The example node in the binding uses the AST2500 compatible string for
the SD controller with a 64kiB ranges property, but the SD controller is
allocated 128kiB of MMIO space according to the AST2500 datasheet. Fix
the example to correctly reflect the hardware in the AST2500, however it
should be noted that the MMIO region is reduced to 64kiB in the AST2600
where a second SD controller block has been introduced into the address
space.
Also add the IBM copyright header that I left out of the initial patch.
Suggested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ASPEED SD/SDIO/MMC controller exposes two slots implementing the
SDIO Host Specification v2.00, with 1 or 4 bit data buses, or an 8 bit
data bus if only a single slot is enabled.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a new compatible for the additional emmc2 controller
on BCM2711 and clearify usage.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC compatibles in the bindings are not ordered as they should, so
let's make sure it's sorted.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ast2600 is a new generation of SoC from ASPEED. Similarly to the
ast2400 and ast2500, it has a GPIO controller for it's 3.3V GPIO pins.
Additionally, it has a GPIO controller for 36 1.8V GPIO pins. We use
the ngpio property to differentiate between these controllers.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Link: https://lore.kernel.org/r/20190906062547.13264-1-rashmica.g@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the documentation to the compatible regulator-fixed-clock.
This binding is a special binding of regulator-fixed and adds the
ability to add a clock to regulator-fixed, so the regulator can be
enabled and disabled with that clock. If the special compatible
regulator-fixed-clock is used it is mandatory to supply a clock.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20190910062103.39641-4-philippe.schenker@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add optional bindings "vpcie3v3-supply" and "vpcie12v-supply" to describe
regulators of a PCIe slot's supplies 3.3V and 12V provided the platform
is designed to have regulator controlled slot supplies.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Pull irqchip updates for Linux 5.4 from Marc Zyngier:
- Large GICv3 updates to support new PPI and SPI ranges
- Conver all alloc_fwnode() users to use PAs instead of VAs
- Add support for Marvell's MMP3 irqchip
- Add support for Amlogic Meson SM1
- Various cleanups and fixes
The g12a audio subsystem, which is a derivative of the axg subsystem,
provides a dedicated reset line for each of the audio components.
The axg did not provide that and it is unclear if/when these reset are
required. The reset already helped solve a channel mapping issue on the
tdm formatter devices. Let's add the reset binding for the other
components, so we can describe this in DT. We'll use it later on
in the driver when/if needed.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20190905120120.31752-3-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Removal of the rk3288-fennec board which never made it to
any market.
* tag 'v5.4-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
dt-bindings: arm: rockchip: remove reference to fennec board
ARM: dts: rockchip: remove rk3288 fennec board support
Link: https://lore.kernel.org/r/1718334.9BoTfW0Ujv@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add devicetree bindings for Rockchip cru which found on
Rockchip SoCs.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Peter writes:
Add role switch class support for chipidea
* tag 'usb-ci-v5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: chipidea: msm: Use device-managed registration API
usb: chipidea: add role switch class support
dt-binding: usb: usbmisc-imx: add imx7ulp compatible
dt-binding: usb: ci-hdrc-usb2: add imx7ulp compatible
Tegra186 chip has a hardware issue resulting in frame errors when
tolerance level for baud rate is negative. Provided entries to adjust
baud rate to be within acceptable range and work with devices that
can send negative baud rate. Also report error when baud rate set is
out of tolerance range of controller updated in device tree.
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-10-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marc Kleine-Budde says:
====================
pull-request: can-next 2019-09-03
this is a pull request for net-next/master consisting of 15 patches.
The first patch is by Christer Beskow, targets the kvaser_pciefd driver
and fixes the PWM generator's frequency.
The next three patches are by Dan Murphy, the tcan4x5x is updated to use
a proper interrupts/interrupt-parent DT binding to specify the devices
IRQ line. Further the unneeded wake ups of the device is removed from
the driver.
A patch by me for the mcp25xx driver removes the deprecated board file
setup example. Three patches by Andy Shevchenko simplify clock handling,
update the driver from OF to device property API and simplify the
mcp251x_can_suspend() function.
The remaining 7 patches are by me and clean up checkpatch warnings in
the generic CAN device infrastructure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ARM cpufreq driver changes for 5.4 from Viresh Kumar:
"This contains:
- Minor fixes for mediatek driver (Andrew-sh.Cheng and Fabien Parent).
- Minor updates for imx driver (Anson Huang).
- Minor fix for ti-cpufreq driver (Gustavo A. R. Silva).
- Minor fix for ap806 driver (Hariprasad Kelam).
- Significant updates to qcom cpufreq drivers, mostly to support CPR
stuff (Jorge Ramirez-Ortiz, Niklas Cassel, Sibi Sankar, Douglas
RAILLARD and Sricharan R).
- New sun50i cpufreq driver (Yangtao Li).
It also contains a few OPP changes which were required because of
dependencies for the qcom cpufreq changes."
* 'cpufreq/arm/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm: (22 commits)
cpufreq: Add qcs404 to cpufreq-dt-platdev blacklist
cpufreq: qcom: Add support for qcs404 on nvmem driver
cpufreq: qcom: Refactor the driver to make it easier to extend
cpufreq: qcom: Re-organise kryo cpufreq to use it for other nvmem based qcom socs
dt-bindings: opp: Add qcom-opp bindings with properties needed for CPR
dt-bindings: opp: qcom-nvmem: Support pstates provided by a power domain
cpufreq: mediatek: Add support for mt8183
cpufreq: mediatek: change to regulator_get_optional
cpufreq: imx-cpufreq-dt: Add i.MX8MN support
cpufreq: Use imx-cpufreq-dt for i.MX8MN's speed grading
cpufreq: qcom-hw: invoke frequency-invariance setter function
cpufreq: qcom-hw: Update logic to detect turbo frequency
cpufreq: mediatek-cpufreq: Add compatible for MT8516
cpufreq: ti-cpufreq: Mark expected switch fall-through
dt-bindings: opp: qcom-nvmem: Make speedbin related properties optional
dt-bindings: opp: Re-organise kryo cpufreq to use it for other nvmem based qcom socs
opp: Add dev_pm_opp_find_level_exact()
opp: Return genpd virtual devices from dev_pm_opp_attach_genpd()
opp: Not all power-domains are scalable
cpufreq: ap806: Add NULL check after kcalloc
...
