The default capless power mode is low voltage mode. We should set
it to high voltage mode to get fair headphone performance.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The i2s clock pre-divider 1 is used for both i2s1 and sysclk.
The i2s1 is usually used for the main i2s and the pre-divider
will be set in hw_params function.
However, if i2s2 is used, the pre-divider is not set in the hw_params
function and the default value of i2s clock pre-divider 1 is too high
for sysclk and DMIC usage. Fix by overriding default divider value to 2.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=95681
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As requirements to bring up audio paths are continuous getting tighter
and the DSP download to most ADSP devices happens over an external bus
it can become an important factor in the path bring up time. As such
sometimes it is a reasonable trade off to download the firmware ahead of
when it will be required and take a small hit on power consumption for
keeping the core powered up.
This "preloading" adds an additional control for each DSP core "DSPx
Preload Switch" that when set to true will power up the DSP core and
download the firmware currently selected in the "DSPx Firmware" control.
Whilst the core is preloaded the current firmware can not be changed and
the CODEC will be kept powered up and SYSCLK held on. Although future
improvements may allow the SYSCLK to be powered down as well because
the hardware only requires SYSCLK whilst the download is actually taking
place, but this is not covered in this series.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"DAC L2 Power" and "DAC R2 Power" are used by both rt5639 and rt5640.
But it was defined in rt5640_specific_dapm_widgets[]. Move them to
rt5640_dapm_widgets will let both rt5639 and rt5640 can use it.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The clk_ref_div is not configured in the correct position of the
register. The patch fixes that clk_ref_div, Pre-Scalar, is assigned
the wrong value.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the codec is powered on, it's registers are in reset state as the
power off will do a soft reset of the codec.
After the register sync we need to add delay to remove the pop-noise on
stream start.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The RESET register only have one self clearing bit and it should not be
cached. If it is cached, when we sync the registers back to the chip we
will initiate a software reset as well, which is not desirable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Protect against corrupt firmware files by ensuring that the length we
get for the data in a region actually lies within the available firmware
file data buffer.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For TDM mode, the I2S data out line can be shared between mutliple
codecs. In this scenario, only the active codec should be using
the line, and all others should be high impedance. However,
currently in the driver this configuration isn't set when capture
is inactive, and the line remains driven.
This patch updates the AIF_OUT widget to set the DAI output pin of
the device as high impedance when not in use.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/rt5677-spi.c does not use any miscdevice so this patch
remove this unnecessary inclusion.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/rt5514-spi.c does not use any miscdevice so this patch
remove this unnecessary inclusion.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a control to allow swapping HiFi DAC Left/Right channels.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
In pcm3168a_hw_params(), 'format' is initialized but never used.
sound/soc/codecs/pcm3168a.c: In function ‘pcm3168a_hw_params’:
sound/soc/codecs/pcm3168a.c:405:19: warning: variable ‘format’ set but not
used [-Wunused-but-set-variable]
snd_pcm_format_t format;
Cc: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In max9867_dai_set_fmt(), 'ret' is initialized as return value of
regmap_raw_write() but never checked, so remove this and assignement.
sound/soc/codecs/max9867.c: In function ‘max9867_dai_set_fmt’:
sound/soc/codecs/max9867.c:312:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret;
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In adau17x1_pll_event(), 'ret' is initialized as return value of
regmap_raw_write() but never checked, so remove this and assignement.
sound/soc/codecs/adau17x1.c: In function ‘adau17x1_pll_event’:
sound/soc/codecs/adau17x1.c:68:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret;
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In max98090_probe(), code checks for micbias being out of range. The
'micbias' variable in unsigned and checked against M98090_MBVSEL_2V2 which
is zero, so remove this check.
sound/soc/codecs/max98090.c: In function ‘max98090_probe’:
sound/soc/codecs/max98090.c:2459:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
} else if (micbias < M98090_MBVSEL_2V2 || micbias > M98090_MBVSEL_2V8) {
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull sound updates from Takashi Iwai:
"No dramatic changes are found in this development cycle, but as usual,
many commits are applied in a wide range of drivers.
Most of big changes are in ASoC, where a few bits of framework work
and quite a lot of cleanups and improvements to existing code have
been done. The rest are usual stuff, a few HD-audio and USB-audio
quirks and fixes, as well as the drop of kthread usages in the whole
subsystem.
Below are some highlights:
ASoC:
- support for stereo DAPM controls
- some initial work on the of-graph sound card
- regmap conversions of the remaining AC'97 drivers
- a new version of the topology ABI; this should be backward
compatible
- updates / cleanups of rsnd, sunxi, sti, nau8825, samsung, arizona,
Intel skylake, atom-sst
- new drivers for Cirrus Logic CS42L42, Qualcomm MSM8916-WCD, and
Realtek RT5665
USB-audio:
- yet another race fix at disconnection
- tolerated packet size calculation for some Android devices
- quirks for Axe-Fx II, QuickCam, TEAC 501/503
HD-audio:
- improvement of Dell pin fixup mapping
- quirks for HP Z1 Gen3, Alienware 15 R2 2016 and ALC622 headset mic
Misc:
- replace all kthread usages with simple works"
* tag 'sound-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (296 commits)
ALSA: hiface: Fix M2Tech hiFace driver sampling rate change
ALSA: usb-audio: Eliminate noise at the start of DSD playback.
