If FEC is supported, the corresponding
DP_TP_CTL register bits have to be configured.
The driver has to program the FEC_ENABLE in DP_TP_CTL[30] register
and wait till FEC_STATUS in DP_TP_CTL[28] is 1.
Also add the warn message to make sure that the control
register is already active while enabling FEC.
v2:
- Change commit message. Configure fec state after
link training (Manasi, Gaurav)
- Remove redundent checks (Manasi)
- Remove the registers that get added automagically (Anusha)
v3: s/intel_dp_set_fec_state()/intel_dp_enable_fec_state() (Gaurav)
v4: rebased.
v5:
- Move the code to the proper spot, according to spec.(Ville)
- Use fec state as a check too.
v6: Pass intel_encoder, instead of intel_dp. (Ville)
v7: Remove unwanted comments (Manasi)
Cc: dri-devel@lists.freedesktop.org
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-16-manasi.d.navare@intel.com
After encoder->pre_enable() hook, after link training sequence is
completed, PPS registers for DSC encoder are configured using the
DSC state parameters in intel_crtc_state as part of DSC enabling
routine in the source. DSC enabling routine is called after
encoder->pre_enable() before enbaling the pipe and after
compression is enabled on the sink.
v7:
* Remove unnecessary comments, leftovers (Ville)
* No need for explicit val &= ~ (Ville)
v6:
intel_dsc_enable to be part of pre_enable hook (Ville)
v5:
* make crtc_state const (Ville)
v4:
* Use cpu_transcoder instead of encoder->type for using EDP transcoder
DSC registers(Ville)
* Keep all PSS regs together (Anusha)
v3:
* Configure Pic_width/2 for each VDSC engine when two VDSC engines per pipe
are used (Manasi)
* Add DSC slice_row_per_frame in PPS16 (Manasi)
v2:
* Enable PG2 power well for VDSC on eDP
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
[manasi: fixup the line longer than 100 chars while applying]
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-8-manasi.d.navare@intel.com
Depending on the transcoder enum values to translate from transcoder to
the corresponding CHICKEN_TRANS register can easily break if we add a
new transcoder. Add an explicit mapping instead, by using helpers to
look up the register instance either by transcoder or port (since
unconveniently the registers have both port and transcoder specific
bits).
While at it also check for the correctness of GEN, port, transcoder. I
wasn't sure if psr2_enabled can only be set for GEN9+, but that seems to
be the case indeed (see setting of sink_psr2_support in
intel_psr_init_dpcd()).
v2 (Ville):
- Make gen9_chicken_trans_reg() internal to intel_psr.c.
- s/trans/cpu_transcoder/
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181119180021.370-1-imre.deak@intel.com
We shouldn't consider an encoder inactive if it doesn't have a CRTC
linked, but has virtual MST encoders with a crtc linked. Fix this.
Also we should not sanitize the mapping for MST encoders, as it's always
their primary encoder (which could be even in SST mode) whose active
state determines if we need the clock being enabled for the
corresponding physical port. Fix this too.
This fixes at least an existing breakage where we incorrectly disabled
the clock for an active DP encoder when sanitizing its MST virtual
encoders. Not sure if there are BIOSes that enable an output in MST
mode, but our HW readout is mostly missing for it anyway, so just warn
for that case.
Fixes: 70332ac539 ("drm/i915/icl+: Sanitize port to PLL mapping")
Cc: Antonio Argenziano <antonio.argenziano@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reported-by: Antonio Argenziano <antonio.argenziano@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107200836.10191-2-imre.deak@intel.com
LSPCON chips can generate YCBCR outputs, if asked nicely :).
In order to generate YCBCR 4:2:0 outputs, a source must:
- send YCBCR 4:4:4 signals to LSPCON
- program color space as 4:2:0 in AVI infoframes
Whereas for YCBCR 4:4:4 outputs, the source must:
- send YCBCR 4:4:4 signals to LSPCON
- program color space as 4:4:4 in AVI infoframes
So for both 4:2:0 as well as 4:4:4 outputs, we are driving the
pipe for YCBCR 4:4:4 output, but AVI infoframe's color space
information indicates LSPCON FW to start scaling down from YCBCR
4:4:4 and generate YCBCR 4:2:0 output. As the scaling is done by
LSPCON device, we need not to reserve a scaler for 4:2:0 outputs.
V2: rebase
V3: Addressed review comments from Ville
- add enum crtc_output_format instead of bool ycbcr420
- use crtc_output_format=4:4:4 for modeset of LSPCON 4:2:0 output
cases in this way we will have YCBCR 4:4:4 framework ready (except
the ABI part)
V4: Added r-b from Maarten (for v3)
Addressed review comments from Ville:
- Do not add a non-atomic state variable to determine lspcon output.
Instead add bool in CRTC state to indicate lspcon based scaling.
V5: Addressed review comments from Ville:
- Change the state bool name from external scaling to something more
relavent.
- Keep the info and adjusted_mode structures const.
- use crtc_state instead of pipe_config.
- Push all the config change into lspcon_ycbcr420_config function.
V6: Rebase, small changes to accommodate changes in patch 2.
