Boards based on imx23 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx23.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Most of the i.MX NXP reference board dts files have already been
converted, so switch the remaining ones.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Most of the wandboard dts files have already been converted, so switch
the remaining ones.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx50-evk has duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx50.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6SLL EVK board has WDOG_B pin connected to the PMIC;
Add the WDOG_B pinctrl entry and 'fsl,ext-reset-output'
property to wdog node to let watchdog trigger a system
POR reset via the PMIC.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SLL EVK board, there is a debug LED controlled
by MX6SLL_PAD_EPDC_VCOM1__GPIO2_IO04 pin, add support
for it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx6qdl-sabreauto boards have a pcie slot so let's enable it.
Tested on imx6dl-sabreauto with an atk9k wifi card; scanning works.
There are unhandled differences for imx6qp but imx6qp-sabreauto.dts
already contains a snippet explicitly disabling the &pcie node so that
can be dealt with later.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx6sl have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx6sl.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx6sx have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx6sx.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx6ul have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx6ul.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add memory node to board dts.
This is done in preparation of removing the memory node from imx6ul.dtsi.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Current imx7d-sdb.dts has some incorrect settings about
Rev-A and Rev-B boards, some of the settings are based on
Rev-A board but some are based on Rev-B board, clean up it
by adding i.MX7D SDB Rev-A board support, make default
imx7d-sdb.dts for Rev-B board as usual, and introduce
imx7d-sdb-reva.dts for Rev-A board. Below are the affected
differences of Rev-A and Rev-B board:
Rev-A Rev-B
USB_OTG2_PWR: UART3_CTS_B GPIO1_IO07
ENET_EN_B: None GPIO1_IO04
TP_INT_B: EPDC_DATA13 EPDC_BDR1
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds support for the emtrion GmbH emCON-MX6 modules.
They are available with imx.6 Solo, Dual-Lite, Dual and Quad
equipped with Memory from 512MB to 2GB (configured by U-Boot).
Our default developer-Kit ships with the Avari baseboard and the
EDT ETM0700G0BDH6 Display (imx6[q|dl]-emcon-avari).
The devicetree is split into the common part providing all module
components and the basic support for all SoC versions
(imx6qdl-emcon.dtsi) and parts which are i.mx6 S|DL and D|Q relevant.
Finally the support for the avari baseboard in the developer-kit
configuration is provided by the emcon-avari dts files.
Signed-off-by: Jan Tuerk <jan.tuerk@emtrion.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adding the label cpu0 allows the adjustment of cpu-parameters
by reference in overlaying dtsi files in the same way as it
is possible for imx6q devices.
Signed-off-by: Jan Tuerk <jan.tuerk@emtrion.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Some SOCs in the i.MX6 family have a USB host controller that is
only capable of the HSIC interface and has no on-board PHY.
To be able to use these controllers, we need to add "usb-nop-xceiv"
dummy PHYs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
From i.MX6SX reference manual CCM chapter, KPP and
WDOGn use IPG clock as their clock, specify IPG
clock for KPP and WDOGn instead of DUMMY clock.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Removed the wrong compatible string "snps,dw-pcie", in case
match incorrect driver.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx7 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx7s.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx35 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx35.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx31 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx31.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to Documentation/devicetree/bindings/media/fsl-pxp.txt,
only one PXP clock needs to be described and it should be named
"axi".
Also pass the compatible string as suggested in the bindings doc.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove "regulator-always-on" property for vddpu regulator
since it can be OFF when GPU power domain is OFF.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The "fsl,mf-mix-wakeup-irq" is ONLY used as a temporary
solution in NXP's internal tree for Mega/Fast Mix off
feature after suspend, upstream kernel does NOT need it,
remove it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx53 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx53.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx51 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx51.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX fixes for 4.20, round 3:
- A couple of fixes on imx7d-pico and imx7d-nitrogen7 boards to correct
the description of the Wifi clock.
- Change SW2ISO count to get a safer ARM LDO ramp-up time, so that
different boards can be covered. This fixes the ARM LDO failure seen
on some customer boards.
* tag 'imx-fixes-4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx7d-nitrogen7: Fix the description of the Wifi clock
ARM: imx: update the cpu power up timing setting on i.mx6sx
ARM: dts: imx7d-pico: Describe the Wifi clock
Signed-off-by: Olof Johansson <olof@lixom.net>
The 50ms debounce is too low and give ghost bounces on some
platforms. Bump it to 100ms to make it stable.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the FOTG210 USB host controller to the Gemini
device trees. In the main SoC DTSI it is flagged as disabled
and then it is selectively enabled on the devices that utilize
it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This sets the partition information on the SQ201 to be read
out from the RedBoot partition table, removes the static
partition table and sets our boot options to mount root from
/dev/mtdblock2 where the squashfs+JFFS2 resides.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some Gemini platforms have a parallel NOR flash which conflicts
with use cases reusing some of the flash lines (such as CE1)
for GPIO.
Fix this on the D-Link DIR-685 and Itian SQ201 by creating
"enabled" and "disabled" states for the flash pin control
handle, and rely on the flash handling code to switch this
in and out when accessed so these lines can be used
for GPIO when flash is not accessed, and enable flash
access.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The vendor firmware was analyzed to get the right idea about
this flash layout. /proc/mtd contains:
dev: size erasesize name
mtd0: 01e7ff40 00020000 "rootfs"
mtd1: 01f40000 00020000 "upgrade"
mtd2: 00040000 00020000 "rgdb"
mtd3: 00020000 00020000 "nvram"
mtd4: 00040000 00020000 "RedBoot"
mtd5: 00020000 00020000 "LangPack"
mtd6: 02000000 00020000 "flash"
Here "flash" is obviously the whole device and we know "rootfs"
is a bogus hack to point to a squashfs rootfs inside of the main
"upgrade partition". We know "RedBoot" is the first 0x40000 of
the flash and the "upgrade" partition follows from 0x40000 to
0x1f8000. So we have mtd0, 1, 4 and 6 covered.
