This patch enables the vop0 and hdmi nodes
for a MK808 with rk3066 processor.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds the GPIO line names from the schematics to get them displayed
in the debugfs output of each GPIO controller.
The schematics from Odroid-C1+ PCB revision 0.4 20150615 are used as
referenced.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
When entering suspend-to-mem, all PMIC outputs are disabled except
VDDIODDR which is put in power saving mode, and whose voltage is
increased (probably to counter the poor accuracy of power saving mode).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
[claudiu.beznea@microchip.com: use regulator-changeable-in-suspend,
regulator-suspend-max-microvolt, regulator-suspend-max-microvolt,
use macros for regulators' states, add regulator-inital-state]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Mighty is basically the same Chromebook as Jaq but it has a full-sized
SD slot and some different (slightly more rugged) plastics around it.
Like Jaq, Mighty may show up with various different brandings but all
of them have the same board inside.
In the downstream kernel Mighty and Jaq share a "dtsi" and Mighty just
adds the SD write protect (needed for a full-sized SD slot). We'll do
this upstream by just including the Jaq dts and make the changes.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Describe the remaining 3 LEDs, which are driven by the first CAT9554
port expander.
Drop the superfluous status property from the leds node while at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the I2C bus, and add the following devices:
- Two CAT9554 port expanders (8 GPIOs, interrupt not wired by
default),
- R1EX24016ASAS0A EEPROM.
The bus also contains a MAX9856 Audio Codec, which is not yet supported.
All devices (incl. the audio codec) are documented to support an I2C bus
running at 400 kHz.
Pinctrl is based on the RZ/A BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The recently added uart mux options had a few typos. Fix them.
Fixes: 43d0fe112585 ("ARM: dts: sun7i: add pinctrl for missing uart mux options")
Reported-by: Werner Böllmann <Werner.Boellmann@fh-dortmund.de>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
We switched to the generic pinctrl binding some time ago, yet the GMAC
pinctrl node apparently slipped through. Fix this.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The USB OTG binding we have mandates to have a dr_mode property, yet not
all boards are setting it.
Since the generic otg binding states that the default mode should be the
OTG mode, let's use that one in our DTSI.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
We must not use legacy clock defines for dts clckctrl clocks as the offsets
will be wrong.
Fixes: 87fc89ced3 ("ARM: dts: am335x: Move l4 child devices to probe them with ti-sysc")
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add i.MX7ULP OCOTP support, its clock source is from
M4 BUS clock which is NOT available in Linux clock tree,
but M4 BUS clock is always ON when A7 (Linux) is alive,
so just use dummy clock here.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is one of two boards that make use of the recently introduced SIOX
bus. Apart from the devices described in the dts it features a display
with touch that I didn't include here because it needs some non-mainline
change to operate correctly.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support of stm32mp157c discovery2 board (part number: STM32MP157C-DK2).
This board is a "super-set" of stm32mp157a-dk1. It embeds a STM32MP157c SOC
with AC package (TFBGA361, 148 ios) and 512MB of DDR3. Same connections
than stm32mp157a-dk1 board are available. Display panel (otm8009a) and
Murata wifi/BT combo is added.
This patch adds basic support for a kernel boot and enable otm8009a display
panel.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support of stm32mp157a discovery1 board (part number: STM32MP157A-DK1).
This board embeds a STM32MP157a SOC with AC package (TFBGA361, 148 ios)
and 512MB of DDR3. Several connections are available on this boards:
4*USB2.0, 1*USB2.0 typeC, SDcard, RJ45, HDMI, Arduino connector, ...
This patch enables basic support for a kernel boot.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The USB OTG binding we have mandates to have a dr_mode property, yet not
all boards are setting it.
Since the generic otg binding states that the default mode should be the
OTG mode, let's use that one in our DTSI.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The NAND pinctrl nodes names don't follow the pattern we've used and
enforced for some time. Make sure they do.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The children nodes of the pinctrl node hadn't have any reg property for
quite some time, so we don't need the size-cells property. Remove it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The SATA controller never have any children nodes, so we don't need the
address and size cells properties.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The AHCI node was introduced with a typo in the reset-names property that
got written resets-name instead.
This was working because the reset is optional for that driver, and the
controller was put out of reset by the bootloader.
Fixes: 41c64d3318 ("ARM: dts: sun8i: r40: add sata node")
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Even though it doesn't make any difference at the binary level, the reg
property is an array of cells, and should be represented as such.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The regulator properties suffix is -supply, yet a _supply slipped in.
