The ADIN1300 chip supports RGMII, RMII & MII modes. Default (if
unconfigured) is RGMII.
This change adds support for configuring these modes via the device
registers.
For RGMII with internal delays (modes RGMII_ID,RGMII_TXID, RGMII_RXID),
the default delay is 2 ns. This can be configurable and will be done in
a subsequent change.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both ADIN1200 & ADIN1300 support Clause 45 access for some registers.
The Extended Management Interface (EMI) registers are accessible via both
Clause 45 (at register MDIO_MMD_VEND1) and using Clause 22.
The Clause 22 access for MMD regs differs from the standard one defined by
802.3. The ADIN PHYs use registers ExtRegPtr (0x0010) and ExtRegData
(0x0011) to access Clause 45 & EMI registers.
The indirect access is done via the following mechanism (for both R/W):
1. Write the address of the register in the ExtRegPtr
2. Read/write the value of the register via reg ExtRegData
This mechanism is needed to manage configuration of chip settings and to
access EEE registers via Clause 22.
Since Clause 45 access will likely never be used, it is not implemented via
this hook.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds support for Analog Devices Industrial Ethernet PHYs.
Particularly the PHYs this driver adds support for:
* ADIN1200 - Robust, Industrial, Low Power 10/100 Ethernet PHY
* ADIN1300 - Robust, Industrial, Low Latency 10/100/1000 Gigabit
Ethernet PHY
The 2 chips are register compatible with one another. The main difference
being that ADIN1200 doesn't operate in gigabit mode.
The chips can be operated by the Generic PHY driver as well via the
standard IEEE PHY registers (0x0000 - 0x000F) which are supported by the
kernel as well. This assumes that configuration of the PHY has been done
completely in HW, according to spec.
Configuration can also be done via registers, which will be supported by
this driver.
Datasheets:
https://www.analog.com/media/en/technical-documentation/data-sheets/ADIN1300.pdfhttps://www.analog.com/media/en/technical-documentation/data-sheets/ADIN1200.pdf
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for PTP Hardware Clock (PHC) to the Ocelot
switch for both PTP 1-step and 2-step modes.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In struct frame_info, the cpuq member is never used. This cosmetic patch
removes it from the structure, and from the parsing of the frame header
as it's only set but never used.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cosmetic patch improves the frame header parsing readability by
introducing a new macro to access and mask its fields.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for using the PTP register range, and adds a
description of its registers. This bank is used when configuring PTP.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver interface for reading the config attributes from user
provided buffer, and updates these values on nvm config flash partition.
This is basically an expansion of our existing ethtool -f implementation.
The management FW has exposed an additional method of configuring some of
the nvram options, and this makes use of that. This implementation will
come into use when newer FW files which contain configuration directives
employing this API will be provided to ethtool -f.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds API for configuring the NVM config attributes using
Management FW (MFW) interfaces.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In myri10ge_probe(), myri10ge_alloc_slices() is invoked to allocate slices
related structures. Later on, myri10ge_request_irq() is used to get an irq.
However, if this process fails, the allocated slices related structures are
not deallocated, leading to memory leaks. To fix this issue, revise the
target label of the goto statement to 'abort_with_slices'.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
pull-request: can-next 2019-08-14
this is a pull request for net-next/master consisting of 41 patches.
The first two patches are for the kvaser_pciefd driver: Christer Beskow
removes unnecessary code in the kvaser_pciefd_pwm_stop() function,
YueHaibing removes the unused including of <linux/version.h>.
In the next patch YueHaibing also removes the unused including of
<linux/version.h> in the f81601 driver.
In the ti_hecc driver the next 6 patches are by me and fix checkpatch
warnings. YueHaibing's patch removes an unused variable in the
ti_hecc_mailbox_read() function.
The next 6 patches all target the xilinx_can driver. Anssi Hannula's
patch fixes a chip start failure with an invalid bus. The patch by
Venkatesh Yadav Abbarapu skips an error message in case of a deferred
probe. The 3 patches by Appana Durga Kedareswara rao fix the RX and TX
path for CAN-FD frames. Srinivas Neeli's patch fixes the bit timing
calculations for CAN-FD.
The next 12 patches are by me and several checkpatch warnings in the
af_can, raw and bcm components.