V7: Fixed checkpatch warnings for alignment
V8: Rebase
PS: Ignored following warnings to match the current formatting:
drm/i915: Add YCBCR 4:2:0/4:4:4 support for LSPCON
-:53: CHECK:SPACING: spaces preferred around that '<<' (ctx:VxV)
#53: FILE: drivers/gpu/drm/i915/i915_reg.h:8721:
+#define TRANS_MSA_SAMPLING_444 (2<<1)
^
-:54: CHECK:SPACING: spaces preferred around that '<<' (ctx:VxV)
#54: FILE: drivers/gpu/drm/i915/i915_reg.h:8722:
+#define TRANS_MSA_CLRSP_YCBCR (2<<3)
V9: Rebase
V10: Rebase
V11: Rebase
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-8-git-send-email-shashank.sharma@intel.com
In order to pass AVI infoframes to LSPCON devices, a source has to
write them in a vendor recommended method and location.
This patch series:
- adds generic LSPCON infoframe setup functions.
- registers these functions into existing AVI infoframe framework.
- triggers these functions from modeset sequence.
Next patches in the series will add vendor specific code.
V2: Added new parameter to align with new definition of
drm_hdmi_avi_infoframe_quant_range
V3: Added r-b from Maarten (for V2)
Added new parameter output_format in struct lspcon to accommodate
Ville's review comments on last patch of the series
V4: Addressed Ville's review comment
- Do not add output_format in LSPCON state, as its non-atomic. Add
this into CRTC state (added in a later patch).
V5: Rebase
V6: Rebase
V7: Rebase
V8: Rebase
V9: Rebase
V10: Rebase
V11: Accommodated rebasing changes in intel_git_port fptrs (set_infoframes and infoframe_enabled)
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-5-git-send-email-shashank.sharma@intel.com
Currently, we are using a bool in CRTC state (state->ycbcr420),
to indicate modeset, that the output format is YCBCR 4:2:0. Now in
order to support other YCBCR formats, we will need more such flags.
This patch adds a new enum parameter for YCBCR 4:2:0 outputs, in the
CRTC output formats and then plugs it during the modeset.
V3: Added this patch in the series, to address review comments from
second patchset.
V4: Added r-b from Maarten (on v3)
Addressed review comments from Ville:
- Change the enum name to intel_output_format.
- Start the enum value (INVALID) from 0 instaed of 1.
- Set the crtc's output_format to RGB in encoder's compute_config.
V5: Broke previous patch 1 into two parts,
- first patch to add CRTC output format in general
- second patch (this one) to add YCBCR 4:2:0 output
format specifically.
- Use ARRAY_SIZE(format_str) for output format validity check (Ville)
V6: Added a separate function to calculate crtc_state->output_format, and
calling it from various get_config function (Fix CI build warning)
V7: Fixed checkpatch warnings for alignment
V8: Rebase
V9: Rebase
V10: Rebase
V11: Addressed review comments from Ville:
- Change check for CRTC output format from > ARRAY_SIZE to >= ARRAY_SIZE.
- Check for values < INTEL_OUTPUT_FORMAT_RGB is unnecessary.
- No need to get CRTC YCBCR config, for pre-BDW functions.
Added Ville's r-b.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-2-git-send-email-shashank.sharma@intel.com
PLLs are the source clocks for the DDIs so in order to determine the
ddi clock we need to check the PLL configuration.
For MG PHy Ports (C - F), depending on whether it is a TBT PLL or MG
PLL the link lock can be obtained from the the PLL divisors based on
the specification.
v2 (from Paulo):
* Make the algorithm look more like what's in the spec, also document
where we differ form the spec and why.
* Make the code a little more consistent with our coding style.
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180817215209.29133-2-paulo.r.zanoni@intel.com
Since Haswell we have no color range indication either in the pipe or
port registers for DP. Instead, there's a separate register for setting
the DP Main Stream Attributes (MSA) directly. The MSA register
definition makes no references to colorimetry, just a vague reference to
the DP spec. The connection to the color range was lost.
Apparently we've failed to set the proper MSA bit for limited, or CEA,
range ever since the first DDI platforms. We've started setting other
MSA parameters since commit dae847991a ("drm/i915: add
intel_ddi_set_pipe_settings").
Without the crucial bit of information, the DP sink has no way of
knowing the source is actually transmitting limited range RGB, leading
to "washed out" colors. With the colorimetry information, compliant
sinks should be able to handle the limited range properly. Native
(i.e. non-LSPCON) HDMI was not affected because we do pass the color
range via AVI infoframes.
Though not the root cause, the problem was made worse for DDI platforms
with commit 55bc60db59 ("drm/i915: Add "Automatic" mode for the
"Broadcast RGB" property"), which selects limited range RGB
automatically based on the mode, as per the DP, HDMI and CEA specs.
After all these years, the fix boils down to flipping one bit.
[Per testing reports, this fixes DP sinks, but not the LSPCON. My
educated guess is that the LSPCON fails to turn the CEA range MSA into
AVI infoframes for HDMI.]
