The pm_runtime_get_noresume() calls before really_probe() and
before executing __device_attach() for each driver on the
device's bus cause problems to happen if probing fails and if the
driver has enabled runtime PM for the device in its .probe()
callback. Namely, in that case, if the device has been resumed
by the driver after enabling its runtime PM and if it turns out that
.probe() should return an error, the driver is supposed to suspend
the device and disable its runtime PM before exiting .probe().
However, because the device's runtime PM usage counter was
incremented by the core before calling .probe(), the driver's attempt
to suspend the device will not succeed and the device will remain in
the full-power state after the failing .probe() has returned.
To fix this issue, remove the pm_runtime_get_noresume() calls from
driver_probe_device() and from device_attach() and replace the
corresponding pm_runtime_put_sync() calls with pm_runtime_idle()
to preserve the existing behavior (which is to check if the device
is idle and to suspend it eventually in that case after probing).
Reported-and-tested-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When deferred probe was originally added the idea was that devices which
defer their probes would move themselves to the end of dpm_list in order
to try to keep the assumptions that we're making about the list being in
roughly the order things should be suspended correct. However this hasn't
been what's been happening and doing it requires a lot of duplicated code
to do the moves.
Instead take a simple, brute force solution and have the deferred probe
code push devices to the end of dpm_list before it retries the probe. This
does mean we lock the dpm_list a bit more often but it's very simple and
the code shouldn't be a fast path. We do the move with the deferred mutex
dropped since doing things with fewer locks held simultaneously seems like
a good idea.
This approach was most recently suggested by Grant Likely.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Grant Likely <grant.likely@secretlab.ca>,
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device driver attribute groups are created after userspace is notified
via an add event. Fix this by moving the kobject_uevent call to
driver_register after the attribute groups are added.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Firstly, .shutdown callback may touch a uninitialized hardware
if dev->driver is set and .probe is not completed.
Secondly, device_shutdown() may dereference a null pointer to cause
oops when dev->driver is cleared after it has been checked in
device_shutdown().
So just hold device lock and its parent lock(if it has) to
fix the races.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
all callers want the same thing, actually - a kinda-sorta analog of
kern_path_create(). I.e. they want parent vfsmount/dentry (with
->i_mutex held, to make sure the child dentry is still their child)
+ the child dentry.
Signed-off-by Al Viro <viro@zeniv.linux.org.uk>
The power/async device sysfs attribute is only used if both
CONFIG_PM_ADVANCED_DEBUG and CONFIG_PM_SLEEP are set, but the code
implementing it doesn't depend on CONFIG_PM_SLEEP. As a result, a
build warning appears if CONFIG_PM_ADVANCED_DEBUG is set and
CONFIG_PM_SLEEP is not set.
Fix it by adding a #ifdef CONFIG_PM_SLEEP around the code in
question.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The functions genpd_save_dev() and genpd_restore_dev() are not used
for CONFIG_PM_RUNTIME unset, so move them under an appropriate
#ifdef.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Fixes the following sparse warning:
drivers/base/power/domain.c:1679:55: warning: Using plain integer as NULL pointer
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Fixes the folloiwng sparse warning:
drivers/base/power/domain.c:149:5:
warning: symbol '__pm_genpd_poweron' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
On certain bios, resume hangs if cpus are allowed to enter idle states
during suspend [1].
This was fixed in apci idle driver [2].But intel_idle driver does not
have this fix. Thus instead of replicating the fix in both the idle
drivers, or in more platform specific idle drivers if needed, the
more general cpuidle infrastructure could handle this.
A suspend callback in cpuidle_driver could handle this fix. But
a cpuidle_driver provides only basic functionalities like platform idle
state detection capability and mechanisms to support entry and exit
into CPU idle states. All other cpuidle functions are found in the
cpuidle generic infrastructure for good reason that all cpuidle
drivers, irrepective of their platforms will support these functions.
