The hardware default uses management queue to transmit frames that are
downloaded into reserved page, so we need to clearly assign the frames
to use qsel in TX_DESC_QSEL_MGMT to avoid using wrong queue.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
DACK is done right after the hardware has been turned on, which
means it will be done every time we leave the IDLE state.
But it takes ~2 seconds to finish DACK.
We can back up the results and restore them. And it only takes a few
milliseconds to restore the results to the hardware, saving a lot of
time.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We could fail to power on because it was already on. If the return
value is -EALREADY, power off and then power on again to turn on the
hardware as expected.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
8822c used to count OFDM FA count by subtracting tx count from FA count.
But it need to substract more counters to be accurate.
However, we can count it by adding up all of the FA counters we want.
And it is simpler to add than list all of the components to substract.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver Could fail to reset counter if rx clock gating is not disabled.
So we need to disable rx clock gating before resetting counters.
Otherwise counters may increase unexpected.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In 2G channels, the cck source and rxagc should be set to different
values based on different bandwidth to increase the performance of rx
sensitivity.
To improve rx throughput performance, the values of sbd subtune and
pt_opt should be changed in different bandwidth.
Signed-off-by: Chien-Hsun Liao <ben.liao@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Collision of writing rf registers could occur if the driver writes
rf registers by direct write while the hardware is writing other rf
registers by pi write simultaneously.
Hardware pi write can be triggered by rf calibrations sometimes, so
the driver can not always write rf registers by direct write
protection. Direct write protection can make sure that there is no
hardware pi write during the direct write.
According to some experiments, if we add direct write protection
when switching channel, the performance of rf calibration will not
be affected.
Signed-off-by: Chien-Hsun Liao <ben.liao@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add beacon function setting routines for each hardware port.
If beacon function is not enabled, the hardware is not able
to synchronize with AP's beacon and can miss the beacons
under some scenarios such as PS mode.
For AP and Adhoc modes that require to send beacons, do not
update the TSF, otherwise the beacon interval may be affected.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When driver uses random mac address to scan, the unicast probe response
will not be received because the addr1 is not matched. Configure port
address by requested mac address to receive probe response from AP.
To support random mac scan, we need to configure the mac address during
scan period to receive unicast prop_resp. After scan is completed,
configure the mac address back to the original one that the port used.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With dynamic power save support, rtw88 is able to support fast tx
path, claim it to mac80211.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. This driver was saving the debugfs file away to be
removed at a later time. However, the 80211 core would delete the whole
directory that the debugfs files are created in, after it asks the
driver to do the deletion, so just rely on the 80211 core to do all of
the cleanup for us, making us not need to keep a pointer to the dentries
around at all.
This cleans up the structure of the driver data a bit and makes the code
a tiny bit smaller.
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. This driver was saving the debugfs file away to be
removed at a later time. However, the 80211 core would delete the whole
directory that the debugfs files are created in, after it asks the
driver to do the deletion, so just rely on the 80211 core to do all of
the cleanup for us, making us not need to keep a pointer to the dentries
around at all.
This cleans up the structure of the driver data a bit and makes the code
a tiny bit smaller.
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable rtstatus is being initialized with a value that is never read
as rtstatus is being re-assigned a little later on. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct ieee80211_regdomain {
...
struct ieee80211_reg_rule reg_rules[];
};
instance = kzalloc(sizeof(*mac->rd) +
sizeof(struct ieee80211_reg_rule) *
count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, reg_rules, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The assignment of 0 to variable k is never read once we break out of
the loop, so the assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable badworden is assigned with a value that is never read and
it is re-assigned a new value immediately afterwards. The assignment is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware can send invalid command response, the processing of
which can attempt to modify unexpected context and cause issues.
To fix this, driver should check that the command response ID is
same as the one it downloaded, and ignore processing of invalid
response.
Signed-off-by: Swati Kushwaha <swatiuma@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In set_mac_address, driver check for interfaces with same bss_type
For first STA entry, this would return 3 interfaces since all priv's have
bss_type as 0 due to kzalloc. Thus mac address gets changed for STA
unexpected. This patch adds check for first STA and avoids mac address
change. This patch also adds mac_address change for p2p based on bss_num
type.
