxV)
#53: FILE: drivers/gpu/drm/i915/i915_reg.h:8721:
+#define TRANS_MSA_SAMPLING_444 (2<<1)
^
-:54: CHECK:SPACING: spaces preferred around that '<<' (ctx:VxV)
#54: FILE: drivers/gpu/drm/i915/i915_reg.h:8722:
+#define TRANS_MSA_CLRSP_YCBCR (2<<3)
V9: Rebase
V10: Rebase
V11: Rebase
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-8-git-send-email-shashank.sharma@intel.com
In order to pass AVI infoframes to LSPCON devices, a source has to
write them in a vendor recommended method and location.
This patch series:
- adds generic LSPCON infoframe setup functions.
- registers these functions into existing AVI infoframe framework.
- triggers these functions from modeset sequence.
Next patches in the series will add vendor specific code.
V2: Added new parameter to align with new definition of
drm_hdmi_avi_infoframe_quant_range
V3: Added r-b from Maarten (for V2)
Added new parameter output_format in struct lspcon to accommodate
Ville's review comments on last patch of the series
V4: Addressed Ville's review comment
- Do not add output_format in LSPCON state, as its non-atomic. Add
this into CRTC state (added in a later patch).
V5: Rebase
V6: Rebase
V7: Rebase
V8: Rebase
V9: Rebase
V10: Rebase
V11: Accommodated rebasing changes in intel_git_port fptrs (set_infoframes and infoframe_enabled)
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-5-git-send-email-shashank.sharma@intel.com
Switch to using the common DP helpers instead of using our own.
v2: also remove leftover struct intel_dp_desc (Daniel)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Some LSPCON adaptors may return an incorrect LSPCON mode right after
waking from DP Sleep state. This is the case at least for the ParadTech
PS175 adaptor, both when waking because of exiting the DP Sleep to
active state, or due to any other AUX CH transfer. We can determine the
current expected mode based on whether the DPCD area is accessible,
since according to the LSPCON spec this area is only accesible
in PCON mode.
This wait will avoid us trying to change the mode, while the current
expected mode hasn't settled yet and start link training before the
adaptor thinks it's in PCON mode after waking from DP Sleep state.
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479755707-29596-4-git-send-email-imre.deak@intel.com
Some LSPCON adaptors won't properly wake up in response to an AUX
request after the adaptor was placed to a DP Sink Sleep state (via
writing 0x2 to DP_SET_POWER). Based on the DP 1.4 specification 5.2.5,
the sink may place the AUX CH into a low-power state while in Sleep
state, but should wake it up in response to an AUX request within 1-20ms
(answering with AUX defers while waking it up). As opposed to this at
least the ParadTech PS175 adaptor won't fully wake in response to the
first I2C-over-AUX access and will occasionally ignore the offset in I2C
messages. This can result in accessing the DDC register at offset 0
regardless of the specified offset and the LSPCON detection failing.
To fix this do an initial dummy read from the DPCD area. The PS175 will
defer this access until it's fully woken (taking ~150ms) making sure the
following I2C-over-AUX accesses will work correctly.
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=98353
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479755707-29596-2-git-send-email-imre.deak@intel.com
On my APL the LSPCON firmware resumes in PCON mode as opposed to the
expected LS mode. It also appears to be in a state where AUX DPCD reads
will succeed but return garbage recovering only after a few hundreds of
milliseconds. After the recovery time DPCD reads will result in the
correct values and things will continue to work. If I2C over AUX is
attempted during this recovery time (implying an AUX write transaction)
the firmware won't recover and will stay in this broken state.
As a workaround check if the firmware is in PCON state after resume and
if so wait until the correct DPCD values are returned. For this we
compare the branch descriptor with the one we cached during init time.
If the firmware was in the LS state, we skip the w/a and continue as
before.
v2:
- Use the DP descriptor value cached in intel_dp. (Jani)
- Get to intel_dp using container_of(), instead of a cached ptr.
(Shashank)
- Use usleep_range() instead of msleep().
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98353
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477326811-30431-9-git-send-email-imre.deak@intel.com
This patch adds a new file, to accommodate lspcon support
for I915 driver. These functions probe, detect, initialize
and configure an on-board lspcon device during the driver
init time.
Also, this patch adds a small structure for lspcon device,
which will provide the runtime status of the device.
V2: addressed ville's review comments
- Clean the leftover macros from previous patch set
V3: Rebase
V4: addressed ville's review comments
- make internal functions static
- remove lspcon_detect_identifier, make it inline with lspcon_probe
- remove is_lspcon_active function
- remove force check while setting a lspcon mode
V5: Rebase
V6: Pass dev_priv to IS_GEN9 check
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Akashdeep Sharma <akashdeep.sharma@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1476455212-27893-3-git-send-email-shashank.sharma@intel.com