Thomas Gleixner provides a patch for the bcm, which switches the timer
to HRTIMER_MODE_SOFT and removes the hrtimer_tasklet.
Then 6 more patches by me for the gw component, which fix checkpatch
warnings, followed by 2 patches by Oliver Hartkopp to add CAN-FD
support.
The vcan driver gets 3 patches by me, fixing checkpatch warnings.
And finally a patch by Andre Hartmann to fix typos in CAN's netlink
header.
====================
If oct->fn_list.enable_io_queues() fails, no cleanup is executed, leading
to memory/resource leaks. To fix this issue, invoke
octeon_delete_instr_queue() before returning from the function.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
compile-testing this driver on other architectures showed
multiple warnings:
drivers/net/ethernet/nxp/lpc_eth.c: In function 'lpc_eth_drv_probe':
drivers/net/ethernet/nxp/lpc_eth.c:1337:19: warning: format '%d' expects argument of type 'int', but argument 4 has type 'resource_size_t {aka long long unsigned int}' [-Wformat=]
drivers/net/ethernet/nxp/lpc_eth.c:1342:19: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]
Use format strings that work on all architectures.
Link: https://lore.kernel.org/r/20190809144043.476786-10-arnd@arndb.de
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
drivers/net/ethernet/nxp/lpc_eth.c:1316:31-32: WARNING comparing pointer to 0
Compare pointer-typed values to NULL rather than 0
Semantic patch information:
This makes an effort to choose between !x and x == NULL. !x is used
if it has previously been used with the function used to initialize x.
This relies on type information. More type information can be obtained
using the option -all_includes and the option -I to specify an
include path.
Generated by: scripts/coccinelle/null/badzero.cocci
Link: https://lore.kernel.org/r/20190809144043.476786-9-arnd@arndb.de
Fixes: e42016eb3844 ("net: lpc-enet: allow compile testing")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Setting the phy mode requires touching a platform specific
register, which prevents us from building the driver without
its header files.
Move it into a separate function in arch/arm/mach/lpc32xx
to hide the core registers from the network driver.
Link: https://lore.kernel.org/r/20190809144043.476786-8-arnd@arndb.de
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The lpc_eth driver uses a platform specific method to find
the internal sram. This prevents building it on other machines.
Rework to only use one function call and keep the other platform
internals where they belong. Ideally this would look up the
sram location from DT, but as this is a rarely used driver,
I want to keep the modifications to a minimum.
Link: https://lore.kernel.org/r/20190809144043.476786-7-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Implement dummy region of size 32K and allow user to create snapshots
or random data using debugfs file trigger.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync EEE init for RTL8168h with vendor driver and add two writes to
vendor-specific registers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the Realtek PHY driver maps the vendor-specific EEE registers
to the standard MMD registers, we can remove all special handling and
use the generic functions phy_ethtool_get/set_eee.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEE-related registers on newer integrated PHY's have the standard
layout, but are accessible not via MMD but via vendor-specific
registers. Emulating the standard MMD registers allows to use the
generic functions for EEE control.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cited patch deleted ethtool flash device support, as ethtool core can
fallback into devlink flash callback. However, this is supported only if
there is a devlink port registered over the corresponding netdevice.
As mlx5e do not have devlink port support over native netdevice, it broke
the ability to flash device via ethtool.
This patch re-add the ethtool callback to avoid user functionality breakage
when trying to flash device via ethtool.
Fixes: 9c8bca2637 ("mlx5: Move firmware flash implementation to devlink")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add a missing spinlock around XSKICOSQ usage at the activation stage,
because there is a race between a configuration change and the
application calling sendto().
Fixes: db05815b36 ("net/mlx5e: Add XSK zero-copy support")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When the genphy driver binds to a swphy it will call
genphy_read_abilites that will try to read MII_ESTATUS if BMSR_ESTATEN
is set in MII_BMSR. So far this would read the default value 0xffff
and 1000FD and 1000HD are reported as supported just by chance.
Better add explicit support for emulating MII_ESTATUS.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Value of MII_CTRL1000 is needed only if LPA_1000MSFAIL is set.