Signed-off-by: Sharvari Harisangam <sharvari@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Unadorned '%p' has restrictive policies these days, such that it usually
just prints garbage at early boot (see
Documentation/core-api/printk-formats.rst, "kernel will print
``(ptrval)`` until it gathers enough entropy"). Annotating with %pK
(for "kernel pointer") allows the kptr_restrict sysctl to control
printing policy better.
We might just as well drop this message entirely, but this fix was easy
enough for now.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This message is pointless.
While we're at it, include the error code in the error message, which is
not pointless.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The syzbot fuzzer found a bug in the p54 USB wireless driver. The
issue involves a race between disconnect and the firmware-loader
callback routine, and it has several aspects.
One big problem is that when the firmware can't be loaded, the
callback routine tries to unbind the driver from the USB _device_ (by
calling device_release_driver) instead of from the USB _interface_ to
which it is actually bound (by calling usb_driver_release_interface).
The race involves access to the private data structure. The driver's
disconnect handler waits for a completion that is signalled by the
firmware-loader callback routine. As soon as the completion is
signalled, you have to assume that the private data structure may have
been deallocated by the disconnect handler -- even if the firmware was
loaded without errors. However, the callback routine does access the
private data several times after that point.
Another problem is that, in order to ensure that the USB device
structure hasn't been freed when the callback routine runs, the driver
takes a reference to it. This isn't good enough any more, because now
that the callback routine calls usb_driver_release_interface, it has
to ensure that the interface structure hasn't been freed.
Finally, the driver takes an unnecessary reference to the USB device
structure in the probe function and drops the reference in the
disconnect handler. This extra reference doesn't accomplish anything,
because the USB core already guarantees that a device structure won't
be deallocated while a driver is still bound to any of its interfaces.
To fix these problems, this patch makes the following changes:
Call usb_driver_release_interface() rather than
device_release_driver().
Don't signal the completion until after the important
information has been copied out of the private data structure,
and don't refer to the private data at all thereafter.
Lock udev (the interface's parent) before unbinding the driver
instead of locking udev->parent.
During the firmware loading process, take a reference to the
USB interface instead of the USB device.
Don't take an unnecessary reference to the device during probe
(and then don't drop it during disconnect).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+200d4bb11b23d929335f@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The lock protecting the data structure does not need to be an rwlock. The
only read access to the lock is in an error path, and if that's limiting
your scalability, you have bigger performance problems.
Eliminate mlx5_mkey_table in favour of using the xarray directly.
reg_mr_callback must use GFP_ATOMIC for allocating XArray nodes as it may
be called in interrupt context.
This also fixes a minor bug where SRCU locking was being used on the radix
tree read side, when RCU was needed too.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch adds reference counting support for
alloc/free mac filters
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds TCAM reference counting
support for cxgb4 change mac path
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds TCAM reference counting
support for raw mac filters.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove existing mps refcounting code which was
added only for encap filters and add necessary
data structures/functions to support mps reference
counting for all the mac filters. Also add wrapper
functions for allocating and freeing encap mac
filters.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently arch/mips/include/asm/io.h provides 64b memory accessor
functions such as readq & writeq even on MIPS32 platforms where those
accessors cannot actually perform a 64b memory access. They instead
BUG(). This is unfortunate for drivers which either #ifdef on the
presence of these accessors, or can function with non-atomic
implementations of them found in either linux/io-64-nonatomic-lo-hi.h or
linux/io-64-nonatomic-hi-lo.h. As such we're preparing to remove the
definitions of these 64b accessor functions for MIPS32 kernels.
In preparation for this, include linux/io-64-nonatomic-lo-hi.h in
defza.c in order to provide a non-atomic implementation of the
readq_relaxed & writeq_relaxed functions that are used by this code. In
practice this will have no runtime effect, since use of the 64b accessor
functions is conditional upon sizeof(unsigned long) == 8, ie. upon
CONFIG_64BIT=y. This means the calls to these non-atomic readq & writeq
implementations will be optimized out anyway, but we need their
definitions to keep the compiler happy.
