The XUSB pad controller allows PCIe lanes to be controlled individually,
providing fine-grained control over their power state. Previous attempts
at describing the XUSB pad controller in DT had erroneously assumed that
all PCIe lanes were driven by the same PHY, and hence the PCI host
controller would reference only a single PHY.
Moving to a representation of per-lane PHYs requires that the operating
system driver for the PCI host controller have access to the set of PHY
devices that make up the connection of each root port in order to power
up and down all of the lanes as necessary.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit adds the Device Tree binding documentation that allows to
describe the PCIe controller found in Marvell Armada 7K/8K SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Rob Herring <rob@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Freescale has stated [1] that the LVDS clock source of the IMX6 does not
pass the PCI Gen2 clock jitter test, therefore unless an external Gen2
compliant external clock source is present and supplied back to the IMX6
PCIe core via LVDS CLK1/CLK2 you can not claim Gen2 compliance.
Add a DT property to specify Gen1 vs Gen2 and check this before allowing a
Gen2 link.
We default to Gen1 if the property is not present because at this time
there are no IMX6 boards in mainline that 'input' a clock on LVDS
CLK1/CLK2.
In order to be Gen2 compliant on IMX6 you need to:
- Have a Gen2 compliant external clock generator and route that clock back
to either LVDS CLK1 or LVDS CLK2 as an input (see IMX6SX-SabreSD
reference design).
- Specify this clock in the PCIe node in the DT (i.e.,
IMX6QDL_CLK_LVDS1_IN or IMX6QDL_CLK_LVDS2_IN instead of
IMX6QDL_CLK_LVDS1_GATE which configures it as a CLK output).
[1] https://community.freescale.com/message/453209
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Zhu Richard <Richard.Zhu@freescale.com>
CC: Akshay Bhat <akshay.bhat@timesys.com>
CC: Rob Herring <robh+dt@kernel.org>
CC: Shawn Guo <shawnguo@kernel.org>
Currently the reset-gpio DT property which controls the PCI bus device
reset signal defaults to active-low reset sequence (L=reset state,
H=operation state) plus the code in reset function isn't GPIO polarity
aware - it doesn't matter if the defined reset-gpio is active-low or
active-high, it will always result into active-low reset sequence.
I've tried to fix it properly and change the reset-gpio reset sequence to
be polarity-aware, but this patch has been accepted and then reverted as it
has introduced few backward incompatible issues:
1. Some DTBs, for example, imx6qdl-sabresd, don't define reset-gpio
polarity correctly:
reset-gpio = <&gpio7 12 0>;
which means that it's defined as active-high, but in reality it's
active-low; thus it wouldn't work without a DTS fix.
2. The logic in the reset function is inverted:
gpio_set_value_cansleep(imx6_pcie->reset_gpio, 0)
msleep(100);
gpio_set_value_cansleep(imx6_pcie->reset_gpio, 1);
so even if some of the i.MX6 boards had reset-gpio polarity defined
correctly in their DTSes, they would stop working.
As we can't break old DTBs, we can't fix them, so we need to introduce this
new DT reset-gpio-active-high boolean property so we can support boards
with active-high reset sequence.
This active-high reset sequence is for example needed on Apalis SoMs, where
GPIO1_IO28, used to PCIe reset is not connected directly to PERST# PCIe
signal, but it's ORed with RESETBMCU coming off the PMIC, and thus is
inverted, active-high.
Tested-by: Tim Harvey <tharvey@gateworks.com> # Gateworks Ventana boards (which have active-low PERST#)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Add initial PCIe support for the imx6 SoC derivate imx6sx. PCI MSI support
is untested as the necessary suspend/resume quirk is not included in this
patch.
This patch is heavily based on patches by Richard Zhu.
[bhelgaas: factor out refclk enable, fix adjacent typos in imx6q-pcie.txt]
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Acked-by: Richard Zhu <Richard.Zhu@freescale.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Keystone PCI hardware generates error interrupts at RC using a platform IRQ
instead of a standard MSI or legacy IRQ. Add a simple error handler that
logs the fatal interrupt status to the console.