Remains:
mtd2: 00040000 00020000 "rgdb"
mtd3: 00020000 00020000 "nvram"
mtd5: 00020000 00020000 "LangPack"
Inspecting the flash at 0x1f8000 and 0x1fa000 reveals each of
these starting with "RGCFG1" so we assume 0x1f8000-1fbfff is
"rgdb" of 0x40000.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Earlier attempt to move am335x mcasp to probe with ti-sysc
interconnect target module caused audio to stop working and and
the dts changes were reverted by commit 5d2632a577 ("ARM: dts:
Revert am335x mcasp ti-sysc changes").
Turns out we were missing the l3 data port ranges for mcasp. This
caused mcasp dma to attempt to use wrong port address. So let's
try again essentially reverting the earlier revert and adding the
missing l3 data port ranges.
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It was noticed that unbinding and rebinding the KSZ8851 ethernet
resulted in the driver reporting "failed to read device ID" at probe.
Probing the reset line with a 'scope while repeatedly attempting to
bind the driver in a shell loop revealed that the KSZ8851 RSTN pin is
constantly held at zero, meaning the device is held in reset, and
does not respond on the SPI bus.
Experimentation with the startup delay on the regulator set to 50ms
shows that the reset is positively released after 20ms.
Schematics for this board are not available, and the traces are buried
in the inner layers of the board which makes tracing where the RSTN pin
extremely difficult. We can only guess that the RSTN pin is wired to a
reset generator chip driven off the ethernet supply, which fits the
observed behaviour.
Include this delay in the regulator startup delay - effectively
treating the reset as a "supply stable" indicator.
This can not be modelled as a delay in the KSZ8851 driver since the
reset generation is board specific - if the RSTN pin had been wired to
a GPIO, reset could be released earlier via the already provided support
in the KSZ8851 driver.
This also got confirmed by Peter Ujfalusi <peter.ujfalusi@ti.com> based
on Blaze schematics that should be very close to SDP4430:
TPS22902YFPR is used as the regulator switch (gpio48 controlled):
Convert arm boot_lock to raw The VOUT is routed to TPS3808G01DBV.
(SCH Note: Threshold set at 90%. Vsense: 0.405V).
According to the TPS3808 data sheet the RESET delay time when Ct is
open (this is the case in the schema): MIN/TYP/MAX: 12/20/28 ms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated with notes from schematics from Peter]
Signed-off-by: Tony Lindgren <tony@atomide.com>
When a micro SD card is inserted in the PDU001 card cage, the card
detection switch is opened and the corresponding GPIO input is driven
by a pull-up. Hence change the active level of the card detection
input from low to high.
Signed-off-by: Felix Brack <fb@ltec.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP5's Super-Speed USB port has a software mailbox register
that needs to be fed with VBUS and ID events from an external
VBUS/ID comparator.
Without this, Host role will not work correctly.
Fixes: 656c1a65ab ("ARM: dts: omap5: enable OTG role for DWC3 controller")
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The R40 has an RTC hardware block, which has additional registers
that are not related to RTC or clock functions, and is otherwise
compatible with the H3's RTC.
Add a device node for it, and fix up any references to the LOSC.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The RTC module on the H3 was claimed to be the same as on the A31, when
in fact it is not. The A31 does not have an RTC external clock output,
and its internal RC oscillator's average clock rate is not in the same
range. The H5's RTC has some extra crypto-related registers compared to
the H3. Their exact functions are not clear. Also the RTC-VIO regulator
has different settings.
This patch fixes the compatible string and clock properties to conform
to the updated bindings. The device node for the internal oscillator is
removed, as it is internalized into the RTC device. Clock references to
the IOSC and LOSC are also fixed.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The RTC module on the A23 was claimed to be the same as on the A31, when
in fact it is not. The A31 does not have an RTC external clock output,
and its internal RC oscillator's average clock rate is not in the same
range. The A33's RTC is the same as the A23.
This patch fixes the compatible string and clock properties to conform
to the updated bindings. The register range is also fixed.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Arndale boards have wires for DSI and eDP panels, but in-kernel support
for eDP panels is broken for long time and breaks display support even on
boards with DSI panels.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Edison 2 Quad-Core was a Tablet device released in 2013 by MundoReader
using a rk3188 soc. Add a devicetree for it.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Add the Video Processing Unit node for RK3288 SoC.
Fix the VPU IOMMU node, which was disabled and lacking
its power domain property.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
According to bindings/regulator/fixed-regulator.txt the 'clocks' and
'clock-names' properties are not valid ones.
In order to turn on the Wifi clock the correct location for describing
the CLKO2 clock is via a mmc-pwrseq handle, so do it accordingly.
Fixes: 56354959cf ("ARM: dts: imx: add Boundary Devices Nitrogen7 board")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The R40 datasheet specifies a tolerance range for the external
oscillators used. Add them to the device tree as the clock accuracy.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The H3 datasheet specifies a tolerance range for the external
oscillators used. Add them to the device tree as the clock accuracy.
The internal oscillator is left unchanged, as it will be removed later.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
We need to add mcasp l3 port ranges for mcasp to use a correct l3
data port address for dma.
Fixes: d95adfd458 ("ARM: dts: am437x: Move l4 child devices to
probe them with ti-sysc")
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The iWave RZ/G1N board is almost identical to RZ/G1M. cmt and rwdt modules
are SoC specific and should be part of board dts rather than SoM dtsi. By
moving these nodes to the common dtsi it allows cmt and rwdt to be enabled
on both of these boards with less lines of code.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