Reported-by: Michał Kopeć <mkopec12@gmail.com>
Reported-by: N. W. <nw9165-3201@yahoo.com>
Reported-by: Nicholas Stommel <nicholas.stommel@gmail.com>
Reported-by: Tom Yan <tom.ty89@gmail.com>
Tested-by: Nicholas Stommel <nicholas.stommel@gmail.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=100023
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107476
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94921
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.9+
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180814060001.18224-1-jani.nikula@intel.com
This sequence is used to setup voltage swing before enabling MG PHY DDI
as well as for changing the voltage during DisplayPort Link training.
For ICL, there are two types of DDIs. This sequence needs to be used
for MG PHY DDI which is ports C-F.
v6 (From Manasi):
* Add programming for MG_CLKHUB and MG_TX_DCC as per the
spec updates
v5 (from Paulo):
* Checkpatch.
v4 (from Paulo):
* Fix bogus error message
* Fix copy+paste bugs (missing s/TX1/TX2/ after copy+paste)
* Use the new mask names
* Stay under 80 columns
* Add some blank lines
v3:
* Clear the regs before writing (Paulo)
v2:
* Rename to MG PHY in the function def (Jani Nikula)
* Rebase on top of new revision of other patches in series
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530225344-20373-2-git-send-email-manasi.d.navare@intel.com
On GLK NUC platforms the HDMI retiming buffer needs additional disabled
time to correctly sync to a faster incoming signal.
When measured on a scope the highspeed lines of the HDMI clock turn off
for ~400uS during a normal resolution change. The HDMI retimer on the
GLK NUC appears to require at least a full frame of quiet time before a
new faster clock can be correctly sync'd. Wait 100ms due to msleep
inaccuracies while waiting for a completed frame. Add a quirk to the
driver for GLK boards that use ITE66317 HDMI retimers.
V2: Add more devices to the quirk list
V3: Delay increased to 100ms, check to confirm crtc type is HDMI.
V4: crtc type check extended to include _DDI and whitespace fixes
v5: Fix white spaces, remove the macro for delay. Revert the crtc type
check introduced in v4.
Cc: Imre Deak <imre.deak@intel.com>
Cc: <stable@vger.kernel.org> # v4.14+
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105887
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Tested-by: Daniel Scheller <d.scheller.oss@gmail.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180710200205.1478-1-radhakrishna.sripada@intel.com
We can simplify the encoder's get_power_domains() hook by calling it
only if the encoder is active. That way the hook can return its power
domains unconditionally without checking the active state by calling
encoder::get_hw_state(). This get_hw_state() query is in fact
redundant since it's already done by intel_modeset_readout_hw_state()
setting the encoder's crtc or leaving it NULL accordingly. Let's use
this fact to decide if the encoder is active.
While at it clarify the comment in intel_ddi_get_power_domains() about
primary vs. fake MST encoders and make sure we never do an incorrect
encoder->dig_port cast for fake MST encoders.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705122654.17072-1-imre.deak@intel.com
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 141432
Addresses-Coverity-ID: 141433
Addresses-Coverity-ID: 141434
Addresses-Coverity-ID: 141435
Addresses-Coverity-ID: 141436
Addresses-Coverity-ID: 1357360
Addresses-Coverity-ID: 1357403
Addresses-Coverity-ID: 1357433
Addresses-Coverity-ID: 1392622
Addresses-Coverity-ID: 1415273
Addresses-Coverity-ID: 1435752
Addresses-Coverity-ID: 1441500
Addresses-Coverity-ID: 1454596
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628223541.GA17665@embeddedor.com
So far we got an AUX power domain reference only for the duration of DP
AUX transfers. However, the following suggests that we also need these
for main link functionality:
- The specification doesn't state whether it's needed or not for main
link functionality, but suggests that these power wells need to be
enabled already during display core initialization (Sequences to
Initialize Display).
- For PSR we need to keep the AUX power well enabled.
- On ICL combo PHY ports (non-TC) the AUX power well is needed for
link training too: while the port is enabled with a DP link training
test pattern trying to toggle the AUX power well will time out.
- On ICL MG PHY ports (TC) the AUX power well is needed also for main
link functionality (both in DP and HDMI modes).
- Windows enables these power wells both for main and AUX lane
functionality.
Based on the above take an AUX power reference for main link
functionality too. This makes a difference only on GEN10+ (GLK+)
platforms, where we have separate port specific AUX power wells.
For PSR we still need to distinguish between port A and the other
ports, since on port A DC states must stay enabled for main link
functionality, but DC states must be disabled for driver initiated
AUX transfers. So re-use the corresponding helper from intel_psr.c.
Since we take now a reference for main link functionality on all DP
ports we can forgo taking the separate power ref for PSR functionality.
v2:
- Make sure DC states stay enabled when taking the ref on port A.
(Ville)
v3: (Ville)
- Fix comment about logic for encoders without a crtc state and
add FIXME note for a simplification to avoid calling get_power_domains
in such cases.
- Use intel_crtc_has_dp_encoder() instead !intel_crtc_has_type(HDMI).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
[Clarified code comments in intel_ddi_main_link_aux_domain() and
intel_ddi_get_power_domains() (Imre)]
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180621184449.26634-1-imre.deak@intel.com
