Fix typo setting urb->transfer_buffer_length in mt76u_fill_rx_sg
Fixes: b40b15e152 ("mt76: add usb support to mt76 layer")
Fixes: f8f527b16d ("mt76: usb: use EP max packet aligned buffer sizes for rx")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
- Store the previous and current rate set in the driver + the TSF value
at the time of the switch.
- Use the tx status TSF value to determine which rate set needs to be used
as reference.
- Report only short or long GI rates for a single status event, not a mix.
- The hardware reports the last used rate index. Use it along with the
retry count to figure out what rate was used for the first attempt.
- Use the same retry count value for all rate slots to make this calculation
work.
- Derive the probe rate from the current rateset instead of the skb cb
- Do not wait for a status report for the probe frame before removing the
probe rate from the rate table. Do it immediately after it was referenced
in a tx status report.
- Use the first half of the first rate retry budget for the probe rate
in order to avoid using too many retries on that rate
- Switch from lower rates to higher rates more conservatively
- enable hardware rate up/down selection
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
These values must be initialized to zero, otherwise the hardware could
reuse previous values, especially the rate index
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It bypasses the MCU, so it does not belong in mcu.c
Also make mt7615_mac_tx_rate_val static
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt7615_mcu_send_ram_firmware routine since mt7615_load_ram runs the
same code to send ram firmware to cr4 and n9 mcus. Moreover rename
gen_dl_mode in mt7615_mcu_gen_dl_mode.
This patch does not introduce any behaviour change, it is just code
refactor.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Release patch semaphore even if request_firmware fails in
mt7615_load_patch
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since we don't clean that tx queue from the tx tasklet, we need to do it
after the firmware upload is done. This patch also adds a cleanup step during
the upload, to help reclaim memory faster.
Fixes unprocessed queued frames eating up memory long after the firmware
upload has already completed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_mcu_rdd_send_pattern routine to trigger a radar pattern
detection. Moreover move debugfs related routines in a dedicated source
file.
Suggested-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add Channel Switch Announcement support to mt7615 driver updating beacon
template with CSA IE received from mac80211
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Delay channel calibration after Channel Availability Check. Add some
code cleanup to mt7615_mcu_set_channel
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add hw radar detection support to mt7615 driver in order to
unlock dfs channels on 5GHz band
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_regd_notifier callback. This is a preliminary patch to
add radar detection support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the following sparse warning in __mt7615_mcu_msg_send:
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c:78:15: sparse: warning:
restricted __le16 degrades to integer
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c:78:15: sparse: warning:
cast from restricted __le16
Fixes: 04b8e65922 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When beacon length is not a multiple of 4, the beacon could be sent with
the last 1-3 bytes corrupted. The skb data is guaranteed to have enough
room for reading beyond the end, because it is always followed by
skb_shared_info, so rounding up is safe.
All other callers of mt76_wr_copy have multiple-of-4 length already.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ice_parse_caps is printing capabilities in a different way when
compared to the variable names. This makes it difficult to search for
the right strings in the debug logs. So this patch updates the
print strings to be exactly the same as the fields' name in the
structure.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver should start out with a reasonable number of descriptors that
can prevent drops due to a CPU being in a power management state.
Change the default number of descriptors to 2048.
The user can always change the value at runtime. Transmit descriptor
counts are not modified because they don't need to change due to the
speed of the interface, or for power managed CPUs, but the code is
simplified to a fixed value for the transmit default.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove q_left_tx and q_left_rx from the PF struct as these can be
obtained by calling ice_get_avail_txq_count and ice_get_avail_rxq_count
respectively.
The function ice_determine_q_usage is only setting num_lan_tx and
num_lan_rx in the PF structure, and these are later assigned to
vsi->alloc_txq and vsi->alloc_rxq respectively. This is an unnecessary
indirection, so remove ice_determine_q_usage and just assign values
for vsi->alloc_txq and vsi->alloc_rxq in ice_vsi_set_num_qs and use
these to set num_lan_tx and num_lan_rx respectively.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an additional boolean parameter to the ice_init_dcb
function. This boolean controls if the LLDP MIB change
events are registered for. Also, add a new function
defined ice_cfg_lldp_mib_change. The additional function
is necessary to be able to register for LLDP MIB change
events after calling ice_init_dcb. The net effect of these
two changes is to allow a delayed registration for MIB change
events so that the driver is not accepting events before it
is ready for them.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes how and when the driver report link status, instead of
waiting till the call to enable queues for VF, we should report link
status earlier with opcode to get VF resources - So as to avoid reporting
erroneous information, especially when queues have not been configured.
In addition, we can also make a call to get and report link status change
after when queue is enabled, at least to report netdev or PHY link status.
This is in accordance to how link speed is being reported for PF...
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is port of a fix from i40e commit 2ad1274fa3 ("i40e: don't
report link up for a VF who hasn't enabled queues")
Older VF drivers do not respond well to receiving a link
up notification before queues are enabled. This can cause their state
machine to think that it is safe to send traffic. This results in a Tx
hang on the VF.
Record whether the PF has actually enabled queues for the VF. When
reporting link status, always report link down if the queues aren't
enabled. In this way, the VF driver will never receive a link up
notification until after its queues are enabled.
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a PFR (or bigger reset) occurs, the device clears the VF_MBX_ARQLEN
register for all VFs. But if a VFR is triggered by a VF, the device does
NOT clear this register, and the VF driver will never see the reset.
When this happens, the VF driver will eventually timeout and attempt
recovery, and usually it will be successful. But this makes resets take
a long time and there are occasional failures.
