Currently rt2x00 devices retransmit the management frames with
incremented sequence number if hardware is assigning the sequence.
This is HW bug fixed already for non-QOS data frames, but it should
be fixed for management frames except beacon.
Without fix retransmitted frames have wrong SN:
AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1648, FN=0, Flags=........C Frame is not being retransmitted 1648 1
AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1649, FN=0, Flags=....R...C Frame is being retransmitted 1649 1
AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1650, FN=0, Flags=....R...C Frame is being retransmitted 1650 1
With the fix SN stays correctly the same:
88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=........C
88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=....R...C
88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=....R...C
Cc: stable@vger.kernel.org
Signed-off-by: Vijayakumar Durai <vijayakumar.durai1@vivint.com>
[sgruszka: simplify code, change comments and changelog]
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Now that the sequence number allocation is fixed, we can finally send a BAR
at powersave wakeup time to refresh the receiver side reorder window
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the MT_TXD3_SN_VALID flag is not set in the tx descriptor, the hardware
assigns the sequence number. However, the rest of the code assumes that the
sequence number specified in the 802.11 header gets transmitted.
This was causing issues with the aggregation setup, which worked for the
initial one (where the sequence numbers were still close), but not for
further teardown/re-establishing of sessions.
Additionally, the overwrite of the TID sequence number in WTBL2 was resetting
the hardware assigned sequence numbers, causing them to drift further apart.
Fix this by using the software assigned sequence numbers
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently there is no way for the driver to signal to mac80211 that it should
schedule a TXQ even if there are no packets on the mac80211 part of that queue.
This is problematic if the driver has an internal retry queue to deal with
software A-MPDU retry.
This patch changes the behavior of ieee80211_schedule_txq to always schedule
the queue, as its only user (ath9k) seems to expect such behavior already:
it calls this function on tx status and on powersave wakeup whenever its
internal retry queue is not empty.
Also add an extra argument to ieee80211_return_txq to get the same behavior.
This fixes an issue on ath9k where tx queues with packets to retry (and no
new packets in mac80211) would not get serviced.
Fixes: 89cea7493a ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we just set this to 2048, and have multiple limits you
can select from, the total number might run over and cause
a warning in cfg80211. This doesn't make sense, so we just
calculate the total max_interfaces now.
Reported-by: syzbot+8f91bd563bbff230d0ee@syzkaller.appspotmail.com
Fixes: 99e3a44bac ("mac80211_hwsim: allow setting iftype support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
size = struct_size(instance, entry, count);
or
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)
Based on the above, replace qtnf_cmd_acl_data_size() with the
new struct_size() helper.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case dev_alloc_skb fails, the fix safely returns to avoid
potential NULL pointer dereference.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case alloc_workqueue fails, the fix reports the error and
returns to avoid NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Smatch complains that "local_rx_pd->priority" can't be trusted because
it comes from skb->data and it can go up to 255 instead of being capped
in the 0-7 range. A few lines earlier, on the other side of the if
statement, we cap priority so it seems harmless to add a bounds check
here as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'hostcmd' is alloced by kzalloc, should be freed before
leaving from the error handling cases, otherwise it will
cause mem leak.
Fixes: 3935ccc14d ("mwifiex: add cfg80211 testmode support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case dev_alloc_skb fails, the fix returns -ENOMEM to avoid
NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently 1 is being assigned to *res and then it is immediately
updated with the computed result. The first assignment is
redundant and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clang warns about what is clearly a case of passing an uninitalized
variable into a static function:
drivers/net/wireless/broadcom/b43/phy_lp.c:1852:23: error: variable 'gains' is uninitialized when used here
[-Werror,-Wuninitialized]
lpphy_papd_cal(dev, gains, 0, 1, 30);
^~~~~
drivers/net/wireless/broadcom/b43/phy_lp.c:1838:2: note: variable 'gains' is declared here
struct lpphy_tx_gains gains, oldgains;
^
1 error generated.
However, this function is empty, and its arguments are never evaluated,
so gcc in contrast does not warn here. Both compilers behave in a
reasonable way as far as I can tell, so we should change the code
to avoid the warning everywhere.
We could just eliminate the lpphy_papd_cal() function entirely,
given that it has had the TODO comment in it for 10 years now
and is rather unlikely to ever get done. I'm doing a simpler
change here, and just pass the 'oldgains' variable in that has
been initialized, based on the guess that this is what was
originally meant.
Fixes: 2c0d6100da ("b43: LP-PHY: Begin implementing calibration & software RFKILL support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case kmemdup fails, the fix sets conn_info->req_ie_len and
conn_info->resp_ie_len to zero to avoid buffer overflows.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmf_usb_free_q is no longer called with pending=true thus this boolean
parameter is no longer needed.
