Simplify model and compatible by dropping the 256/512 MB from the model,
-512 from the compatible and rename that property from toradex,iris to
toradex,colibri_t20-iris to be more in-line with all our other device
trees.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Simplify model and compatible by dropping the 256/512 MB from the model
and -512 from the compatible properties to be more in-line with all our
other device trees.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Support the V1.1 hardware revisions with the following change:
Changed power rail for MMC1 interface to a 3.3V/1.8V switchable rail in
order to be able to run UHS SD cards in ultra high speed 1.8V mode.
[ 207.502011] mmc2: host does not support reading read-only switch,
assuming write-enable
[ 207.517011] mmc2: new ultra high speed SDR104 SDHC card at address
aaaa
[ 207.534190] mmcblk2: mmc2:aaaa SE32G 29.7 GiB
[ 207.545096] mmcblk2: p1
root@apalis-t30:~# cat /sys/kernel/debug/mmc2/ios
clock: 208000000 Hz
actual clock: 204000000 Hz
vdd: 21 (3.3 ~ 3.4 V)
bus mode: 2 (push-pull)
chip select: 0 (don't care)
power mode: 2 (on)
bus width: 2 (4 bits)
timing spec: 6 (sd uhs SDR104)
signal voltage: 1 (1.80 V)
driver type: 0 (driver type B)
root@apalis-t30:~# hdparm -t /dev/mmcblk2
/dev/mmcblk2:
Timing buffered disk reads: 256 MB in 3.02 seconds = 84.71 MB/sec
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
PLX Technology meanwhile got bought by Broadcom Corporation but the
vendor prefix plx is still used in 8 current device trees. This silences
the following checkpatch.pl warning:
WARNING: DT compatible string vendor "plx" appears un-documented
-- check ./Documentation/devicetree/bindings/vendor-prefixes.txt
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the actual dts for the tinker board S, which brings its own emmc
device, not therefore not requiring an sd-card to boot.
Signed-off-by: David Summers <beagleboard@davidjohnsummers.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rockpro64 is a rockchip RK3399 based board from pine64.org.
This patch adds basic device node support for Rockpro64 board and make it able
to bring up.
Peripheral Works
- Sdcard
- USB 2.0, 3.0
- Leds
- Ethernet
- Debug console
Not working:
- USB Type-C
Signed-off-by: Akash Gajjar <Akash_Gajjar@mentor.com>
Acked-by: Deepak Das <Deepak_Das@mentor.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add documentation to describe Xilinx ZynqMP firmware driver
bindings. Firmware driver provides an interface to firmware
APIs. Interface APIs can be used by any driver to communicate
to PMUFW (Platform Management Unit).
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
soc: driver soc update for v4.20
- Enable host-id as an optional dt property
- Fix minor typo in knav driver
* tag 'drivers_soc_for_4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
soc: ti: fix spelling mistake "instace" -> "instance"
firmware: ti_sci: Provide host-id as an optional dt parameter
Documentation: dt: keystone: ti-sci: Add optional host-id parameter
Signed-off-by: Olof Johansson <olof@lixom.net>
The coresight drivers relied on default bindings for graph
in DT, while reusing the "reg" field of the "ports" to indicate
the actual hardware port number for the connections. This can
cause duplicate ports with same addresses, but different
direction. However, with the rules getting stricter for the
address mismatch with the label, it is no longer possible to use
the port address field for the hardware port number.
This patch introduces new DT binding rules for coresight
components, based on the same generic DT graph bindings, but
avoiding the address duplication.
- All output ports must be specified under a child node with
name "out-ports".
- All input ports must be specified under a childe node with
name "in-ports".
- Port address should match the hardware port number.
The support for legacy bindings is retained, with a warning.
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the bindings for maxim max98088/9 audio codec.
Signed-off-by: Andreas Färber <afaerber@suse.de>
[m.felsch@pengutronix.de: adapt commit message]
[m.felsch@pengutronix.de: adapt formatting]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Update the compatible string for UFS QMP PHY on SDM845.
Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds a new optional property "renesas,no-otg-pins" which
a board does not provide proper otg pins.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Document the compatible string "brcm,bcm63138-sata-phy" as a valid
compatible string describing the standard Broadcom SATA PHY block.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add DT bindings for PHY interface built into PCIe controller implemented
in UniPhier SoCs.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Update device tree binding documentation of TI's dra7xx PCI controller
for enabling unaligned mem access as applicable not just in EP mode but
in host mode as well.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The existing IOMMU bindings cannot be used to specify the relationship
between fsl-mc devices and IOMMUs. This patch adds a generic binding for
mapping fsl-mc devices to IOMMUs, using iommu-map property.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
On the D3 and E3 SoCs, the LVDS encoder can derive its internal pixel
clock from an externally supplied clock, either through the EXTAL pin or
through one of the DU_DOTCLKINx pins. Add corresponding clocks to the DT
bindings.