We cannot just blithely clear this register on every reset; this has
been shown to cause synchronization problems when a PFR is triggered
with a large number of VFs.
Fix this by clearing VF_MBX_ARQLEN when the reset source is not PFR.
GlobR will trigger PFR, so this test catches that occurrence as well.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver has supported a transmit work limit
that was configurable from ethtool for a long time, but
there are no good use cases for having it be a variable
that can be changed at run time. In addition, this
variable was noted to be causing performance overhead
due to cache misses.
Just remove the variable and let the code use a constant
so that the functionality is maintained (a limit on the
number of transmits that will be cleaned in any one call
to the clean routines) without the cache miss.
Removes code, removes a variable, removes testing surface. Yay.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a small bit of efficiency to the code by adding a
prefetch of the port_info structure in order to help
avoid a cache miss a little later on in execution.
Also add an unlikely statement to a branch which
generally will never happen in normal operation.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a simple patch to move the assignment to a local variable
closer to the site where the local variable is used. This
can help readability and also maybe performance, although the
performance enhancement is really dependent upon the compiler.
No functional change.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are a couple of functions that don't need two arguments
passed in when the second argument already had access to
the pointer pointed to by the first.
Remove the unnecessary arguments.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are multiple places where we currently use ice_find_vsi_by_type
to get the PF (a.k.a. main) VSI. The PF VSI by definition is always
the first element in the pf->vsi array (i.e. pf->vsi[0]). So instead
add and use a new helper function ice_get_main_vsi, which just returns
pf->vsi[0].
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when vsi->req_txqs or vsi->req_rxqs are set we don't
correctly set the number of vsi->num_q_vectors. Fix this by
setting the number of queue vectors based on the max
between the vsi->alloc_txqs and vsi->alloc_rxqs.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, we don't add headroom to the handle in ixgbe_zca_free,
ixgbe_alloc_buffer_slow_zc and ixgbe_alloc_buffer_zc. The addition of the
headroom to the handle was removed in
commit d8c3061e5e ("ixgbe: modify driver for handling offsets"), which
will break things when headroom isvnon-zero. This patch fixes this and uses
xsk_umem_adjust_offset to add it appropritely based on the mode being run.
Fixes: d8c3061e5e ("ixgbe: modify driver for handling offsets")
Reported-by: Bjorn Topel <bjorn.topel@intel.com>
Signed-off-by: Kevin Laatz <kevin.laatz@intel.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Currently, we don't add headroom to the handle in i40e_zca_free,
i40e_alloc_buffer_slow_zc and i40e_alloc_buffer_zc. The addition of the
headroom to the handle was removed in
commit 2f86c806a8 ("i40e: modify driver for handling offsets"), which
will break things when headroom is non-zero. This patch fixes this and uses
xsk_umem_adjust_offset to add it appropritely based on the mode being run.
Fixes: 2f86c806a8 ("i40e: modify driver for handling offsets")
Reported-by: Bjorn Topel <bjorn.topel@intel.com>
Signed-off-by: Kevin Laatz <kevin.laatz@intel.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The UPS feature only works for runtime suspend, so UPS flags only
need to be set before enabling runtime suspend. Therefore, I create
a struct to record relative information, and use it before runtime
suspend.
All chips could record such information, even though not all of
them support the feature of UPS. Then, some functions could be
combined.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the static keyword to the front of declaration of g_dsaf_mode_match,
and resolve the following compiler warning that can be seen when building
with warnings enabled (W=1):
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:27:1: warning:
‘static’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the static keyword to the front of declaration of iwarp_state_names,
and resolve the following compiler warning that can be seen when building
with warnings enabled (W=1):
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:385:1: warning:
‘static’ is not at beginning of declaration [-Wold-style-declaration]
Also, resolve checkpatch.pl script warning:
WARNING: static const char * array should probably be
static const char * const
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Acked-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use set/get drv data in phydev's mdio device instead. Phy device priv
field maybe used by the external phy driver and should not be
overwritten.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Historically, gianfar only used phy-connection-type DT property when
connected to PHY in the rgmii-id mode. It ignored the property otherwise,
relying on the connection type auto-detection carried out by MAC and
providing that reconstructed mode to of_phy_connect(). It also did not
consider alternative phy-mode property at all.
Make the driver properly query DT node for PHY connection type first and
use an obtained value if it was specified there. Otherwise, if a particular
DT relies on connection type auto-detection, fall back to reconstructing
the value from MAC registers, as before.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove now unused macro and structure definitions from gianfar.h that have
accumulated there over time.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make functions that do not have callers outside the translation unit they
are defined in static.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove forward declarations of various static functions located in two
driver implementation files and rearrange the corresponding definitions
accordingly.
This patch only introduces mechanical changes, namely it removes forward
declarations and moves function definitions around; it does not change any
functionality.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test to validate the Jumbo Frame support in stmmac in single
channel and multichannel mode.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are already doing it by default in the TX path so we can also enable
Jumbo Frame support in the RX path independently of MTU value.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maximum MTU for XGMAC cores is 16k thus the check for presence of XGMAC
shall be done first in order to assign correct value.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RAVSEL means that only RX side is available for AVB features. As we use
both TX and RX features we need to check if RAVSEL is selected and
disable AVB if only RX side is available.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RX Watchdog is disabled its currently not possible to configure TX
coalesce settings. Let user configure it anyway.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only consider that we have an error when HW Timestamping is not enabled
as this can give false positives due to the fact the RX Timestamping in
XGMAC and GMAC cores comes from context descriptors.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
