Pull ARM SoC driver updates from Arnd Bergmann:
"This contains driver changes that are tightly connected to SoC
specific code. Aside from smaller cleanups and bug fixes, here is a
list of the notable changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver for its
on-board pluggable extension bus. The same platform also gains a
firmware driver.
- The Samsung Exynos family gains a new Chipid driver exporting using
the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon chips.
- A firmware driver for the NXP i.MX DSP IPC protocol using shared
memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for the S905X3 and A311D
chips
- A rework of the TI Davinci framebuffer driver to allow important
cleanups in the platform code
- A couple of device drivers for removed ARM SoC platforms are
removed. Most of the removals were picked up by other maintainers,
this contains whatever was left"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
bus: uniphier-system-bus: use devm_platform_ioremap_resource()
soc: ti: ti_sci_pm_domains: Add support for exclusive and shared access
dt-bindings: ti_sci_pm_domains: Add support for exclusive and shared access
firmware: ti_sci: Allow for device shared and exclusive requests
bus: imx-weim: remove incorrect __init annotations
fbdev: remove w90x900/nuc900 platform drivers
spi: remove w90x900 driver
net: remove w90p910-ether driver
net: remove ks8695 driver
firmware: turris-mox-rwtm: Add sysfs documentation
firmware: Add Turris Mox rWTM firmware driver
dt-bindings: firmware: Document cznic,turris-mox-rwtm binding
bus: moxtet: fix unsigned comparison to less than zero
bus: moxtet: remove set but not used variable 'dummy'
ARM: scoop: Use the right include
dt-bindings: power: add Amlogic Everything-Else power domains bindings
soc: amlogic: Add support for Everything-Else power domains controller
fbdev: da8xx: use resource management for dma
fbdev: da8xx-fb: drop a redundant if
fbdev: da8xx-fb: use devm_platform_ioremap_resource()
...
Qualcomm ARM Based Driver Updates for v5.4
* Add AOSS QMP support
* Various fixups for Qualcomm SCM
* Add socinfo driver
* Add SoC serial number attribute and associated APIs
* Add SM8150 and SC7180 support in Qualcomm SCM
* Fixup max processor count in SMEM
* tag 'qcom-drivers-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: aoss: Add AOSS QMP support
dt-bindings: soc: qcom: aoss: Add SM8150 and SC7180 support
dt-bindings: firmware: scm: Add SM8150 and SC7180 support
dt-bindings: firmware: scm: re-order compatible list
soc: qcom: smem: Update max processor count
soc: qcom: socinfo: Annotate switch cases with fall through
soc: qcom: Extend AOSS QMP driver to support resources that are used to wake up the SoC.
soc: qcom: socinfo: Expose image information
soc: qcom: socinfo: Expose custom attributes
soc: qcom: Add socinfo driver
base: soc: Export soc_device_register/unregister APIs
base: soc: Add serial_number attribute to soc
firmware: qcom_scm: Cleanup code in qcom_scm_assign_mem()
firmware: qcom_scm: Fix some typos in docs and printks
firmware: qcom_scm: Use proper types for dma mappings
This adds DT bindings for the Intel IXP4xx Network Processing
Engine (NPE). These are three firmware-executing units found in
the IXP4xx SoC. These bindings use YAML.
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This property is not used by device trees and was likely supposed to be
a hint as to what the BPMP node should be named, rather than describing
a property of the BPMP node.
Suggested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The BPMP is a specific processor in Tegra210 chip, which is designed
for boot process handling, assisting in entering deep low power states
(suspend to ram), and offloading DRAM memory clock scaling on some
platforms.
Signed-off-by: Timo Alho <talho@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
arm64: zynqmp: SoC CLK changes for v4.20
This patchset adds CCF compliant clock driver for ZynqMP.
Clock driver queries supported clock information from firmware
and regiters pll and output clocks with CCF.