One option therefore would be to register a suspend callback in cpuidle
which handles this fix. This could be called through a PM_SUSPEND_PREPARE
notifier. But this is too generic a notfier for a driver to handle.
Also, ideally the job of cpuidle is not to handle side effects of suspend.
It should expose the interfaces which "handle cpuidle 'during' suspend"
or any other operation, which the subsystems call during that respective
operation.
The fix demands that during suspend, no cpus should be allowed to enter
deep C-states. The interface cpuidle_uninstall_idle_handler() in cpuidle
ensures that. Not just that it also kicks all the cpus which are already
in idle out of their idle states which was being done during cpu hotplug
through a CPU_DYING_FROZEN callbacks.
Now the question arises about when during suspend should
cpuidle_uninstall_idle_handler() be called. Since we are dealing with
drivers it seems best to call this function during dpm_suspend().
Delaying the call till dpm_suspend_noirq() does no harm, as long as it is
before cpu_hotplug_begin() to avoid race conditions with cpu hotpulg
operations. In dpm_suspend_noirq(), it would be wise to place this call
before suspend_device_irqs() to avoid ugly interactions with the same.
Ananlogously, during resume.
References:
[1] https://bugs.launchpad.net/ubuntu/+source/linux/+bug/674075.
[2] http://marc.info/?l=linux-pm&m=133958534231884&w=2
Reported-and-tested-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Sometimes for failures during very early init the trace infrastructure
isn't available early enough to be used. For this sort of problem
defining LOG_DEVICE will add printks for basic register I/O on a specific
device, allowing trace to be extracted when the trace system doesn't come
up early enough to work with.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make it possible to modify device callbacks used by the generic PM
domains core code at any time, not only after the device has been
added to a domain. This will allow device drivers to provide their
own device PM domain callbacks even if they are registered before
adding the devices to PM domains.
For this purpose, use the observation that the struct
generic_pm_domain_data object containing the relevant callback
pointers may be allocated by pm_genpd_add_callbacks() and the
callbacks may be set before __pm_genpd_add_device() is run for
the given device. This object will then be used by
__pm_genpd_add_device(), but it has to be protected from
premature removal by reference counting.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add a mechanism for counting references to the
struct generic_pm_domain_data object pointed to by
dev->power.subsys_data->domain_data if the device in question
belongs to a generic PM domain.
This change is necessary for a subsequent patch making it possible to
allocate that object from within pm_genpd_add_callbacks(), so that
drivers can attach their PM domain device callbacks to devices before
those devices are added to PM domains.
This patch has been tested on the SH7372 Mackerel board.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This picks up the big printk fixes, and resolves a merge issue with:
drivers/extcon/extcon_gpio.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some systems there are CPU cores located in the same power
domains as I/O devices. Then, power can only be removed from the
domain if all I/O devices in it are not in use and the CPU core
is idle. Add preliminary support for that to the generic PM domains
framework.
First, the platform is expected to provide a cpuidle driver with one
extra state designated for use with the generic PM domains code.
This state should be initially disabled and its exit_latency value
should be set to whatever time is needed to bring up the CPU core
itself after restoring power to it, not including the domain's
power on latency. Its .enter() callback should point to a procedure
that will remove power from the domain containing the CPU core at
the end of the CPU power transition.
The remaining characteristics of the extra cpuidle state, referred to
as the "domain" cpuidle state below, (e.g. power usage, target
residency) should be populated in accordance with the properties of
the hardware.
Next, the platform should execute genpd_attach_cpuidle() on the PM
domain containing the CPU core. That will cause the generic PM
domains framework to treat that domain in a special way such that:
* When all devices in the domain have been suspended and it is about
to be turned off, the states of the devices will be saved, but
power will not be removed from the domain. Instead, the "domain"
cpuidle state will be enabled so that power can be removed from
the domain when the CPU core is idle and the state has been chosen
as the target by the cpuidle governor.