[bhelgaas: s/node/dev->of_node/, tidy comments, return irqreturn_t directly]
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Kumar Gala <galak@codeaurora.org>
Pull ARM DT updates from Arnd Bergmann:
"These are all the updates to device tree files for 32-bit platforms,
plus a couple of related 64-bit updates:
New SoC support:
- Allwinner A83T
- Axis Artpec-6 SoC
- Mediatek MT7623 SoC
- TI Keystone K2G SoC
- ST Microelectronics stm32f469
New board or machine support:
- ARM Juno R2
- Buffalo Linkstation LS-QVL and LS-GL
- Cubietruck plus
- D-Link DIR-885L
- DT support for ARM RealView PB1176 and PB11MPCore
- Google Nexus 7
- Homlet v2
- Itead Ibox
- Lamobo R1
- LG Optimus Black
- Logicpd dm3730
- Raspberry Pi Model A
Other changes include
- Lots of updates for Qualcomm APQ8064, MSM8974 and others
- Improved support for Nokia N900 and other OMAP machines
- Common clk support for lpc32xx
- HDLCD display on ARM
- Improved stm32f429 support
- Improved Renesas device support, r8a779x and others
- Lots of Rockchip updates
- Samsung cleanups
- ADC support for Atmel SAMA5D2
- BCM2835 (Raspberry Pi) improvements
- Broadcom Northstar Plus enhancements
- OMAP GPMC rework
- Several improvements for Atmel SAMA5D2 / Xplained
- Global change to remove inofficial "arm,amba-bus" compatible
string"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (350 commits)
ARM, ARM64: dts: drop "arm,amba-bus" in favor of "simple-bus"
ARM: dts: artpec: dual-license on artpec6.dtsi
ARM: dts: ux500: add synaptics RMI4 for Ux500 TVK DT
arm64: dts: juno/vexpress: fix node name unit-address presence warnings
arm64: dts: foundation-v8: add SBSA Generic Watchdog device node
ARM: dts: at91: sama5d2 Xplained: add leds node
ARM: dts: at91: sama5d2 Xplained: add user push button
ARM: dts: at91: sama5d2 Xplained: set pin muxing for usb gadget and usb host
ARM: dts: stm32f429: Enable Ethernet on Eval board
ARM: dts: omap3-sniper: TWL4030 keypad support
Revert "ARM: dts: DRA7: Add dt nodes for PWMSS"
ARM: dts: dm814x: dra62x: Disable wait pin monitoring for NAND
ARM: dts: dm814x: dra62x: Fix NAND device nodes
ARM: dts: stm32f429: Add Ethernet support
ARM: dts: stm32f429: Add system config bank node
ARM: dts: at91: sama5d2: add nand0 and nfc0 nodes
ARM: dts: at91: sama5d2: add dma properties to UART nodes
ARM: dts: at91: sama5d2 Xplained: Correct the macb irq pinctrl node
ARM: dts: exynos: Don't overheat the Odroid XU3-Lite on high load
ARM: dts: exynos: Add cooling levels for Exynos5422/5800 CPUs
...
* pci/host-designware:
PCI: designware: Add driver for prototyping kits based on ARC SDP
PCI: designware: Add default link up check if sub-driver doesn't override
PCI: designware: Add generic dw_pcie_wait_for_link()
ARC: Add PCI support
The cavium,pci-thunder-ecam devices are exactly ECAM-based PCI root
complexes. These root complexes (loosely referred to as ECAM units in the
hardware manuals) are used to access the Thunder on-chip devices. They
are special in that all the BARs on devices behind these root complexes are
at fixed addresses.
Add a driver for these devices that synthesizes Enhanced Allocation (EA)
capability entries for each BAR.
Since this EA synthesis is needed for exactly two chip models, we can hard-
code some assumptions about the device topology and the layout of the
config space of specific DEVFNs in the driver.
[bhelgaas: changelog, whitespace]
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
The root complexes used to access off-chip PCIe devices (called PEM units
in the hardware manuals) on some Cavium ThunderX processors require quirky
access methods for the config space of the PCIe bridge.
