Conflicts:
arch/arm/mach-omap1/gpio16xx.c
drivers/gpio/gpio-omap.c
Merge in the runtime-pm-cleanup branch from the gpio tree into
next/cleanup, this resolves a nonobvious merge conflict between
the two branches. Both branches move parts of the gpio-omap
driver into platform code, this takes the superset of both
changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The main purpose of this patch is to fix several section mismatch
warnings from the board file and a few board specific drivers,
introduced with recent Amstrad Delta patch series, some of them rising
up only when building with CONFIG_MODULES not set.
While being at it, section tagging of all init data found in the board
file have been revised and hopefully corrected and/or optimized.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While resolving section mismatches introduced with recent patches
to for-next, a few dangerous, driver bind/unbind unaware section
tagging already present in mainline have been identified. Fix them.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'omap1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
input: serio: ams-delta: toggle keyboard power over GPIO
omapfb: lcd_ams_delta: drive control lines over GPIO
MTD: NAND: ams-delta: use GPIO instead of custom I/O
LED: drop leds-ams-delta driver
ARM: OMAP1: ams-delta: supersede custom led device by leds-gpio
ARM: OMAP1: ams-delta: convert latches to basic_mmio_gpio
ARM: OMAP1: ams-delta: register latch dependent devices later
This is needed to minimize io.h so the SoC specific io.h
for ARMs can removed.
Note that minimal driver changes for DSS and RNG are needed to
include cpu.h for SoC detection macros.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's no need to have these in plat/io.h.
While at it, clean up the includes to group them
like they typically are grouped.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we can remove omap_read/write call from the GPIO driver
and remove include to linux/io.h.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some OMAP1 board files define LCD platform_devices, but there are no
corresponding LCD drivers for those in the kernel. Thus remove these LCD
devices.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
LCD config for old omapfb driver is passed with OMAP_TAG_LCD from board
files or from the bootloader. In an effort to remove OMAP_TAG_LCD, this
patch adds omapfb_set_lcd_config() function that the board files can
call to set the LCD config.
This has the drawback that configuration can no longer come from the
bootloader. Of the boards supported by the kernel, this should only
affect N770 which depends on the data from the bootloader. This patch
adds an LCD config for N770 to its board files, but that is most
probably broken. Fixing this would need information about the HW setup
in N770 boards.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
In an effort to clean up the old omapfb driver, this patch removes
HWA742 (the display chip used in N770) platform data. This can be done
as N770 is the only user of HWA742, and the platform data contains only
one field, te_connected, which we can just presume to be true in the
HWA742 driver.
This allows us to remove omapfb_set_ctrl_platform_data(), and the
mechanism to pass the platform data, in a later patch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Otherwise we can get the following on some compilers:
arch/arm/mach-omap1/board-innovator.c:419:19: warning:
array subscript is above array bounds [-Warray-bounds]
arch/arm/mach-omap1/board-innovator.c:425:19: warning:
array subscript is above array bounds [-Warray-bounds]
Signed-off-by: Tony Lindgren <tony@atomide.com>
In all OMAP1 SoCs, the MPUIO bank width is 16 bits. But, in OMAP7xx,
it is wrongly initialised to 32. Fix this.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The only bank->type (method) used in the OMAP GPIO driver is MPUIO type as they
need to be handled separately. Identify the same using a flag and remove all
METHOD_* macros.
mpuio_init() function is defined under #ifdefs. It is required only in case
of MPUIO bank type and only when PM operations are supported by it.
This is applicable only in case of OMAP16xx SoC's MPUIO GPIO bank type.
For all the other cases it is a dummy function. Hence clean up the same
and remove all the OMAP SoC specific #ifdefs.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
With register offsets now defined for respective OMAP versions we can get rid
of cpu_class_* checks. This function now has common initialization code for
all OMAP versions. Initialization specific to OMAP16xx has been moved within
omap16xx_gpio_init().
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Getting rid of ifdefs within the function by adding register offset intctrl
and associating OMAPXXXX_GPIO_INT_CONTROL in respective SoC specific files.