This was working because the regulator framework will provide a dummy
regulator when none is provided in the device tree, and the regulator
itself was always enabled.
Fixes: 90c5d7cdae ("ARM: dts: sun8i: a711: Add regulator support")
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Even though we shouldn't really have any external user of the clock
provided by the TCON, if clock-output-names is set, then #clock-cells must
be there as well.
Fix this.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
While the USB PHY Device Tree mandates that the name of the VBUS detect pin
should be usb0_vbus_det-gpios, a significant number of device tree use
usb0_vbus_det-gpio instead.
This was functional because the GPIO framework falls back to the gpio
suffix that is legacy, but we should fix this.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
While the USB PHY Device Tree mandates that the name of the ID detect pin
should be usb0_id_det-gpios, a significant number of device tree use
usb0_id_det-gpio instead.
This was functional because the GPIO framework falls back to the gpio
suffix that is legacy, but we should fix this.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The i2c-gpio driver uses named gpios now and the array of GPIOs is
deprecated. Switch to the new binding.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
As can be shown by the YAML schema now, the combination of GIC compatibles
we were using has never been an option.
Switch to the gic-400 variant, which is the more correct option.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Some nodes still have pinctrl-names entry, yet they don't have any pinctrl
group anymore. Drop them.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Commit 1848f3f444 ("ARM: dts: sun9i: Remove GPIO pinctrl nodes to avoid
warnings") was wrong on the optimus, and instead of droping the
pinctrl-names property, it dropped the regulator-name one.
Obviously, that wasn't what was intended. Reinstate regulator-name and drop
pinctrl-names.
Fixes: 1848f3f444 ("ARM: dts: sun9i: Remove GPIO pinctrl nodes to avoid warnings")
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A23 and A33 both have an I2C controller in the ARISC domain, that share
the same pins with the RSB bus.
Even if it's an unusual configuration, that device can be used to drive the
PMIC, so let's use it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The DSI bindings require that an address cell size of 1, and a size cell of
0. Instead of duplicating it in each and every board DTS file, let's put it
in the DTSI.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The soc node in the A80 DTSI has a ranges property, but no matching unit
address, which results in a DTC warning. Add the unit address to remove
that warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Our display engine endpoints trigger some DTC warnings due to the fact that
we're having a single endpoint that doesn't need any reg property, and
since we don't have a reg property, we don't need the address-cells and
size-cells properties anymore.
Fix those
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Our display engine endpoints trigger some DTC warnings due to the fact that
we're having a single endpoint that doesn't need any reg property, and
since we don't have a reg property, we don't need the address-cells and
size-cells properties anymore.
Fix those
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Our display engine endpoints trigger some DTC warnings due to the fact that
we're having a single endpoint that doesn't need any reg property, and
since we don't have a reg property, we don't need the address-cells and
size-cells properties anymore.
Fix those
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Our display engine endpoints trigger some DTC warnings due to the fact that
we're having a single endpoint that doesn't need any reg property, and
since we don't have a reg property, we don't need the address-cells and
size-cells properties anymore.
Fix those
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Our display engine endpoints trigger some DTC warnings due to the fact that
we're having a single endpoint that doesn't need any reg property, and
since we don't have a reg property, we don't need the address-cells and
size-cells properties anymore.
Fix those
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Our display engine endpoints trigger some DTC warnings due to the fact that
we're having a single endpoint that doesn't need any reg property, and
since we don't have a reg property, we don't need the address-cells and
size-cells properties anymore.
Fix those
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Our display engine endpoints trigger some DTC warnings due to the fact that
we're having a single endpoint that doesn't need any reg property, and
since we don't have a reg property, we don't need the address-cells and
size-cells properties anymore.
Fix those
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Since most of the display IPs have a single endpoint, having a reg
property, a unit-address and #address-cells and #size-cells will emit a
warning.
Let's remove those.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Unlike what the binding for multiple pipeline documents, the A83t doesn't
have the cross links between the TCON and the mixers.
Let's add them.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Make sure that A20 Olimex Lime2 pin bank regulators are
properly represented.
While pin banks A, B and F are connected to 3.3V static
regulator, pin banks E and G tied with LDO3 and LDO4 regulators
with 2.8V reference.
Signed-off-by: Priit Laes <priit.laes@paf.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Since only one alternative at a time is used, and some functions may not
be used at all, this cuts down the size of the board dtb files a bit.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds pinctrl settings the EMAC using pins in the PH block.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds pinctrl settings for the CAN controller using pins
PA16 and PA17.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds pinctrl settings for various missing uart options.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