Therefore move reading this register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In blocked_fl_write(), 't' is not deallocated if bitmap_parse_user() fails,
leading to a memory leak bug. To fix this issue, free t before returning
the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_done_tasklet tasklet is used in invoke the hrtimer
(mvpp2_hr_timer_cb) in softirq context. This can be also achieved without
the tasklet but with HRTIMER_MODE_SOFT as hrtimer mode.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek provided information on how the new NIC-integrated PHY's
expose whether they support 2.5G/5G/10G. This allows to automatically
differentiate 1Gbps and 2.5Gbps PHY's, and therefore allows to
remove the fake PHY ID mechanism for RTL8125.
So far RTL8125 supports 2.5Gbps only, but register layout for faster
modes has been defined already, so let's use this information to be
future-proof.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Holger reported sporadic transmit timeouts and it turned out that one
path misses ringing the doorbell. Fix was suggested by Eric.
Fixes: ef14358546 ("r8169: make use of xmit_more")
Suggested-by: Eric Dumazet <edumazet@google.com>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After configuring and restarting aneg we immediately try to read the
link status. On some systems the PHY may not yet have cleared the
"aneg complete" and "link up" bits, resulting in a false link-up
signal. See [0] for a report.
Clause 22 and 45 both require the PHY to keep the AN_RESTART
bit set until the PHY actually starts auto-negotiation.
Let's consider this in the generic functions for reading link status.
The commit marked as fixed is the first one where the patch applies
cleanly.
[0] https://marc.info/?t=156518400300003&r=1&w=2
Fixes: c1164bb1a6 ("net: phy: check PMAPMD link status only in genphy_c45_read_link")
Tested-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
In mlx4_en_config_rss_steer(), 'rss_map->indir_qp' is allocated through
kzalloc(). After that, mlx4_qp_alloc() is invoked to configure RSS
indirection. However, if mlx4_qp_alloc() fails, the allocated
'rss_map->indir_qp' is not deallocated, leading to a memory leak bug.
To fix the above issue, add the 'qp_alloc_err' label to free
'rss_map->indir_qp'.
Fixes: 4931c6ef04 ("net/mlx4_en: Optimized single ring steering")
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The ibm,mac-address-filters property defines the maximum number of
addresses the hypervisor's multicast filter list can support. It is
encoded as a big-endian integer in the OF device tree, but the virtual
ethernet driver does not convert it for use by little-endian systems.
As a result, the driver is not behaving as it should on affected systems
when a large number of multicast addresses are assigned to the device.
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use skb_add_rx_frag() to reduce the memory copy for rx data.
Use a new list of rx_used to store the rx buffer which couldn't be
reused yet.
Besides, the total number of rx buffer may be increased or decreased
dynamically. And it is limited by RTL8152_MAX_RX_AGG.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The original method uses an array to store the rx information. The
new one uses a list to link each rx structure. Then, it is possible
to increase/decrease the number of rx structure dynamically.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The different chips may accept different rx buffer sizes. The RTL8152
supports 16K bytes, and RTL8153 support 32K bytes.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
So far phy_speed_down/up can be used up to 1Gbps only. Remove this
restriction by using new helper __phy_speed_down. New member adv_old
in struct phy_device is used by phy_speed_up to restore the advertised
modes before calling phy_speed_down. Don't simply advertise what is
supported because a user may have intentionally removed modes from
advertisement.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
phy_speed_down_core provides most of the functionality for
phy_speed_down. It makes use of new helper phy_resolve_min_speed that is
based on the sorting of the settings[] array. In certain cases it may be
helpful to be able to exclude legacy half duplex modes, therefore
prepare phy_resolve_min_speed() for it.
v2:
- rename __phy_speed_down to phy_speed_down_core
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
We will need the functionality of __set_linkmode_max_speed also for
linkmode bitmaps other than phydev->supported. Therefore split it.
v2:
- remove unused parameter from __set_linkmode_max_speed
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Fix sparse warning:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:3190:5:
warning: symbol 'hclge_func_reset_sync_vf' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Merging tip of mlx5-next in order to get changes related to adding
XRQ support to the DEVX interface needed prior to the following two
patches.
Signed-off-by: Doug Ledford <dledford@redhat.com>
For CANFD 2.0 IP configuration existing driver is using incorrect mask
values for FSR register FL and RI fields.
Fixes: c223da6 ("can: xilinx_can: Add support for CANFD FD frames")
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Acked-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