To retain backward compatibility with DT that don't specify the
clock-names property, the functional clock must always be specified
first, and the clock-names property is optional when only the functional
clock is specified.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Add "marvell,prestera" as a compatible string so that drivers can be
written to account for any prestera variant without needing to
specialise to the more specific values.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 4.20, please pull the following:
- Rafal updates the Broadcom BCM5301x (Northstar) DTS files to use the
new style partition parser and removes the unsupported/undocumented
linux,part-probe properties that were previously introduced
- Stefan adds supports for the Raspberry Pi Compute Module 3/3Lite, he
also updates the Raspberry Pi 3B+ USB Ethernet adapter to have proper
LED configuration
- Rob fixes a bunch of SPI bus warnings in the Northstar Plus and
Hurricane 2 DTS files
- Florian documents the Broadcom roboswitch Switch Register Access Block
(SRAB) interrupts, adds the switch interrupts to the Northstar Plus
DTS include file and finally updates the BCM958625HR reference board to
have the proper SFP module definition
* tag 'arm-soc/for-4.20/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm: Fix SPI bus warnings
ARM: dts: NSP: Wire up switch interrupts
dt-bindings: net: dsa: Document B53 SRAB interrupts and registers
ARM: dts: NSP: Enable SFP on bcm958625hr
ARM: dts: bcm283x-rpi-lan7515: Enable Ethernet LEDs
ARM: dts: BCM5301X: Specify flash partitions
ARM: dts: add Raspberry Pi Compute Module 3 and IO board
dt-bindings: bcm: Add Raspberry Pi CM3 and CM3L
Signed-off-by: Olof Johansson <olof@lixom.net>
New soc support for the px30 quad-core Cortex-A35.
New boards are the px30 eval board and roc-rk3399-pc.
The rk3328 got support for the one gpio controlled via the general
register files and the rk3399 finally got its idle-states defined.
And finally fixes and improvements for firefly-rk3399 (wifi),
roc-rk3328-cc (sdmmc-uhs, io-domains), rk3328-rock64 (gpio-regulator
pin fix) and rk3399-sapphire (gpio-regulator pin fix, pmic pin fix
and type-c port supply).
* tag 'v4.20-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Add type-c port supply on rk3399-sapphire board
arm64: dts: rockchip: fix vcc_host1_5v pin assign on rk3328-rock64
arm64: dts: rockchip: add WiFi module support for Firefly-RK3399
arm64: dts: rockchip: remove dvs2 pinctrl from pmic on rk3399-sapphire
arm64: dts: rockchip: Fix VCC5V0_HOST_EN on rk3399-sapphire
arm64: dts: rockchip: re-order vcc_sys on rk3399-sapphire
arm64: dts: rockchip: add missing vop properties for px30
arm64: dts: rockchip: Add idle-states to device tree for rk3399
arm64: dts: rockchip: add sdmmc UHS support for roc-rk3328-cc
arm64: dts: rockchip: add GRF GPIO controller to rk3328
arm64: dts: rockchip: add io-domain to roc-rk3328-cc
arm64: dts: rockchip: add PX30 evaluation board devicetree
arm64: dts: rockchip: add core dtsi file for PX30 SoCs
dt-bindings: rockchip: grf: add grf and pmugrf description for px30
arm64: dts: rockchip: add support for ROC-RK3399-PC board
Signed-off-by: Olof Johansson <olof@lixom.net>
This driver was originally written by ST in 2016 as a misc input device
driver, and hasn't been maintained for a long time. I grabbed some code
from it's API and reformed it into an iio proximity device driver.
This version of driver uses i2c bus to talk to the sensor and
polling for measuring completes, so no irq line is needed.
It can be tested with reading from
/sys/bus/iio/devices/iio:deviceX/in_distance_input
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Allow the configuration of the MDIO clock divider when the Device Tree
contains 'clock-frequency' property (similar to I2C and SPI buses).
Because the hardware may have lost its state during suspend/resume,
re-apply the MDIO clock divider upon resumption.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unit addresses of the Cortex-A9 SCU device nodes contain too many
zeroes. Remove them.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We remove the references to anything but two-cell GPIO specifiers
and just mention that controllers need to specify their bindings
and that we strongly recommend two-cell bindings.
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In 2011 the commit bf859f84a1
("gpio/dt: Refine GPIO device tree binding") introduced an
experimental BNF notation for defining a regular grammar for
the GPIO phandles used by different devices.
This was an interesting approach, and shows that we have long
nutured the idea to formally verify device tree files using
regular grammar.
Most if not all other bindings use natural language to define
the bindings, and the recent thinking for verifying device
tree files is to use JSON schemas in separate definitions.
Cut the BNF business and replace it with natural language
so that it becomes more human-readable for now.
Cc: devicetree@vger.kernel.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Kumar Gala <galak@kernel.crashing.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
R-Car Gen3 needs to enable clocks of both host and peripheral.
Otherwise, other side device cannot work correctly. So, this patch
adds a property of clock-names for R-Car Gen3 as an optional.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
