Replace all __u types with their u counterparts throughout the driver
(whose structures are not exported to user space).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Since forever this driver has had IXON and IXOFF mixed up, and has used
the latter rather than the former to enable hardware-assisted software
flow control on output.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
We already have the tty port when probing a usb-serial port so use
tty_port_register_device() directly instead of tty_port_install() later
to set up the port link.
This is a step towards enabling serdev for usb-serial (but we need to
determine how to handle hotplugging first).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Just set up the show callback in the tty_operations, and use
proc_create_single_data to create the file without additional
boilerplace code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
If we get an invalid device configuration from a palm 3 type device, we
might incorrectly parse things, and we have the potential to crash in
"interesting" ways.
Fix this up by verifying the size of the configuration passed to us by
the device, and only if it is correct, will we handle it.
Note that this also fixes an information leak of slab data.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ johan: add comment about the info leak ]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds support for ublox R410M PID 0x90b2 USB modem to option
driver, this module supports LTE Cat M1 / NB1.
Interface layout:
0: QCDM/DIAG
1: ADB
2: AT
3: RMNET
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The dwm-158 interface 4 and 5 doesn't answer to the AT commands
and doesn't appears a option interface.
Tested on openwrt distribution (kernel 4.14 using the old blacklist
definitions).
Lars Melin also writes:
Blacklisting interface 4 and 5 is correct because:
MI_00 D-Link Mobile Broadband Device (cdc_ether)
MI_02 D-Link HSPA+DataCard Diagnostics Interface (also ppp modem)
MI_03 D-Link HSPA+DataCard NMEA Device
MI_04 D-Link HSPA+DataCard Speech Port
MI_05 D-Link HSPA+DataCard Debug Port
MI_06 USB Mass Storage Device
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
[ johan: add Lars's comment on the interface layout and reword summary ]
Cc: Lars Melin <larsm17@gmail.com>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Arrow USB Blaster integrated on MAX1000 board uses the same vendor ID
(0x0403) and product ID (0x6010) as the "original" FTDI device.
This patch avoids picking up by ftdi_sio of the first interface of this
USB device. After that this device can be used by Arrow user-space JTAG
driver.
Signed-off-by: Vasyl Vavrychuk <vvavrychuk@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Johan writes:
USB-serial updates for v4.17-rc1
Here are the USB-serial updates for 4.17-rc1, including a
reimplementation of the option-driver interface masking which allows
for a more compact notation when adding new device entries.
Included are also a couple of clean ups and a new ftdi_sio device id.
All but the device-id commit have been in linux-next (without any
reported issues).
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds a device ID for the RT Systems cable used to
program Yaesu VX-8R/VX-8DR handheld radios. It uses the main
FTDI VID instead of the common RT Systems VID.
Signed-off-by: Major Hayden <major@mhtx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the USB class define rather than a magic number when refusing to
bind to mass-storage interfaces.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop redundant interface-class test for Samsung GT-B3730 modems for
which we only match and probe the CDC data interface.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reimplement interface masking using device flags stored directly in the
device-id table. This will make it easier to add and maintain device-id
entries by using a more compact and readable notation compared to the
current implementation (which manages pairs of masks in separate
blacklist structs).
Two convenience macros are used to flag an interface as either reserved
or as not supporting modem-control requests:
{ USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_ME910_DUAL_MODEM),
.driver_info = NCTRL(0) | RSVD(3) },
For now, we limit the highest maskable interface number to seven, which
allows for (up to 16) additional device flags to be added later should
need arise.
Note that this will likely need to be backported to stable in order to
make future device-id backports more manageable.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Quectel EP06 is a Cat. 6 LTE modem, and the interface mapping is as
follows:
0: Diag
1: NMEA
2: AT
3: Modem
Interface 4 is QMI and interface 5 is ADB, so they are blacklisted.