Pull operating performance points (OPP) framework changes for 5.4
from Viresh Kumar:
"This contains:
- OPP core fixes to better support genpd devices (Viresh Kumar).
- OPP core changes to support multiple suspend-opps in DT (Anson Huang).
- New OPP API (dev_pm_opp_find_level_exact()) and Qcom OPP binding
changes for CPR (Niklas Cassel).
- Qcom minor update (Sricharan R).
- OPP Documentation fix (Yue Hu).
- OPP core support to enable/disable regulators (k.konieczny)."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
dt-bindings: opp: Add qcom-opp bindings with properties needed for CPR
dt-bindings: opp: qcom-nvmem: Support pstates provided by a power domain
dt-bindings: opp: qcom-nvmem: Make speedbin related properties optional
dt-bindings: opp: Re-organise kryo cpufreq to use it for other nvmem based qcom socs
PM / OPP: Correct Documentation about library location
opp: of: Support multiple suspend OPPs defined in DT
dt-bindings: opp: Support multiple opp-suspend properties
opp: core: add regulators enable and disable
opp: Don't decrement uninitialized list_kref
opp: Add dev_pm_opp_find_level_exact()
opp: Return genpd virtual devices from dev_pm_opp_attach_genpd()
opp: Not all power-domains are scalable
The timeriomem_rng driver only accesses the first 4 bytes of the given
memory area and currently, it also forces that memory resource to be
exactly 4 bytes in size.
This, however, is problematic when used with device-trees that are
generated from things like FPGA toolchains, where the minimum size
of an exposed memory block may be something like 4k.
Hence, let's only check for what's needed for the driver to operate
properly; namely that we have enough memory available to read the
random data from.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
TISCI protocol supports for enabling the device either with exclusive
permissions for the requesting host or with sharing across the hosts.
There are certain devices which are exclusive to Linux context and
there are certain devices that are shared across different host contexts.
So add support for getting this information from DT by increasing
the power-domain cells to 2.
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mvebu dt64 for 5.4 (part 2)
Add support for Turris Mox board (Armada 3720 SoC based)
* tag 'mvebu-dt64-5.4-2' of git://git.infradead.org/linux-mvebu: (53 commits)
arm64: dts: marvell: add DTS for Turris Mox
dt-bindings: marvell: document Turris Mox compatible
arm64: dts: marvell: armada-37xx: add SPI CS1 pinctrl
arm64: dts: marvell: Add cpu clock node on Armada 7K/8K
arm64: dts: marvell: Convert 7k/8k usb-phy properties to phy-supply
arm64: dts: marvell: Add 7k/8k PHYs in PCIe nodes
arm64: dts: marvell: Add 7k/8k PHYs in USB3 nodes
arm64: dts: marvell: Add 7k/8k per-port PHYs in SATA nodes
arm64: dts: marvell: Add CP110 COMPHY clocks
arm64: dts: marvell: armada-37xx: add mailbox node
dt-bindings: gpio: Document GPIOs via Moxtet bus
drivers: gpio: Add support for GPIOs over Moxtet bus
bus: moxtet: Add sysfs and debugfs documentation
dt-bindings: bus: Document moxtet bus binding
bus: Add support for Moxtet bus
reset: Add support for resets provided by SCMI
firmware: arm_scmi: Add RESET protocol in SCMI v2.0
dt-bindings: arm: Extend SCMI to support new reset protocol
firmware: arm_scmi: Make use SCMI v2.0 fastchannel for performance protocol
firmware: arm_scmi: Add discovery of SCMI v2.0 performance fastchannels
...
Link: https://lore.kernel.org/r/87h85two0r.fsf@FE-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Texas Instruments K3 SoC family changes for 5.4
- Typo fixes for gic-its unit addresses for both am654 and j721e
- HW spinlock nodes added for both am654 and j721e
- GPIO support for j721e
- power-domain cells update for both am654 / j721e for exclusive only
access
* tag 'ti-k3-soc-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux:
arm64: dts: ti: k3-j721e-main: Fix gic-its node unit-address
arm64: dts: ti: k3-am65-main: Fix gic-its node unit-address
arm64: dts: ti: k3-j721e-main: Add hwspinlock node
arm64: dts: ti: k3-am65-main: Add hwspinlock node
arm64: dts: k3-j721e: Add gpio-keys on common processor board
dt-bindings: pinctrl: k3: Introduce pinmux definitions for J721E
arm64: dts: ti: k3-j721e-common-proc-board: Disable unused gpio modules
arm64: dts: ti: k3-j721e: Add gpio nodes in wakeup domain
arm64: dts: ti: k3-j721e: Add gpio nodes in main domain
arm64: dts: ti: k3-j721e: Update the power domain cells
arm64: dts: ti: k3-am654: Update the power domain cells
soc: ti: ti_sci_pm_domains: Add support for exclusive and shared access
dt-bindings: ti_sci_pm_domains: Add support for exclusive and shared access
firmware: ti_sci: Allow for device shared and exclusive requests
Link: https://lore.kernel.org/r/b838d666-ab3b-7d41-67d4-09d606c732da@ti.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