ALSA: usb-audio: Add native DSD support for TEAC 501/503 DAC
ASoC: wm_adsp: wm_adsp_buf_alloc should use kfree in error path
ASoC: topology: avoid uninitialized kcontrol_type
ALSA: usb-audio: Add QuickCam Communicate Deluxe/S7500 to volume_control_quirks
ALSA: usb-audio: add implicit fb quirk for Axe-Fx II
ASoC: zte: spdif: correct ZX_SPDIF_CLK_RAT define
ASoC: zte: spdif and i2s drivers are not zx296702 specific
ASoC: rsnd: setup BRGCKR/BRRA/BRRB when starting
ASoC: rsnd: enable/disable ADG when suspend/resume timing
ASoC: rsnd: tidyup ssi->usrcnt counter check in hw_params
ALSA: cs46xx: add a new line
ASoC: Intel: update bxt_da7219_max98357a to support quad ch dmic capture
ASoC: nau8825: disable sinc filter for high THD of ADC
ALSA: usb-audio: more tolerant packetsize
ALSA: usb-audio: avoid setting of sample rate multiple times on bus
ASoC: cs35l34: Simplify the logic to set CS35L34_MCLK_CTL setting
ALSA: hda - Gate the mic jack on HP Z1 Gen3 AiO
ALSA: hda: when comparing pin configurations, ignore assoc in addition to seq
...
This bit will enable 4th order SINC filter.
=1, filter will enable; but it consumes higher power.
=0, the sinc filter is disable, and it should always keep 0 value to
get high THD.
Therefor, disable the filter when codec initiation for better
performance when recording.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The logic of "value = ~CS35L34_MCLK_DIV & CS35L34_MCLK_RATE_XXXXXX;" is
unnecessary complex. By setting CS35L34_MCLK_DIV | CS35L34_MCLK_RATE_MASK
as the mask for regmap_update_bits() call, what the code does is exactly
the same as setting value = CS35L34_MCLK_RATE_XXXXXX.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using regmap_update_bits(..., mask, 1) with 'mask' following (1 << k)
and k greater than 0 is wrong. Indeed, _regmap_update_bits will perform
(mask & 1), which results in 0 if LSB of mask is 0. Thus the call
regmap_update_bits(..., mask, 1) is in reality equivalent to
regmap_update_bits(..., mask, 0).
In such a case, the correct use is regmap_update_bits(..., mask, mask).
This driver is performing such a mistake with the CS42L56_AIN*_REF_MASK
masks, which equal 0x10, 0x20, 0x40 and 0x80. Fix the driver to make it
consistent with the API. Please note that this change is untested,
as I do not have this piece of hardware. Testers are welcome!
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is an issue about pop noise in NAU88L25 as follows.
Issue 54078: Chell_headphone pop back from S3
(1)Play directly to hw, bypassing CRAS:
sox -b 16 -n -t alsa hw:0,0 synth sine 200 sine 200
(2)Close lid or powerd_dbus_suspend, then press a key to resume.
(3)no audio after resume
(4)Audio will be back after close then reopen the pcm device.
After verification, we find one defect is that semaphone lock is not
long enough and expired. In this situation, the playback comes back
early but pauses a while to wait for the crosstalk detection done.
But the detection spends too much time and lock time is up. Therefore,
the playback and jack detection sequence interfere to each other.
That breaks sequence and makes noise. The driver extends the lock
time for the issue.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to modify the state of some of our own pins and are currently
not taking account that the pin name may have a name_prefix applied
to it.
Replace the snd_soc_dapm_x_pin functions with the equivalent
snd_soc_component_x_pin functions so that any name_prefix will be
handled automatically.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5670 driver supports also RT5672 codec, but its ACPI ID is missing.
This was found on Dell Wyse 3040 box.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Dell Wyse 3040 requires the platform workaround for enabling dmic and
jack detection as defined for Braswell CRB.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
drm/virtio: fix busid in a different way, allocate more vbufs.
drm/qxl: various bugfixes and cleanups,
* tag 'drm-qemu-20161121' of git://git.kraxel.org/linux: (224 commits)
drm/virtio: allocate some extra bufs
qxl: Allow resolution which are not multiple of 8
qxl: Don't notify userspace when monitors config is unchanged
qxl: Remove qxl_bo_init() return value
qxl: Call qxl_gem_{init, fini}
qxl: Add missing '\n' to qxl_io_log() call
qxl: Remove unused prototype
qxl: Mark some internal functions as static
Revert "drm: virtio: reinstate drm_virtio_set_busid()"
drm/virtio: fix busid regression
drm: re-export drm_dev_set_unique
Linux 4.9-rc5
gp8psk: Fix DVB frontend attach
gp8psk: fix gp8psk_usb_in_op() logic
dvb-usb: move data_mutex to struct dvb_usb_device
iio: maxim_thermocouple: detect invalid storage size in read()
aoe: fix crash in page count manipulation
lightnvm: invalid offset calculation for lba_shift
Kbuild: enable -Wmaybe-uninitialized warnings by default
pcmcia: fix return value of soc_pcmcia_regulator_set
...
Disable IRQ when jack is NULL in rt298_mic_detect. So machine driver
can use it in suspend/resume.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Functions are given external linkage by default making the extern's
unnecessary, as such remove them.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Functions are given external linkage by default making the extern's
unnecessary, as such remove them.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fields of structs with global storage are implicitly initialized to 0/NULL,
there is usually no need to do this explicitly.
Removing the initialization of the legacy suspend/resume callback fields
also gets the driver ready for the day when they are eventually removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