This patch should also be considered for -stable. The QMI-patch for this
modem is already in the -stable-queue.
v1->v2:
* Updated commit prefix (thanks Johan Hovold)
* Updated commit message slightly.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull driver core updates from Greg KH:
"Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with
reworks to try to attempt to make the code easier to handle in the
long run, but no functional change. There's also some tree-wide sysfs
attribute fixups with lots of acks from the various subsystem
maintainers, as well as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (48 commits)
device property: Define type of PROPERTY_ENRTY_*() macros
device property: Reuse property_entry_free_data()
device property: Move property_entry_free_data() upper
firmware: Fix up docs referring to FIRMWARE_IN_KERNEL
firmware: Drop FIRMWARE_IN_KERNEL Kconfig option
USB: serial: keyspan: Drop firmware Kconfig options
sysfs: remove DEBUG defines
sysfs: use SPDX identifiers
drivers: base: add coredump driver ops
sysfs: add attribute specification for /sysfs/devices/.../coredump
test_firmware: fix missing unlock on error in config_num_requests_store()
test_firmware: make local symbol test_fw_config static
sysfs: turn WARN() into pr_warn()
firmware: Fix a typo in fallback-mechanisms.rst
treewide: Use DEVICE_ATTR_WO
treewide: Use DEVICE_ATTR_RO
treewide: Use DEVICE_ATTR_RW
sysfs.h: Use octal permissions
component: add debugfs support
bus: simple-pm-bus: convert bool SIMPLE_PM_BUS to tristate
...
The pointer mos_parport is being initialized to pp->private_data and
then the assignment is duplicated after a spin lock. Remove the
initialization as it occurs before the spin lock and it is a redundant
assignment.
Cleans up clang warnings:
drivers/usb/serial/mos7720.c:521:26: warning: Value stored to
'mos_parport' during its initialization is never read
drivers/usb/serial/mos7720.c:557:26: warning: Value stored to
'mos_parport' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan writes:
USB-serial updates for v4.16-rc1
Here are the USB-serial updates for 4.16-rc1, including:
- a fix for a potential sleep-while-atomic (warning) in an io_edgeport
error path
- removal of a dummy TIOCSSERIAL implementation in ark3116
- new features for Fintek F81532/534 devices:
- support for higher baud rates (up to 1.5 Mbps)
- support for auto-RTS (for RS-485)
- support for transceiver configuration
- support for detecting disabled ports
Included are also various clean ups.
All have been (at least compile tested) in linux-next without any
reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81532/534 had 4 clocksource 1.846/18.46/14.77/24MHz and baud rates
can be up to 1.5Mbits with 24MHz. But on some baud rate (384~500kps), the
TX side will send the data frame too close to treat frame error on RX
side. This patch will force all TX data frame with delay 1bit gap.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81532/534 can be disable port by manufacturer with
following H/W design.
1: Connect DCD/DSR/CTS/RI pin to ground.
2: Connect RX pin to ground.
In driver, we'll implements some detect method likes following:
1: Read MSR.
2: Turn MCR LOOP bit on, off and read LSR after delay with 60ms.
It'll contain BREAK status in LSR.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
In the original code, We'll read configuration in calc_num_ports()
and read again in attach(). In fact, we can move all content from
attach() to calc_num_ports() to simplify the code.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
[ johan: replace commit summary ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81532/534 had 3 output pin (M0/SD, M1, M2) with open-drain mode to
control transceiver. We'll read it from internal Flash with address
0x2f05~0x2f08 for 4 ports. The value is range from 0 to 7. The M0/SD is
MSB of this value. For a examples, If read value is 6, we'll write M0/SD,
M1, M2 as 1, 1, 0.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81532/534 had auto RTS direction support for RS485 mode.
We'll read it from internal Flash with address 0x2f01~0x2f04 for 4 ports.
There are 4 conditions below:
0: F81534_PORT_CONF_RS232.
1: F81534_PORT_CONF_RS485.
2: value error, default to F81534_PORT_CONF_RS232.
3: F81534_PORT_CONF_RS485_INVERT.
F81532/534 Clock register (offset +08h)
Bit0: UART Enable (always on)
Bit2-1: Clock source selector
00: 1.846MHz.
01: 18.46MHz.
10: 24MHz.
11: 14.77MHz.
Bit4: Auto direction(RTS) control (RTS pin Low when TX)
Bit5: Invert direction(RTS) when Bit4 enabled (RTS pin high when TX)
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
[ johan: rename mode-mask define, and only use GENMASK() for masks ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81532/534 had 4 clocksource 1.846/18.46/14.77/24MHz and baud rates
can be up to 1.5Mbits with 24MHz.
This device may generate data overrun when baud rate setting to 921600bps
or higher with old UART trigger level setting (8x14=112) with full
loading. We'll change trigger level from 8x14=112 to 8x8=64 to avoid data
overrun.