Add a driver to provide these config space accessor functions. Use the
pci-host-common code to configure the PCI machinery.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The settings in GPR8 are dependent upon the particular layout of the
hardware platform. As such, they should be configurable via the device
tree.
Look up PHY Tx driver settings from the device tree. Fall back to the
original hard-coded values if they are not specified in the device tree.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
The patch adds LS2085a to PCIe compatible to fix the compatibility
issue when using firmware with LS2085a compatible property.
Signed-off-by: Minghuan Lian <minghuan.lian@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add "renesas,pcie-r8a7793" as a compatibility string for
"renesas,pcie-rcar-gen2".
This doesn't change the driver, so it does nothing by itself. But it
does mean that checkpatch won't complain about a future patch that adds
"renesas,pci-r8a7793" to a DT, which helps ensure that shipped DTs use
documented compatibility strings.
[bhelgaas: changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Add "renesas,pci-r8a7793" as a compatibility string for
"renesas,pci-rcar-gen2".
This doesn't change the driver, so it does nothing by itself. But it
does mean that checkpatch won't complain about a future patch that adds
"renesas,pci-r8a7793" to a DT, which helps ensure that shipped DTs use
documented compatibility strings.
[bhelgaas: changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Add support for the HiSilicon Hip06 SoC. Documentation has been updated to
include Hip06. Add Gabriele Paoloni as maintainer of the driver.
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Add fallback compatibility string for R-Car Gen 2 family. This is in
keeping with the fallback scheme being adopted wherever appropriate for
drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add fallback compatibility string for R-Car Gen 2 family. This is in
keeping with the fallback scheme being adopted wherever appropriate for
drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Add a new compatible string "brcm,iproc-pcie-paxc", for PAXC-based iProc
PCIe root complex. A PAXC-based PCIe root complex is connected to emulated
endpoint devices internal to the ASIC.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Pull ARM DT updates from Olof Johansson:
"As usual, this is the massive branch we have for each release. Lots
of various updates and additions of hardware descriptions on existing
hardware, as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and
32-bit DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to
tell from the diffstat, so there's little point in duplicating listing
it here)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (499 commits)
ARM: dts: uniphier: add system-bus-controller nodes
ARM64: juno: disable NOR flash node by default
ARM: dts: uniphier: add outer cache controller nodes
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
ARM: dts: uniphier: add I2C aliases for ProXstream2 boards
dts/Makefile: Add build support for LS2080a QDS & RDB board DTS
dts/ls2080a: Add DTS support for LS2080a QDS & RDB boards
dts/ls2080a: Update Simulator DTS to add support of various peripherals
dts/ls2080a: Remove text about writing to Free Software Foundation
dts/ls2080a: Update DTSI to add support of various peripherals
doc: DTS: Update DWC3 binding to provide reference to generic bindings
doc/bindings: Update GPIO devicetree binding documentation for LS2080A
Documentation/dts: Move FSL board-specific bindings out of /powerpc
Documentation: DT: Add entry for FSL LS2080A QDS and RDB boards
arm64: Rename FSL LS2085A SoC support code to LS2080A
arm64: Use generic Layerscape SoC family naming
ARM: dts: uniphier: add ProXstream2 Vodka board support
ARM: dts: uniphier: add ProXstream2 Gentil board support
...
Pull DeviceTree updates from Rob Herring:
"A fairly large (by DT standards) pull request this time with the
majority being some overdue moving DT binding docs around to
consolidate similar bindings.
- DT binding doc consolidation moving similar bindings to common
locations. The majority of these are display related which were
scattered in video/, fb/, drm/, gpu/, and panel/ directories.
- Add new config option, CONFIG_OF_ALL_DTBS, to enable building all
dtbs in the tree for most arches with dts files (except powerpc for
now).
- OF_IRQ=n fixes for user enabled CONFIG_OF.
- of_node_put ref counting fixes from Julia Lawall.
- Common DT binding for wakeup-source and deprecation of all similar
bindings.