* When the first I/O device in the domain is resumed and
__pm_genpd_poweron(() is called for the first time after
power has been removed from the domain, the "domain" cpuidle
state will be disabled to avoid subsequent surprise power removals
via cpuidle.
The effective exit_latency value of the "domain" cpuidle state
depends on the time needed to bring up the CPU core itself after
restoring power to it as well as on the power on latency of the
domain containing the CPU core. Thus the "domain" cpuidle state's
exit_latency has to be recomputed every time the domain's power on
latency is updated, which may happen every time power is restored
to the domain, if the measured power on latency is greater than
the latency stored in the corresponding generic_pm_domain structure.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
While resuming a device belonging to a PM domain,
pm_genpd_runtime_resume() calls __pm_genpd_restore_device() to
restore its state, if necessary. The latter starts the device,
using genpd_start_dev(), restores its state, using
genpd_restore_dev(), and then stops it, using genpd_stop_dev().
However, this last operation is not necessary, because the
device is supposed to be operational after pm_genpd_runtime_resume()
has returned and because of it pm_genpd_runtime_resume() has to
call genpd_start_dev() once again for the "restored" device, which
is inefficient.
To make things more efficient, remove the call to genpd_stop_dev()
from __pm_genpd_restore_device() and the direct call to
genpd_start_dev() from pm_genpd_runtime_resume(). [Of course,
genpd_start_dev() still has to be called by it for devices with the
power.irq_safe flag set, because __pm_genpd_restore_device() is not
executed for them.]
This change has been tested on the SH7372 Mackerel board.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Currently, the default "save state" and "restore state" routines
for generic PM domains, pm_genpd_default_save_state() and
pm_genpd_default_restore_state(), respectively, only use runtime PM
callbacks provided by device drivers, but in general those callbacks
need not provide the entire necessary functionality. Namely, in
general it may be necessary to execute subsystem (i.e. device type,
device class or bus type) callbacks that will carry out all of the
necessary operations.
For this reason, modify pm_genpd_default_save_state() and
pm_genpd_default_restore_state() to execute subsystem callbacks,
if they are provided, and fall back to driver callbacks otherwise.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Change the behavior of the newly introduced
/sys/power/pm_print_times attribute so that its initial value
depends on initcall_debug, but setting it to 0 will cause device
suspend/resume times not to be printed, even if initcall_debug has
been set. This way, the people who use initcall_debug for reasons
other than PM debugging will be able to switch the suspend/resume
times printing off, if need be.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added a new knob called /sys/power/pm_print_times. Setting it to 1
enables printing of time taken by devices to suspend and resume.
Setting it to 0 disables this printing (unless overridden by
initcall_debug kernel command line option).
Signed-off-by: Sameer Nanda <snanda@chromium.org>
Acked-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
__device_suspend() must always send a completion. Otherwise, parent
devices will wait forever.
Commit 1e2ef05b, "PM: Limit race conditions between runtime PM and
system sleep (v2)", introduced a regression by short-circuiting the
complete_all() for certain error cases.
This patch fixes the bug by always signalling a completion.
Addresses http://crosbug.com/31972
Tested by injecting an abort.
Signed-off-by: Mandeep Singh Baines <msb@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Pull driver core and printk fixes from Greg Kroah-Hartman:
"Here are some fixes for 3.5-rc4 that resolve the kmsg problems that
people have reported showing up after the printk and kmsg changes went
into 3.5-rc1. There are also a smattering of other tiny fixes for the
extcon and hyper-v drivers that people have reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
extcon: max8997: Add missing kfree for info->edev in max8997_muic_remove()
extcon: Set platform drvdata in gpio_extcon_probe() and fix irq leak
extcon: Fix wrong index in max8997_extcon_cable[]
kmsg - kmsg_dump() fix CONFIG_PRINTK=n compilation
printk: return -EINVAL if the message len is bigger than the buf size
printk: use mutex lock to stop syslog_seq from going wild
kmsg - kmsg_dump() use iterator to receive log buffer content
vme: change maintainer e-mail address
Extcon: Don't try to create duplicate link names
driver core: fixup reversed deferred probe order
printk: Fix alignment of buf causing crash on ARM EABI
Tools: hv: verify origin of netlink connector message
Devices with register paging or indirectly accessed registers can configure
register mapping to map those on virtual address range. During access to
virtually mapped register range, indirect addressing is processed
automatically, in following steps:
1. selector for page or indirect register is updated (when needed);
2. register in data window is accessed.