Also, use wkup_status register consistently instead of referring to wakeup
clear and wakeup set register offsets. Get rid of cpu_is_xxxx checks in
set_gpio_trigger() using irqctrl.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Wakeup enable register offset initialized according to OMAP versions
during device registration. Use this to avoid version checks.
Starting with OMAP4, legacy registers should not be used in combination
with the updated regsiters. Use wkup_en register consistently for
all SoCs wherever applicable.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The gpio_bank_count is the count of number of GPIO devices in a SoC. Remove this
dependency from the driver by using list. Also remove the dependency on array of
pointers to gpio_bank struct of all GPIO devices.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Commit 9ccdac3662 ([ARM] idle:
clean up pm_idle calling, obey hlt_counter) removed a check
for NULL pm_idle.
Replace the NULL assignment in the OMAP1 code with disable_hlt()
to be in sync with the core code and restore the intended behavior.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
New feature development
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
* tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mfd/db8500-prcmu: remove support for early silicon revisions
ARM: ux500: fix the smp_twd clock calculation
ARM: ux500: remove support for early silicon revisions
ARM: ux500: update register files
ARM: ux500: register DB5500 PMU dynamically
ARM: ux500: update ASIC detection for U5500
ARM: ux500: support DB8520
ARM: picoxcell: implement watchdog restart
ARM: OMAP3+: hwmod data: Add the default clockactivity for I2C
ARM: OMAP3: hwmod data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3
ARM: OMAP: hwmod data: Add support for AM35xx UART4/ttyO3
ARM: Orion: Remove address map info from all platform data structures
ARM: Orion: Get address map from plat-orion instead of via platform_data
ARM: Orion: mbus_dram_info consolidation
ARM: Orion: Consolidate the address map setup
ARM: Kirkwood: Add configuration for MPP12 as GPIO
ARM: Kirkwood: Recognize A1 revision of 6282 chip
ARM: ux500: update the MOP500 GPIO assignments
...
Hook these platforms restart code into the new restart hook rather
than using arch_reset().
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Don't use Amstrad Delta custom I/O functions once GPIO interface is
available for the underlying hardware.
While requesting and initializing GPIO pins used, also take care of one
extra pin KEYBRD_DATAOUT which, even if not used by the driver, belongs
to the device and affects its functioning.
Once done, move the driver initialization back to the device_initcall
level, reverting the temporary chane introduced with patch 1/7 "ARM:
OMAP1: ams-delta: register latch dependent devices later". That change
is no longer required once the driver takes care of registering used
GPIO pins, and it's better to initialize the device before others using
the latch2 based GPIO pins, otherwise a garbage is reported on boot,
perhaps due to random data already captured by the FIQ handler while the
keyboard related latch bits are written with random values during
initialization of those other latch2 dependent devices.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
[tony@atomide.com: renamed _gpios to ams_delta_gpios]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Don't use Amstrad Delta custom I/O functions any longer, use GPIO API
instead.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Don't use Amstrad Delta custom I/O functions for controlling the device,
use GPIO API instead.
While being at it, add missing gpio_free(AMS_DELTA_GPIO_PIN_NAND_RB).
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Cc: David Woodhouse <dwmw2@infradead.org>
Reviewed-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that the Amstrad Delta on-board latches have been converted to GPIO
devices, use the generic driver to control on-board LEDs which hang off
those latches.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Once ready, ams-delta specific device drivers currently calling custom
ams_delta_latch[12]_write() functions can be updated to call generic
gpio_set_value() instead, which will make them less platform dependent.
Even more, some custom ams-delta only drivers can perhaps be dropped
from the tree after converting selected ams-delta platform devices to
follow generic GPIO based device models.
The latch_gpios[] table is initially filled with all latch1 and latch2
GPIO pins in order to register and initialize them from the board file
until those are handled by respective existing device drivers (leds,
nand, lcd, serio, asoc, serial). That table will get almost empty after
the transision process is completed, holding only pins not used by any
drivers / connected to unused devices, in order to initialize them from
the board file for power saving purposes.