- DT binding for PXA LCD controller.
- Allow ignoring failed PCI resource translations in order to ignore
64-bit addresses on non-LPAE 32-bit kernels.
- Support setting the NUMA node from DT instead of only from parent
device.
- Couple of earlycon DT parsing fixes for address and options"
* tag 'devicetree-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (45 commits)
MAINTAINERS: update DT binding doc locations
devicetree: add Sigma Designs vendor prefix
of: simplify arch_find_n_match_cpu_physical_id() function
Documentation: arm: Fixed typo in socfpga fpga mgr example
Documentation: devicetree: fix reference to legacy wakeup properties
Documentation: devicetree: standardize/consolidate on "wakeup-source" property
drivers: of: removing assignment of 0 to static variable
xtensa: enable building of all dtbs
mips: enable building of all dtbs
metag: enable building of all dtbs
metag: use common make variables for dtb builds
h8300: enable building of all dtbs
arm64: enable building of all dtbs
arm: enable building of all dtbs
arc: enable building of all dtbs
arc: use common make variables for dtb builds
of: add config option to enable building of all dtbs
of/fdt: fix error checking for earlycon address
of/overlay: add missing of_node_put
of/platform: add missing of_node_put
...
* pci/host-altera:
PCI: altera: Add Altera PCIe MSI driver
PCI: altera: Add Altera PCIe host controller driver
ARM: Add msi.h to Kbuild
* pci/host-designware:
PCI: designware: Make "clocks" and "clock-names" optional DT properties
PCI: designware: Make driver arch-agnostic
ARM/PCI: Replace pci_sys_data->align_resource with global function pointer
PCI: designware: Use of_pci_get_host_bridge_resources() to parse DT
Revert "PCI: designware: Program ATU with untranslated address"
PCI: designware: Move calculation of bus addresses to DRA7xx
PCI: designware: Make "num-lanes" an optional DT property
PCI: designware: Require config accesses to be naturally aligned
PCI: designware: Simplify dw_pcie_cfg_read/write() interfaces
PCI: designware: Use exact access size in dw_pcie_cfg_read()
PCI: spear: Fix dw_pcie_cfg_read/write() usage
PCI: designware: Set up high part of MSI target address
PCI: designware: Make get_msi_addr() return phys_addr_t, not u32
PCI: designware: Implement multivector MSI IRQ setup
PCI: designware: Factor out MSI msg setup
PCI: Add msi_controller setup_irqs() method for special multivector setup
PCI: designware: Fix PORT_LOGIC_LINK_WIDTH_MASK
* pci/host-generic:
PCI: generic: Fix address window calculation for non-zero starting bus
PCI: generic: Pass starting bus number to pci_scan_root_bus()
PCI: generic: Allow multiple hosts with different map_bus() methods
arm64: dts: Drop linux,pci-probe-only from the Seattle DTS
powerpc/PCI: Fix lookup of linux,pci-probe-only property
PCI: generic: Fix lookup of linux,pci-probe-only property
of/pci: Add of_pci_check_probe_only to parse "linux,pci-probe-only"
* pci/host-imx6:
PCI: imx6: Add PCIE_PHY_RX_ASIC_OUT_VALID definition
PCI: imx6: Return real error code from imx6_add_pcie_port()
* pci/host-iproc:
PCI: iproc: Fix header comment "Corporation" misspelling
PCI: iproc: Add outbound mapping support
PCI: iproc: Update PCIe device tree bindings
PCI: iproc: Improve link detection logic
PCI: iproc: Fix PCIe reset logic
PCI: iproc: Call pci_fixup_irqs() for ARM64 as well as ARM
PCI: iproc: Remove unused struct iproc_pcie.irqs[]
PCI: iproc: Fix code comment to match code
* pci/host-mvebu:
PCI: mvebu: Remove code restricting accesses to slot 0
PCI: mvebu: Add PCI Express root complex capability block
PCI: mvebu: Improve clock/reset handling
PCI: mvebu: Use gpio_desc to carry around gpio
PCI: mvebu: Use devm_kcalloc() to allocate an array
PCI: mvebu: Use gpio_set_value_cansleep()
PCI: mvebu: Split port parsing and resource claiming from port setup
PCI: mvebu: Fix memory leaks and refcount leaks
PCI: mvebu: Move port parsing and resource claiming to separate function
PCI: mvebu: Use port->name rather than "PCIe%d.%d"
PCI: mvebu: Report full node name when reporting a DT error