Configuration should provide minimum and maximum register for virtual range,
details of selector field for page selection, minimum and maximum register of
data window for indirect access.
Virtual range registers are managed by cache as well as direct access
registers. In order to make indirect access more efficient, selector register
should be declared as non-volatile, if possible.
struct regmap_config is extended with the following:
struct regmap_range_cfg *ranges;
unsigned int n_ranges;
[Also reordered debugfs init to later on since the cleanup code was
conflicting with the new cleanup code for ranges anyway -- broonie]
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Locks are moved to regmap_update_bits(), which allows to reenter internal
function _regmap_update_bits() from inside of regmap read/write routines.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix kernel-doc warnings in drivers/base/dma*.c:
Warning(drivers/base/dma-buf.c:498): No description found for parameter 'vaddr'
Warning(drivers/base/dma-coherent.c:199): No description found for parameter 'ret'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) drvdata is for a driver to store a pointer to driver specific data
2) If no driver is bound, there is no driver specific data associated with
the device
3) Thus logically drvdata should be NULL if no driver is bound.
But many drivers don't clear drvdata on device_release, or set drvdata
early on in probe and leave it set on probe error. Both of which results
in a dangling pointer in drvdata.
This patch enforce for drvdata to be NULL after device_release or on probe
failure.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If driver requests probe deferral,
it will be added to deferred_probe_pending_list
by driver_deferred_probe_add(), but, it used list_add().
Because of that, deferred probe will be run as reversed order.
This patch uses list_add_tail(), and solved this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow chips to provide a bank of registers for controlling the wake state
in a similar fashion to the masks and propagate the wake count to the
parent interrupt controller.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the driver supplied an empty entry in the array of IRQs then return
an error rather than trying to do the mapping. This is intended for use
with handling chip variants and similar situations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The word to be transmitted/received via regmap is composed by the following
parts:
config->reg_bits
config->val_bits
config->pad_bits
,so the total size should be calculated by summing up the number of bits of
each element and using a DIV_ROUND_UP to return the number of bytes.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If debugfs isn't cleaned up, stale files will be left in the filesystem
which will cause an OOPS when accessed the first time, and hang the
accessing application when accessed again, presumably due to some lock
being left held.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will avoid the regmap core converting all addresses and values into
big endian, only for the mmio bus driver to have to convert them back to
native endian.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a field to struct regmap_bus that allows bus drivers to request that
register addresses and values be formatted with a specific endianness.
The default endianness is unchanged from current operation: Big.
Implement native endian formatting/parsing for 16- and 32-bit values.
This will be enough to support regmap-mmio.c.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull vfs changes from Al Viro.
"A lot of misc stuff. The obvious groups:
* Miklos' atomic_open series; kills the damn abuse of
->d_revalidate() by NFS, which was the major stumbling block for
all work in that area.
* ripping security_file_mmap() and dealing with deadlocks in the
area; sanitizing the neighborhood of vm_mmap()/vm_munmap() in
general.
* ->encode_fh() switched to saner API; insane fake dentry in
mm/cleancache.c gone.
* assorted annotations in fs (endianness, __user)
* parts of Artem's ->s_dirty work (jff2 and reiserfs parts)
* ->update_time() work from Josef.
* other bits and pieces all over the place.