The new ams_delta_latch_write() function is a unified replacement for
those removed ams_delta_latch[12]_write(), and serves as a temporary
wrapper over gpio_set_value(), providing the old API for those not yet
updated device drivers, and will be removed after all custom drivers are
converted or replaced.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In preparation to converting Amstrad Delta on-board latches to
basic_mmio_gpio devices, registration of platform devices which depend
on latches and will require initialization of their GPIO pins first,
should be moved out of .machine_init down to late_initcall level, as the
gpio-generic driver is not available until device_initcall time. The
latch reset operation, which will be replaced with GPIO initialization,
must also be moved to late_initcall for the same reason.
Since there was already another, separate arch_initcall function for
setting up one of those latch dependent devices, the on-board modem
device, reuse that function, i.e., rename it to a name that matches the
new purpose, extend with other device setup relocated from
.machine_init, and move down to the late_initcall level.
While being at it, add missing gpio_free() in case the modem platform
device registration fails.
Thanks to Tony Lindgren <tony@atomide.com> who suggested this approach
instead of shifting up the gpio-generic driver initialization.
In addition, defer registration of the Amstrad Delta ASoC and serio
devices, done from their device driver files, until late_initcall time,
as those drivers will depend on their GPIO pins already requested from
the board late_init() function until updated to register their GPIO pins
themselves.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DPLL1 reprogramming to a different rate is actually blocked inside
omap1_select_table_rate(). However, it is already forced at boot, for
boards which boot at unusable clock rates, and this seems to work
correctly.
OTOH, we now have a fine, run time performed clock selection algorithm
implemented, which prevents less powerfull SoCs from being overclocked
unintentionally.
Allow reprogramming of dpll1 by default, and use it for switching to the
higest supported clock rate with all boards, including those already
booting at a usable rate of 60 MHz or above.
Created against linux-omap/master tip as of Thu Dec 1,
commit f83c2a8cbb59981722d1ab610c79adfd034a2667. Requires the just
submitted patch "ARM: OMAP1: Move dpll1 rates selection from config to
runtime" to prevent from unintentional overclocking. Tested on Amstrad
Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to comments in omap1_select_table_rate(), reprogramming dpll1
is tricky, and should always be done from SRAM.
While being at it, move OMAP730 special case handling inside
omap_sram_reprogram_clock().
Created on top of version 2 of the series "ARM: OMAP1: Fix dpll1
reprogramming related issues", which it depends on.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For still better multi-OMAP1 support, expand omap1_rate_table with flags
for different SoC types and match them while selecting clock rates. The
idea is stolen from current omap24xx clock rate selection algorithm.
Since clkdev platform flag definitions are reused here, those had to be
expanded with one extra entry for OMAP1710 subtype, as this is the only
SoC for which we allow selection of the highest, 216 MHz rate.
Once done, remove no longer needed clock rate configure time options.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise timing is inaccurate, resulting in devices which depend on it,
like omap-keypad, broken.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: removed comment referencing a development branch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the exact value found in omap1_rate_table, otherwise I have been
experiencing issues with correct timekeeping on my Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: removed comment referencing a development branch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit e9b7086b80 (ARM: OMAP: Fix
reprogramming of dpll1 rate) fixed a regression for systems that
did not rely on bootloader set rates.
However, it also introduced a new problem where the rates selected
in .config would not take affect as omap1_select_table_rate
currently refuses to reprogram DPLL1 if it's already initialized.
This was not a problem earlier, as the reprogramming was done
earlier with ck_dpll1_p->rate uninitialized.
Fix this by forcing the reprogramming on systems booting at rates
below 60MHz. Note that the long term fix is to make the rates
SoC specific later on.
Thanks for Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for figuring
this one out.
Reported-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A generic version should replace this later.
As io.c has become nearly empty, omap_init_consistent_dma_size() is moved
into common.c so that io.c can be removed entirely.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Kevin Hilman <khilman@ti.com>
