Depending on which video standard is used the driver needs to setup the
hardware to correctly handle fields. If stream is identified as NTSC
or PAL setup field detection and propagate the field detection signal.
Later versions of the datasheet have been updated to make it clear
that FLD register should be set to 0 when dealing with non-interlaced
field formats.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Restart the CSI-2 link if the CSI-2 receiver detects an error during
reception. The driver did nothing when a link error happened and the
data flow simply stopped without the user knowing why.
Change the driver to try and recover from errors by restarting the link
and informing the user that something is not right. For obvious reasons
it's not possible to recover from all errors (video source disconnected
for example) but in such cases the user is at least informed of the
error and the same behavior of the stopped data flow is retained.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Later versions of the datasheet updates the reset procedure to more
closely resemble the standby mode. Update the driver to enter and exit
the standby mode instead of resetting the hardware before and after
streaming is started and stopped. This replaces the software reset
(SRST.SRST) control.
While at it break out the full start and stop procedures from
rcsi2_s_stream() into the existing helper functions.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The PHTW selection algorithm implemented in rcsi2_phtw_write_mbps() checks for
lower bound of the interval used to match the desired bandwidth. Use that
in place of the currently used upper bound.
Fixes: 10c08812fe ("media: rcar: rcar-csi2: Update V3M/E3 PHTW tables")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The R-Car CSI-2 interface has a number of selectable 'channels' that
provides pixel data to the VINs during image acquisition.
Each channel can be used to match a CSI-2 data type and a CSI-2 virtual
channel to be routed to output path.
Different SoCs have different number of channels, with R-Car E3 being the
notable exception supporting only 2 of them.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Initialise the V4L2 fwnode endpoints to zero in all drivers using
v4l2_fwnode_endpoint_parse(). This prepares for setting default endpoint
flags as well as the bus type. Setting bus type to zero will continue to
guess the bus among the guessable set (parallel, Bt.656 and CSI-2 D-PHY).
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Switch all media platform drivers to call v4l2_async_notifier_add_subdev()
to add asd's to a notifier, in place of referencing the notifier->subdevs[]
array. These drivers also must now call v4l2_async_notifier_init() before
adding asd's to their notifiers.
There may still be cases where a platform driver maintains a list of
asd's that is a duplicate of the notifier asd_list, in which case its
possible the platform driver list can be removed, and can reference the
notifier asd_list instead. One example of where a duplicate list has
been removed in this patch is xilinx-vipp.c. If there are such cases
remaining, those drivers should be optimized to remove the duplicate
platform driver asd lists.
None of the changes to the platform drivers in this patch have been
tested. Verify that the async subdevices needed by the platform are
bound at load time, and that the driver unloads and reloads correctly
with no memory leaking of asd objects.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