Normally it would've been in two or three pull requests, but
signal.git stuff had eaten a lot of time during this cycle ;-/"
Fix up trivial conflicts in Documentation/filesystems/vfs.txt (the
'truncate_range' inode method was removed by the VM changes, the VFS
update adds an 'update_time()' method), and in fs/btrfs/ulist.[ch] (due
to sparse fix added twice, with other changes nearby).
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (95 commits)
nfs: don't open in ->d_revalidate
vfs: retry last component if opening stale dentry
vfs: nameidata_to_filp(): don't throw away file on error
vfs: nameidata_to_filp(): inline __dentry_open()
vfs: do_dentry_open(): don't put filp
vfs: split __dentry_open()
vfs: do_last() common post lookup
vfs: do_last(): add audit_inode before open
vfs: do_last(): only return EISDIR for O_CREAT
vfs: do_last(): check LOOKUP_DIRECTORY
vfs: do_last(): make ENOENT exit RCU safe
vfs: make follow_link check RCU safe
vfs: do_last(): use inode variable
vfs: do_last(): inline walk_component()
vfs: do_last(): make exit RCU safe
vfs: split do_lookup()
Btrfs: move over to use ->update_time
fs: introduce inode operation ->update_time
reiserfs: get rid of resierfs_sync_super
reiserfs: mark the superblock as dirty a bit later
...
Since there are uses for I2C_M_NOSTART which are much more sensible and
standard than most of the protocol mangling functionality (the main one
being gather writes to devices where something like a register address
needs to be inserted before a block of data) create a new I2C_FUNC_NOSTART
for this feature and update all the users to use it.
Also strengthen the disrecommendation of the protocol mangling while we're
at it.
In the case of regmap-i2c we remove the requirement for mangling as
I2C_M_NOSTART is the only mangling feature which is being used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
/sys/devices/system/node/{online,possible} outputs a garbage byte
because print_nodes_state() returns content size + 1. To fix the bug,
the patch changes the use of cpuset_sprintf_cpulist to follow the use at
other places, which is clearer and safer.
This bug was introduced in v2.6.24 (commit bde631a518: "mm: add node
states sysfs class attributeS").
Signed-off-by: Ryota Ozaki <ozaki.ryota@gmail.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull dma-buf updates from Sumit Semwal:
"Here's the first signed-tag pull request for dma-buf framework. It
includes the following key items:
- mmap support
- vmap support
- related documentation updates
These are needed by various drivers to allow mmap/vmap of dma-buf
shared buffers. Dave Airlie has some prime patches dependent on the
vmap pull as well."
* tag 'tag-for-linus-3.5' of git://git.linaro.org/people/sumitsemwal/linux-dma-buf:
dma-buf: add initial vmap documentation
dma-buf: minor documentation fixes.
dma-buf: add vmap interface
dma-buf: mmap support
Pull CMA and ARM DMA-mapping updates from Marek Szyprowski:
"These patches contain two major updates for DMA mapping subsystem
(mainly for ARM architecture). First one is Contiguous Memory
Allocator (CMA) which makes it possible for device drivers to allocate
big contiguous chunks of memory after the system has booted.
The main difference from the similar frameworks is the fact that CMA
allows to transparently reuse the memory region reserved for the big
chunk allocation as a system memory, so no memory is wasted when no
big chunk is allocated. Once the alloc request is issued, the
framework migrates system pages to create space for the required big
chunk of physically contiguous memory.
For more information one can refer to nice LWN articles:
- 'A reworked contiguous memory allocator':
http://lwn.net/Articles/447405/
- 'CMA and ARM':
http://lwn.net/Articles/450286/
- 'A deep dive into CMA':
http://lwn.net/Articles/486301/
- and the following thread with the patches and links to all previous
versions:
https://lkml.org/lkml/2012/4/3/204
The main client for this new framework is ARM DMA-mapping subsystem.