Also the read/write of EP0 will be affected by this patch. The worst case
of responding time is 20s when all serial port are full loading and trying
to access EP0, so we change EP0 timeout from 10 to 20s.
F81532/534 Clock register (offset +08h)
Bit0: UART Enable (always on)
Bit2-1: Clock source selector
00: 1.846MHz.
01: 18.46MHz.
10: 24MHz.
11: 14.77MHz.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
[ johan: only use GENMASK() for masks ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The patch moves TIOCGSERIAL ioctl case to get_serial_info function.
Signed-off-by: Mikhail Zaytsev <flashed@mail.ru>
[johan: keep the automatic __user pointer variable in ioctl callback ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The patch removes unused TIOCSSERIAL ioctl case and adds the default block
to the switch. This will make the ioctl return -ENOTTY to user space (e.g.
setserial), which indicates that TIOCSSERIAL really isn't supported for
these devices currently.
Note that these (dummy) ioctl implementations where added by commit
2f430b4bba ("USB: ark3116: Add TIOCGSERIAL and TIOCSSERIAL ioctl
calls.") back in 2006. This in turn appears to have been triggered by a
change in a user space tool, wvdial, which started erroring out if
either was missing.
There are some bug reports about that against wvdial from around that
time, and looking at the wvstreams (library) code now, it looks like the
issue has indeed been resolved by handling errors more gracefully (e.g.
just logging them).
User space really should not make assumptions about these ioctl always
being implemented, but if this turns out to be a problem for anyone
using this driver, we'll add TIOCSSERIAL back in some form.
Signed-off-by: Mikhail Zaytsev <flashed@mail.ru>
[johan: amend commit message with backstory ]
Signed-off-by: Johan Hovold <johan@kernel.org>
This adds the ELV ALC 8xxx Battery Charging device
to the list of USB IDs of drivers/usb/serial/cp210x.c
Signed-off-by: Christian Holl <cyborgx1@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
According to drivers/usb/serial/io_edgeport.c, the driver may sleep
under a spinlock.
The function call path is:
edge_bulk_in_callback (acquire the spinlock)
process_rcvd_data
process_rcvd_status
change_port_settings
send_iosp_ext_cmd
write_cmd_usb
usb_kill_urb --> may sleep
To fix it, the redundant usb_kill_urb() is removed from the error path
after usb_submit_urb() fails.
This possible bug is found by my static analysis tool (DSAC) and checked
by my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
write_reg returns 0 on success, we can make it more explicit by returning
number 0 instead of result variable.
read_reg should return 0 on success since this is a more common pattern.
The user of read_reg has been clean-up and should be at the same commit.
Signed-off-by: Gimcuan Hui <gimcuan@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The assignment of DIV to itself is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Quectel BG96 is an Qualcomm MDM9206 based IoT modem, supporting both
CAT-M and NB-IoT. Tested hardware is BG96 mounted on Quectel
development board (EVB). The USB id is added to option.c to allow
DIAG,GPS,AT and modem communication with the BG96.
Signed-off-by: Sebastian Sjoholm <ssjoholm@mac.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along
with phy and chipidea enhancements. There's also a lot of SPDX tags
and license boilerplate cleanups as well, which provide some churn in
the diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see
happen.
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
usb: gadget: f_fs: Fix use-after-free in ffs_free_inst
USB: usbfs: compute urb->actual_length for isochronous
usb: core: message: remember to reset 'ret' to 0 when necessary
USB: typec: Remove remaining redundant license text
USB: typec: add SPDX identifiers to some files
USB: renesas_usbhs: rcar?.h: add SPDX tags
USB: chipidea: ci_hdrc_tegra.c: add SPDX line
USB: host: xhci-debugfs: add SPDX lines
USB: add SPDX identifiers to all remaining Makefiles
usb: host: isp1362-hcd: remove a couple of redundant assignments
USB: adutux: remove redundant variable minor
usb: core: add a new usb_get_ptm_status() helper
usb: core: add a 'type' parameter to usb_get_status()
usb: core: introduce a new usb_get_std_status() helper
usb: core: rename usb_get_status() 'type' argument to 'recip'
usb: core: add Status Type definitions
USB: gadget: Remove redundant license text
USB: gadget: function: Remove redundant license text
USB: gadget: udc: Remove redundant license text
USB: gadget: legacy: Remove redundant license text
...