Signed-off-by: Piotr Figiel <p.figiel@camlintechnologies.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It was observed that rarely during USB disconnect happening shortly after
connect (before full initialization completes) usb_hub_wq would wait
forever for the dev_init_lock to be unlocked. dev_init_lock would remain
locked though because of infinite wait during usb_kill_urb:
[ 2730.656472] kworker/0:2 D 0 260 2 0x00000000
[ 2730.660700] Workqueue: events request_firmware_work_func
[ 2730.664807] [<809dca20>] (__schedule) from [<809dd164>] (schedule+0x4c/0xac)
[ 2730.670587] [<809dd164>] (schedule) from [<8069af44>] (usb_kill_urb+0xdc/0x114)
[ 2730.676815] [<8069af44>] (usb_kill_urb) from [<7f258b50>] (brcmf_usb_free_q+0x34/0xa8 [brcmfmac])
[ 2730.684833] [<7f258b50>] (brcmf_usb_free_q [brcmfmac]) from [<7f2517d4>] (brcmf_detach+0xa0/0xb8 [brcmfmac])
[ 2730.693557] [<7f2517d4>] (brcmf_detach [brcmfmac]) from [<7f251a34>] (brcmf_attach+0xac/0x3d8 [brcmfmac])
[ 2730.702094] [<7f251a34>] (brcmf_attach [brcmfmac]) from [<7f2587ac>] (brcmf_usb_probe_phase2+0x468/0x4a0 [brcmfmac])
[ 2730.711601] [<7f2587ac>] (brcmf_usb_probe_phase2 [brcmfmac]) from [<7f252888>] (brcmf_fw_request_done+0x194/0x220 [brcmfmac])
[ 2730.721795] [<7f252888>] (brcmf_fw_request_done [brcmfmac]) from [<805748e4>] (request_firmware_work_func+0x4c/0x88)
[ 2730.731125] [<805748e4>] (request_firmware_work_func) from [<80141474>] (process_one_work+0x228/0x808)
[ 2730.739223] [<80141474>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564)
[ 2730.746105] [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c)
[ 2730.752227] [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20)
[ 2733.099695] kworker/0:3 D 0 1065 2 0x00000000
[ 2733.103926] Workqueue: usb_hub_wq hub_event
[ 2733.106914] [<809dca20>] (__schedule) from [<809dd164>] (schedule+0x4c/0xac)
[ 2733.112693] [<809dd164>] (schedule) from [<809e2a8c>] (schedule_timeout+0x214/0x3e4)
[ 2733.119621] [<809e2a8c>] (schedule_timeout) from [<809dde2c>] (wait_for_common+0xc4/0x1c0)
[ 2733.126810] [<809dde2c>] (wait_for_common) from [<7f258d00>] (brcmf_usb_disconnect+0x1c/0x4c [brcmfmac])
[ 2733.135206] [<7f258d00>] (brcmf_usb_disconnect [brcmfmac]) from [<8069e0c8>] (usb_unbind_interface+0x5c/0x1e4)
[ 2733.143943] [<8069e0c8>] (usb_unbind_interface) from [<8056d3e8>] (device_release_driver_internal+0x164/0x1fc)
[ 2733.152769] [<8056d3e8>] (device_release_driver_internal) from [<8056c078>] (bus_remove_device+0xd0/0xfc)
[ 2733.161138] [<8056c078>] (bus_remove_device) from [<8056977c>] (device_del+0x11c/0x310)
[ 2733.167939] [<8056977c>] (device_del) from [<8069cba8>] (usb_disable_device+0xa0/0x1cc)
[ 2733.174743] [<8069cba8>] (usb_disable_device) from [<8069507c>] (usb_disconnect+0x74/0x1dc)
[ 2733.181823] [<8069507c>] (usb_disconnect) from [<80695e88>] (hub_event+0x478/0xf88)
[ 2733.188278] [<80695e88>] (hub_event) from [<80141474>] (process_one_work+0x228/0x808)
[ 2733.194905] [<80141474>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564)
[ 2733.201724] [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c)
[ 2733.207913] [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20)
It was traced down to a case where usb_kill_urb would be called on an URB
structure containing more or less random data, including large number in
its use_count. During the debugging it appeared that in brcmf_usb_free_q()
the traversal over URBs' lists is not synchronized with operations on those
lists in brcmf_usb_rx_complete() leading to handling
brcmf_usbdev_info structure (holding lists' head) as lists' element and in
result causing above problem.
Fix it by walking through all URBs during brcmf_cancel_all_urbs using the
arrays of requests instead of linked lists.