For 64bit kernels using this code this change should also have no effect
because asm/io.h will continue to provide the definitions of
readq_relaxed & writeq_relaxed, which linux/io-64-nonatomic-lo-hi.h
checks for before defining itself.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Serge Semin <Sergey.Semin@t-platforms.ru>
Cc: netdev@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
The PHY selection bit also exists on SoCs without an internal PHY; if it's
set to 1 (internal PHY, default value) then the MAC will not make use of
any PHY on such SoCs.
This problem appears when adapting for H6, which has no real internal PHY
(the "internal PHY" on H6 is not on-die, but on a co-packaged AC200 chip,
connected via RMII interface at GPIO bank A).
Force the PHY selection bit to 0 when the SOC doesn't have an internal PHY,
to address the problem of a wrong default value.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EMAC on Allwinner H6 is just like the one on A64. The "internal PHY" on
H6 is on a co-packaged AC200 chip, and it's not really internal (it's
connected via RMII at PA GPIO bank).
Add support for the Allwinner H6 EMAC in the dwmac-sun8i driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The syzbot reported
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xca/0x13e lib/dump_stack.c:113
print_address_description+0x67/0x231 mm/kasan/report.c:188
__kasan_report.cold+0x1a/0x32 mm/kasan/report.c:317
kasan_report+0xe/0x20 mm/kasan/common.c:614
qmi_wwan_probe+0x342/0x360 drivers/net/usb/qmi_wwan.c:1417
usb_probe_interface+0x305/0x7a0 drivers/usb/core/driver.c:361
really_probe+0x281/0x660 drivers/base/dd.c:509
driver_probe_device+0x104/0x210 drivers/base/dd.c:670
__device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454
Caused by too many confusing indirections and casts.
id->driver_info is a pointer stored in a long. We want the
pointer here, not the address of it.
Thanks-to: Hillf Danton <hdanton@sina.com>
Reported-by: syzbot+b68605d7fadd21510de1@syzkaller.appspotmail.com
Cc: Kristian Evensen <kristian.evensen@gmail.com>
Fixes: e4bf63482c ("qmi_wwan: Add quirk for Quectel dynamic config")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the macb driver to use NAPI GRO helpers when
receiving SKBs. This improves performances.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use NAPI_POLL_WEIGHT, the default NAPI poll() weight instead of
redefining our own value (which turns out to be 64 as well).
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the MAC address setup in the probe. The MAC address
retrieved using of_get_mac_address was checked for not containing an
error, but it may also be NULL which wasn't tested. Fix it by replacing
IS_ERR with IS_ERR_OR_NULL.
Fixes: 541ddc66d6 ("net: macb: support of_get_mac_address new ERR_PTR error")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend macros MLXSW_REG_MTMP_TEMP_TO_MC() to allow support of negative
temperature readout, since chip and others thermal components are
capable of operating within the negative temperature.
With no such support negative temperature will be consider as very high
temperature and it will cause wrong readout and thermal shutdown.
For negative values 2`s complement is used.
Tested in chamber.
Example of chip ambient temperature readout with chamber temperature:
-10 Celsius:
temp1: -6.0C (highest = -5.0C)
-5 Celsius:
temp1: -1.0C (highest = -1.0C)
v2 (Andrew Lunn):
* Replace '%u' with '%d' in mlxsw_hwmon_module_temp_show()
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When multiple sensors are mapped to the same cooling device, the
cooling device should be set according the worst sensor from the
sensors associated with this cooling device.
Provide the hottest thermal zone detection and enforce cooling device
to follow the temperature trends of the hottest zone only.
Prevent competition for the cooling device control from others zones,
by "stable trend" indication. A cooling device will not perform any
actions associated with a zone with a "stable trend".
When other thermal zone is detected as a hottest, a cooling device is
to be switched to following temperature trends of new hottest zone.