The second part provides a complete redesign in ARM DMA-mapping
subsystem. The core implementation has been changed to use common
struct dma_map_ops based infrastructure with the recent updates for
new dma attributes merged in v3.4-rc2. This allows to use more than
one implementation of dma-mapping calls and change/select them on the
struct device basis. The first client of this new infractructure is
dmabounce implementation which has been completely cut out of the
core, common code.
The last patch of this redesign update introduces a new, experimental
implementation of dma-mapping calls on top of generic IOMMU framework.
This lets ARM sub-platform to transparently use IOMMU for DMA-mapping
calls if one provides required IOMMU hardware.
For more information please refer to the following thread:
http://www.spinics.net/lists/arm-kernel/msg175729.html
The last patch merges changes from both updates and provides a
resolution for the conflicts which cannot be avoided when patches have
been applied on the same files (mainly arch/arm/mm/dma-mapping.c)."
Acked by Andrew Morton <akpm@linux-foundation.org>:
"Yup, this one please. It's had much work, plenty of review and I
think even Russell is happy with it."
* 'for-linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping: (28 commits)
ARM: dma-mapping: use PMD size for section unmap
cma: fix migration mode
ARM: integrate CMA with DMA-mapping subsystem
X86: integrate CMA with DMA-mapping subsystem
drivers: add Contiguous Memory Allocator
mm: trigger page reclaim in alloc_contig_range() to stabilise watermarks
mm: extract reclaim code from __alloc_pages_direct_reclaim()
mm: Serialize access to min_free_kbytes
mm: page_isolation: MIGRATE_CMA isolation functions added
mm: mmzone: MIGRATE_CMA migration type added
mm: page_alloc: change fallbacks array handling
mm: page_alloc: introduce alloc_contig_range()
mm: compaction: export some of the functions
mm: compaction: introduce isolate_freepages_range()
mm: compaction: introduce map_pages()
mm: compaction: introduce isolate_migratepages_range()
mm: page_alloc: remove trailing whitespace
ARM: dma-mapping: add support for IOMMU mapper
ARM: dma-mapping: use alloc, mmap, free from dma_ops
ARM: dma-mapping: remove redundant code and do the cleanup
...
Conflicts:
arch/x86/include/asm/dma-mapping.h
Some minor inline documentation fixes for gaps resulting from new patches.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
The main requirement I have for this interface is for scanning out
using the USB gpu devices. Since these devices have to read the
framebuffer on updates and linearly compress it, using kmaps
is a major overhead for every update.
v2: fix warn issues pointed out by Sylwester Nawrocki.
v3: fix compile !CONFIG_DMA_SHARED_BUFFER and add _GPL for now
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Compared to Rob Clark's RFC I've ditched the prepare/finish hooks
and corresponding ioctls on the dma_buf file. The major reason for
that is that many people seem to be under the impression that this is
also for synchronization with outstanding asynchronous processsing.
I'm pretty massively opposed to this because:
- It boils down reinventing a new rather general-purpose userspace
synchronization interface. If we look at things like futexes, this
is hard to get right.
- Furthermore a lot of kernel code has to interact with this
synchronization primitive. This smells a look like the dri1 hw_lock,
a horror show I prefer not to reinvent.
- Even more fun is that multiple different subsystems would interact
here, so we have plenty of opportunities to create funny deadlock
scenarios.
I think synchronization is a wholesale different problem from data
sharing and should be tackled as an orthogonal problem.
Now we could demand that prepare/finish may only ensure cache
coherency (as Rob intended), but that runs up into the next problem:
We not only need mmap support to facilitate sw-only processing nodes
in a pipeline (without jumping through hoops by importing the dma_buf
into some sw-access only importer), which allows for a nicer
ION->dma-buf upgrade path for existing Android userspace. We also need
mmap support for existing importing subsystems to support existing
userspace libraries. And a loot of these subsystems are expected to
export coherent userspace mappings.
So prepare/finish can only ever be optional and the exporter /needs/
to support coherent mappings. Given that mmap access is always
somewhat fallback-y in nature I've decided to drop this optimization,
instead of just making it optional. If we demonstrate a clear need for
this, supported by benchmark results, we can always add it in again
later as an optional extension.