Signed-off-by: Piotr Figiel <p.figiel@camlintechnologies.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmu_pkt_buf_free_skb emits WARNING when attempting to free a sk_buff
which is part of any queue. After USB disconnect this may have happened
when brcmf_fws_hanger_cleanup() is called as per-interface psq was never
cleaned when removing the interface.
Change brcmf_fws_macdesc_cleanup() in a way that it removes the
corresponding packets from hanger table (to avoid double-free when
brcmf_fws_hanger_cleanup() is called) and add a call to clean-up the
interface specific packet queue.
Below is a WARNING during USB disconnect with Raspberry Pi WiFi dongle
running in AP mode. This was reproducible when the interface was
transmitting during the disconnect and is fixed with this commit.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1171 at drivers/net/wireless/broadcom/brcm80211/brcmutil/utils.c:49 brcmu_pkt_buf_free_skb+0x3c/0x40
Modules linked in: nf_log_ipv4 nf_log_common xt_LOG xt_limit iptable_mangle xt_connmark xt_tcpudp xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 iptable_filter ip_tables x_tables usb_f_mass_storage usb_f_rndis u_ether cdc_acm smsc95xx usbnet ci_hdrc_imx ci_hdrc ulpi usbmisc_imx 8250_exar 8250_pci 8250 8250_base libcomposite configfs udc_core
CPU: 0 PID: 1171 Comm: kworker/0:0 Not tainted 4.19.23-00075-gde33ed8 #99
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Workqueue: usb_hub_wq hub_event
[<8010ff84>] (unwind_backtrace) from [<8010bb64>] (show_stack+0x10/0x14)
[<8010bb64>] (show_stack) from [<80840278>] (dump_stack+0x88/0x9c)
[<80840278>] (dump_stack) from [<8011f5ec>] (__warn+0xfc/0x114)
[<8011f5ec>] (__warn) from [<8011f71c>] (warn_slowpath_null+0x40/0x48)
[<8011f71c>] (warn_slowpath_null) from [<805a476c>] (brcmu_pkt_buf_free_skb+0x3c/0x40)
[<805a476c>] (brcmu_pkt_buf_free_skb) from [<805bb6c4>] (brcmf_fws_cleanup+0x1e4/0x22c)
[<805bb6c4>] (brcmf_fws_cleanup) from [<805bc854>] (brcmf_fws_del_interface+0x58/0x68)
[<805bc854>] (brcmf_fws_del_interface) from [<805b66ac>] (brcmf_remove_interface+0x40/0x150)
[<805b66ac>] (brcmf_remove_interface) from [<805b6870>] (brcmf_detach+0x6c/0xb0)
[<805b6870>] (brcmf_detach) from [<805bdbb8>] (brcmf_usb_disconnect+0x30/0x4c)
[<805bdbb8>] (brcmf_usb_disconnect) from [<805e5d64>] (usb_unbind_interface+0x5c/0x1e0)
[<805e5d64>] (usb_unbind_interface) from [<804aab10>] (device_release_driver_internal+0x154/0x1ec)
[<804aab10>] (device_release_driver_internal) from [<804a97f4>] (bus_remove_device+0xcc/0xf8)
[<804a97f4>] (bus_remove_device) from [<804a6fc0>] (device_del+0x118/0x308)
[<804a6fc0>] (device_del) from [<805e488c>] (usb_disable_device+0xa0/0x1c8)
[<805e488c>] (usb_disable_device) from [<805dcf98>] (usb_disconnect+0x70/0x1d8)
[<805dcf98>] (usb_disconnect) from [<805ddd84>] (hub_event+0x464/0xf50)
[<805ddd84>] (hub_event) from [<80135a70>] (process_one_work+0x138/0x3f8)
[<80135a70>] (process_one_work) from [<80135d5c>] (worker_thread+0x2c/0x554)
[<80135d5c>] (worker_thread) from [<8013b1a0>] (kthread+0x124/0x154)
[<8013b1a0>] (kthread) from [<801010e8>] (ret_from_fork+0x14/0x2c)
Exception stack(0xecf8dfb0 to 0xecf8dff8)
dfa0: 00000000 00000000 00000000 00000000
dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
dfe0: 00000000 00000000 00000000 00000000 00000013 00000000
---[ end trace 38d234018e9e2a90 ]---
------------[ cut here ]------------
Signed-off-by: Piotr Figiel <p.figiel@camlintechnologies.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This includes bus reset & reloading a firmware. It should be sufficient
for a user space to (setup and) use a wireless device again.
Support for reset on USB & SDIO can be added later.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This improves handling PCIe firmware halts by printing a clear error
message and replaces a similar code in the SDIO bus support.