PCI: mvebu: Use for_each_available_child_of_node() to walk child nodes
PCI: mvebu: Use of_get_available_child_count()
PCI: mvebu: Use exact config access size; don't read/modify/write
PCI: mvebu: Return zero for reserved or unimplemented config space
* pci/host-rcar:
PCI: rcar: Fix I/O offset for multiple host bridges
PCI: rcar: Set root bus nr to that provided in DT
PCI: rcar: Remove dependency on ARM-specific struct hw_pci
PCI: rcar: Make PCI aware of the I/O resources
PCI: rcar: Build pcie-rcar.c only on ARM
PCI: rcar: Build pci-rcar-gen2.c only on ARM
* pci/host-tegra:
PCI: tegra: Wrap static pgprot_t initializer with __pgprot()
* pci/host-xgene:
PCI/MSI: xgene: Remove msi_controller assignment
Add Altera PCIe MSI driver. This soft IP supports a configurable number of
vectors, which is a DTS parameter.
[bhelgaas: Kconfig depend on PCIE_ALTERA, typos, whitespace]
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Both LS1043a and LS2080a are based on ARMv8 64-bit architecture and have
similar PCIe implementation. LUT is added to controller.
Add LS1043a and LS2080a support.
[bhelgaas: move unused field removal into separate patch, include DT update]
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com> (DT update)
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de> (DT update)
Move the clock-related properties in the DesignWare PCIe controller
bindings to 'optional' set of properties.
[bhelgaas: move to separate patch]
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Currently "num-lanes" is read in dw_pcie_host_init(), but it is only used
if we call dw_pcie_setup_rc() while bringing up the link. If the link has
already been brought up by firmware, we need not call dw_pcie_setup_rc(),
and "num-lanes" is unnecessary.
Only complain about "num-lanes" if we actually need it and we didn't find a
valid value.
[bhelgaas: changelog]
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ARM's Juno R1 board used PLDA XpressRICH3-AXI IP to implement a PCIe host
bridge. Introduce "plda" as vendor prefix for PLDA and document the DT
bindings for PLDA XpressRICH3-AXI IP as well as ARM's Juno R1.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Add the Altera PCIe host controller driver.
[bhelgaas: whitespace, fold in DT and maintainer updates, OF_PCI
dependency from Arnd]
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Rob Herring <robh@kernel.org> (DT binding)
Update broken links to PCI bus and interrupt mapping bindings.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Currently msi-parent is used by a few bindings to describe the
relationship between a PCI root complex and a single MSI controller, but
this property does not have a generic binding document.
Additionally, msi-parent is insufficient to describe more complex
relationships between MSI controllers and devices under a root complex,
where devices may be able to target multiple MSI controllers, or where
MSI controllers use (non-probeable) sideband information to distinguish
devices.
This patch adds a generic binding for mapping PCI devices to MSI
controllers. This document covers msi-parent, and a new msi-map property
(specific to PCI*) which may be used to map devices (identified by their
Requester ID) to sideband data for each MSI controller that they may
target.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Make the offset from the beginning of the "reg" property be from the
starting bus number, rather than zero. Hoist the invariant size
calculation out of the mapping for loop.
Update host-generic-pci.txt to clarify the semantics of the "reg" property
with respect to non-zero starting bus numbers.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Update the device tree bindings with added support for outbound mapping
configurations.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PERST# line in am57x-evm is connected to a GPIO line and PERST# should
be driven high to indicate the clocks are stable (As per Figure 2-10: Power
Up of the PCIe CEM spec 3.0).
Add support to make GPIO drive PERST# line.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