Other differences compared to Rob's RFC is the above mentioned support
for mapping a dma-buf through facilities provided by the importer.
Which results in mmap support no longer being optional.
Note that this dma-buf mmap patch does _not_ support every possible
insanity an existing subsystem could pull of with mmap: Because it
does not allow to intercept pagefaults and shoot down ptes importing
subsystems can't add some magic of their own at these points (e.g. to
automatically synchronize with outstanding rendering or set up some
special resources). I've done a cursory read through a few mmap
implementions of various subsytems and I'm hopeful that we can avoid
this (and the complexity it'd bring with it).
Additonally I've extended the documentation a bit to explain the hows
and whys of this mmap extension.
In case we ever want to add support for explicitly cache maneged
userspace mmap with a prepare/finish ioctl pair, we could specify that
userspace needs to mmap a different part of the dma_buf, e.g. the
range starting at dma_buf->size up to dma_buf->size*2. This works
because the size of a dma_buf is invariant over it's lifetime. The
exporter would obviously need to fall back to coherent mappings for
both ranges if a legacy clients maps the coherent range and the
architecture cannot suppor conflicting caching policies. Also, this
would obviously be optional and userspace needs to be able to fall
back to coherent mappings.
v2:
- Spelling fixes from Rob Clark.
- Compile fix for !DMA_BUF from Rob Clark.
- Extend commit message to explain how explicitly cache managed mmap
support could be added later.
- Extend the documentation with implementations notes for exporters
that need to manually fake coherency.
v3:
- dma_buf pointer initialization goof-up noticed by Rebecca Schultz
Zavin.
Cc: Rob Clark <rob.clark@linaro.org>
Cc: Rebecca Schultz Zavin <rebecca@android.com>
Acked-by: Rob Clark <rob.clark@linaro.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Pull power management updates from Rafael Wysocki:
- Implementation of opportunistic suspend (autosleep) and user space
interface for manipulating wakeup sources.
- Hibernate updates from Bojan Smojver and Minho Ban.
- Updates of the runtime PM core and generic PM domains framework
related to PM QoS.
- Assorted fixes.
* tag 'pm-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (25 commits)
epoll: Fix user space breakage related to EPOLLWAKEUP
PM / Domains: Make it possible to add devices to inactive domains
PM / Hibernate: Use get_gendisk to verify partition if resume_file is integer format
PM / Domains: Fix computation of maximum domain off time
PM / Domains: Fix link checking when add subdomain
PM / Sleep: User space wakeup sources garbage collector Kconfig option
PM / Sleep: Make the limit of user space wakeup sources configurable
PM / Documentation: suspend-and-cpuhotplug.txt: Fix typo
PM / Domains: Cache device stop and domain power off governor results, v3
PM / Domains: Make device removal more straightforward
PM / Sleep: Fix a mistake in a conditional in autosleep_store()
epoll: Add a flag, EPOLLWAKEUP, to prevent suspend while epoll events are ready
PM / QoS: Create device constraints objects on notifier registration
PM / Runtime: Remove device fields related to suspend time, v2
PM / Domains: Rework default domain power off governor function, v2
PM / Domains: Rework default device stop governor function, v2
PM / Sleep: Add user space interface for manipulating wakeup sources, v3
PM / Sleep: Add "prevent autosleep time" statistics to wakeup sources
PM / Sleep: Implement opportunistic sleep, v2
PM / Sleep: Add wakeup_source_activate and wakeup_source_deactivate tracepoints
...
Pull a regmap kconfig dependency fix from Mark Brown:
"Fix the dependency on IRQ_DOMAIN for REGMAP_IRQ in the core
Fixes a missing select from the Palmas driver a bit more throoughly."
* tag 'regmap-domain-deps' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Use select .. if to get IRQ_DOMAIN enabled