It will also allow further improvements like trying to recover from a
firmware crash.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During a normal brcmfmac lifetime brcmf_fw_alloc_request() is called
once only during the probe. It's safe to assume provided array is clear.
Further brcmfmac improvements may require calling it multiple times
though. This patch allows it by fixing invalid firmware paths like:
brcm/brcmfmac4366c-pcie.binbrcm/brcmfmac4366c-pcie.bin
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use scan duration param for both active and passive scan dwell times.
Document what different types of dwell times are used for. Explicitly
specify that if unset, automatic selection by device firmware
will be used.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use control path to send EAPOL frames to make sure they are
sent with higher priority with aggregation disabled.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch streamlines firmware state tracking. In particular, state
QTNF_FW_STATE_FW_DNLD_DONE is removed, states QTNF_FW_STATE_RESET and
QTNF_FW_STATE_DETACHED are merged into a single state. Besides, new
state QTNF_FW_STATE_RUNNING is introduced to distinguish between
the following two cases:
- firmware load succeeded, firmware init process is ongoing
- firmware init succeeded, firmware is fully functional
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Report that firmware is up and running only for successful firmware
download. Simplify qtnf_pcie_fw_boot_done: modify error path so that
no need to pass firmware dowload result to this function. Finally,
do not create debugfs entries if firmware download succeeded,
but core attach failed.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In some regions, different regulatory limits (like max Tx power) may be
defined for different operating modes. As an example: in ETSI regions
DFS master devices may use higher transmit powers compared to DFS slave
devices. Update bands information in CHANGE_INTF command if mode of
operation changes.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pass DFS region as requested by regulatory core directly to firmware
so it can initialize radar detection block accordingly.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently driver uses the same regulatory rules to register all wiphy
instances. This is not logically correct since each wiphy may have
different capabilities (different supported bands, EIRP etc).
Allow firmware to pass regulatory rules for each MAC separately.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use REGULATORY_CUSTOM_REG flag only if firmware advertised a custom
regulatory domain prior to wiphy registration. Use REGULATORY_STRICT_REG
flag only if firmware knows its regulatory domain.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently only a portion of per-channel information is passed to
firmware. Extend logic to pass all useful per-channel data.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Before regulatory notifier is invoked by a wireless core, it will
update band information for the wiphy. Pass this information to
firmware together with new region alpha2 code.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Error reporting in qtnf_cfg80211_reg_notifier only requires to print
one type of message and an error code. Firmware will report success
for an attempt to set regulatory region to the same value,
so no special handling is required for this case.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wireless core calls regulatory notifier for each wiphy and it only
guarantees that bands info is updated for this particular wiphy prior
to calling a notifier. Hence updating all wiphy which belong to driver
in a single notifier callback is redundant and incorrect.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add an error print-out in case FW and board files load fails,
as such an error is not printed on all failures and user may
not understand why the interface up operations didn't succeed.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since DR bit and buffer id are written in different dwords of
the status message, the DR bit can already be set to 1 while the
buffer id is not updated yet.
Resetting the buffer id in the status message will allow the driver
to identify such cases and re-read the status message until the buffer
id is written by HW.
In case DR bit is set but buffer id is zero, need to read the status
message again, until a valid id is identified.
In addition to that, move the completed buffer id to the tail of the
free list to prevent its immediate reuse in the upcoming refill.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver needs to expose RGF_USER_USAGE_2 register that contains
the offset of the ucode logging table.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to access control RGF_CAF_ICR cannot be accessed by host.
Such an access will cause device AHB logger to halt and it will not
capture future AHB fault if there is any.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The functions that send management TX frame have 3 possible
results: success and other side acknowledged receive (ACK=1),
success and other side did not acknowledge receive(ACK=0) and
failure to send the frame. The current implementation
incorrectly reports the ACK=0 case as failure.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Update the rx packet checksum of received packet according to edma
HW spec:
No need to calculate checksum in the following cases:
L4_status=0 and L3_status=0 - No L3 and no L4 known protocols found
L4_status=0 and L3_status=1 - L3 was found, and checksum check passed.
No known L4 protocol was found.
L4_status=1 - L4 was found, and checksum check passed.
Recalculate checksum in the following cases:
L4_status=3 and L3_status=1 - It means that L3 protocol was found,
and checksum passed, but L4 checksum failed.
L4_status=3 and L3_status=2 - Both L3 and L4 checksum check failed.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In addition to existing MAC address field in OTP, new field added for
OEM MAC address.
wil6210 gives precedence to the new OEM MAC address and will use it if
its valid.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Check that the mid is valid and that it does not exceed the memory
size allocated to vifs array.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Update max MCS to 15, which is supported by Talyn-MB.
This will allow collecting statistics on number of RX packets
in higher MCS.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