* tag 'zynqmp-soc-clk-for-v4.20' of https://github.com/Xilinx/linux-xlnx:
drivers: clk: Add ZynqMP clock driver
dt-bindings: clock: Add bindings for ZynqMP clock driver
firmware: xilinx: Add zynqmp IOCTL API for device control
Documentation: xilinx: Add documentation for eemi APIs
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm ARM Based Driver Updates for v4.20
* Refactor of SCM compatibles and clock requirements
* SMEM cleanup
* Add LLCC EDAC driver
* Fixes for GENI clocks and macros
* Fix includes for llcc-slice and smem
* String overflow fixes for APR and wcnss_ctrl
* Fixup for COMPILE_TEST of qcom driver Kconfigs
* Cleanup of Kconfig depends of rpmh, smd_rpm, smsm, and smp2p
* Add SCM dependencies to SPM and rmtfs-mem
* tag 'qcom-drivers-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux: (38 commits)
soc: qcom: geni: geni_se_clk_freq_match() should always accept multiples
soc: qcom: geni: Don't ignore clk_round_rate() errors in geni_se_clk_tbl_get()
soc: qcom: geni: Make version macros simpler
dt-bindings: firmware: scm: Add MSM8998 and SDM845
firmware: qcom: scm: Refactor clock handling
dt-bindings: firmware: scm: Refactor compatibles and clocks
soc: qcom: smem: a few last cleanups
soc: qcom: smem: verify partition host ids match
soc: qcom: smem: small change in global entry loop
soc: qcom: smem: verify partition offset_free_uncached
soc: qcom: smem: verify partition header size
soc: qcom: smem: introduce qcom_smem_partition_header()
soc: qcom: smem: require order of host ids to match
soc: qcom: smem: verify both host ids in partition header
soc: qcom: smem: small refactor in qcom_smem_enumerate_partitions()
soc: qcom: smem: always ignore partitions with 0 offset or size
soc: qcom: smem: initialize region struct only when successful
soc: qcom: smem: rename variable in qcom_smem_get_global()
drivers: qcom: rpmh-rsc: clear wait_for_compl after use
soc: qcom: rmtfs-mem: Validate that scm is available
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add documentation to describe Xilinx ZynqMP firmware driver
bindings. Firmware driver provides an interface to firmware
APIs. Interface APIs can be used by any driver to communicate
to PMUFW (Platform Management Unit).
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Now that the compatible/clock handling is reworked add compatibles for
MSM8998 and SDM845 to the SCM binding.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
When the binding was written all "future" platforms required three
clocks, so the default compatible (qcom,scm) was defined to require
this. But as history shows all "future" platforms actually lack required
clocks. Given how the binding is written these compatibles have to be
added as an exception to the default.
Refactor the description of compatible to define that a platform
compatible should be given, followed by the fallback of qcom,scm. Also
refactor the description of the clocks in a way that this does not need
to be updated as new platform specific compatibles are added.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Pull ARM SoC driver updates from Arnd Bergmann:
"This branch contains platform-related driver updates for ARM and
ARM64, these are the areas that bring the changes:
New drivers:
- driver support for Renesas R-Car V3M (R8A77970)
- power management support for Amlogic GX
- a new driver for the Tegra BPMP thermal sensor
- a new bus driver for Technologic Systems NBUS
Changes for subsystems that prefer to merge through arm-soc:
- the usual updates for reset controller drivers from Philipp Zabel,
with five added drivers for SoCs in the arc, meson, socfpa,
uniphier and mediatek families
- updates to the ARM SCPI and PSCI frameworks, from Sudeep Holla,
Heiner Kallweit and Lorenzo Pieralisi
Changes specific to some ARM-based SoC
- the Freescale/NXP DPAA QBMan drivers from PowerPC can now work on
ARM as well
- several changes for power management on Broadcom SoCs
- various improvements on Qualcomm, Broadcom, Amlogic, Atmel,
Mediatek
- minor Cleanups for Samsung, TI OMAP SoCs"
[ NOTE! This doesn't work without the previous ARM SoC device-tree pull,
because the R8A77970 driver is missing a header file that came from
that pull.