Thermal zone score is represented by 32 bits unsigned integer and
calculated according to the next formula:
For T < TZ<t><i>, where t from {normal trip = 0, high trip = 1, hot
trip = 2, critical = 3}:
TZ<i> score = (T + (TZ<t><i> - T) / 2) / (TZ<t><i> - T) * 256 ** j;
Highest thermal zone score s is set as MAX(TZ<i>score);
Following this formula, if TZ<i> is in trip point higher than TZ<k>,
the higher score is to be always assigned to TZ<i>.
For two thermal zones located at the same kind of trip point, the higher
score will be assigned to the zone which is closer to the next trip
point. Thus, the highest score will always be assigned objectively to
the hottest thermal zone.
All the thermal zones initially are to be configured with mode
"enabled" with the "step_wise" governor.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a dedicated thermal zone for each inter-connect device. The
current temperature is obtained from inter-connect temperature sensor
and the default trip points are set to the same values as default ASIC
trip points. These settings could be changed from the user space.
A cooling device (fan) is bound to all inter-connect devices.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bfe59032bd ("net: ethernet:
ti: cpsw: use cpsw as drv data")changes
the driver data to struct cpsw_common *cpsw. This is done
only in probe/remove but the suspend/resume functions are
still left with struct net_device *ndev. Hence fix both
suspend & resume also to fetch the updated driver data.
Fixes: bfe59032bd ("net: ethernet: ti: cpsw: use cpsw as drv data")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implement the statistical interface of ethtool, user can use
ethtool -S to show hinic statistics.
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 22000 series FW that was meant to be used with hr is
also the FW that is used for hr1 and has a different RF ID.
Add support to load the hr FW when hr1 RF ID is detected.
Cc: stable@vger.kernel.org # 5.1+
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Per the 802.11 specification, vendor IEs are (at minimum) only required
to contain an OUI. A type field is also included in ieee80211.h (struct
ieee80211_vendor_ie) but doesn't appear in the specification. The
remaining fields (subtype, version) are a convention used in WMM
headers.
Thus, we should not reject vendor-specific IEs that have only the
minimum length (3 bytes) -- we should skip over them (since we only want
to match longer IEs, that match either WMM or WPA formats). We can
reject elements that don't have the minimum-required 3 byte OUI.
While we're at it, move the non-standard subtype and version fields into
the WMM structs, to avoid this confusion in the future about generic
"vendor header" attributes.
Fixes: 685c9b7750 ("mwifiex: Abort at too short BSS descriptor element")
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For tx path, in most cases, we still have to take refcnt on the dst
cause the caller is caching the dst somewhere. But it still is
beneficial to make use of RT6_LOOKUP_F_DST_NOREF flag while doing the
route lookup. It is cause this flag prevents manipulating refcnt on
net->ipv6.ip6_null_entry when doing fib6_rule_lookup() to traverse each
routing table. The null_entry is a shared object and constant updates on
it cause false sharing.
We converted the current major lookup function ip6_route_output_flags()
to make use of RT6_LOOKUP_F_DST_NOREF.
Together with the change in the rx path, we see noticable performance
boost:
I ran synflood tests between 2 hosts under the same switch. Both hosts
have 20G mlx NIC, and 8 tx/rx queues.
Sender sends pure SYN flood with random src IPs and ports using trafgen.
Receiver has a simple TCP listener on the target port.
Both hosts have multiple custom rules:
- For incoming packets, only local table is traversed.
- For outgoing packets, 3 tables are traversed to find the route.
The packet processing rate on the receiver is as follows:
- Before the fix: 3.78Mpps
- After the fix: 5.50Mpps
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a no-op that simply moves all locking and unlocking of
->reg_lock into trivial helpers. I did that to be able to easily add
some ad hoc instrumentation to those helpers to get some information
on contention and hold times of the mutex. Perhaps others want to do
something similar at some point, so this frees them from doing the
'sed -i' yoga, and have a much smaller 'git diff' while fiddling.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