The fact that this got merged afterwards only fixes it at this point,
and bisection of that driver will fail if/when you walk into the
history of that driver. - Linus ]
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (96 commits)
soc: amlogic: meson-gx-pwrc-vpu: fix power-off when powered by bootloader
bus: add driver for the Technologic Systems NBUS
memory: omap-gpmc: Remove deprecated gpmc_update_nand_reg()
soc: qcom: remove unused label
soc: amlogic: gx pm domain: add PM and OF dependencies
drivers/firmware: psci_checker: Add missing destroy_timer_on_stack()
dt-bindings: power: add amlogic meson power domain bindings
soc: amlogic: add Meson GX VPU Domains driver
soc: qcom: Remote filesystem memory driver
dt-binding: soc: qcom: Add binding for rmtfs memory
of: reserved_mem: Accessor for acquiring reserved_mem
of/platform: Generalize /reserved-memory handling
soc: mediatek: pwrap: fix fatal compiler error
soc: mediatek: pwrap: fix compiler errors
arm64: mediatek: cleanup message for platform selection
soc: Allow test-building of MediaTek drivers
soc: mediatek: place Kconfig for all SoC drivers under menu
soc: mediatek: pwrap: add support for MT7622 SoC
soc: mediatek: pwrap: add common way for setup CS timing extenstion
soc: mediatek: pwrap: add MediaTek MT6380 as one slave of pwrap
..
Improve the binding example by removing all the leading zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find ./Documentation/devicetree/bindings "*.txt"`
Some unnecessary changes were manually fixed.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
In order to aid post-mortem debugging the Qualcomm platforms provide a
"memory download mode", where the boot loader will provide an interface
for custom tools to "download" the content of RAM to a host machine.
The mode is triggered by writing a magic value somewhere in RAM, that is
read in the boot code path after a warm-restart. Two mechanism for
setting this magic value are supported in modern platforms; a direct SCM
call to enable the mode or through a secure io write of a magic value.
In order for a normal reboot not to trigger "download mode" the magic
must be cleared during a clean reboot.
Download mode has to be enabled by including qcom_scm.download_mode=1 on
the command line.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds documentation describing a device tree binding for the
coreboot firmware. It is meant to be dynamically added during boot and
contains address definitions for the coreboot table (a list of
variable-sized descriptors providing information about various compile-
and run-time generated firmware parameters) and the CBMEM area (the
structure containing most run-time resident memory regions set up by
coreboot).
These definitions allow kernel drivers to easily access data contained
in and pointed to by these regions (such as coreboot's in-memory log).
(An example implementation can be seen in the following patch)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull "Qualcomm ARM Based Driver Updates for v4.10 - Part 2" from Andy Gross:
* Fixup QCOM SCM to support MSM8996
* tag 'qcom-drivers-for-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
firmware: qcom: scm: Return PTR_ERR when devm_clk_get fails
firmware: qcom: scm: Remove core, iface and bus clocks dependency
dt-bindings: firmware: scm: Add MSM8996 DT bindings
The BPMP implements some services which must be represented by separate
nodes. For example, it can provide access to certain I2C controllers,
and the I2C bindings represent each I2C controller as a device tree
node. Update the binding to describe how the BPMP supports this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
[treding@nvidia.com: renamed bpmp-i2c to i2c as per Rob]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra186 BPMP is also a provider of power domains. Enhance the
device tree binding to describe this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Boot and Power Management Processor (BPMP) is a co-processor found
in Tegra SoCs. It is designed to handle the early stages of the boot
process as well as to offload power management tasks (such as clocks,
resets, powergates, ...).
The binding document defines the resources that are used by the BPMP
firmware, which implements the interprocessor communication (IPC)
between the CPU and the BPMP.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
