This fixes at least 2 issues I have found with the UDP tunnel filter
configuration.
The first issue is the fact that the tunnels didn't have any sort of mutual
exclusion in place to prevent an update from racing with a user request to
add/remove a port. As such you could request to add and remove a port
before the port update code had a chance to respond which would result in a
very confusing result. To address it I have added 2 changes. First I added
the RTNL mutex wrapper around our updating of the pending, port, and
filter_index bits. Second I added logic so that we cannot use a port that
has a pending deletion since we need to free the space in hardware before
we can allow software to reuse it.
The second issue addressed is the fact that we were not recording the
actual filter index provided to us by the admin queue. As a result we were
deleting filters that were not associated with the actual filter we wanted
to delete. To fix that I added a filter_index member to the UDP port
tracking structure.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the problem where each MTU change turns TSO,
GSO and GRO on from off state.
Now when TSO, GSO or GRO is turned off, MTU change does not
turn them on.
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The advertising 10G LR mode should be possible to set
but in the function i40e_set_link_ksettings() check for this
is missed. This patch adds check for 10000baseLR_Full
flag for 10G modes.
Signed-off-by: Jakub Pawlak <jakub.pawlak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previous method for reading LLDP config was based on hard-coded
offsets. It happened to work, because of structured architecture of
the NVM memory. In the new approach, known as FLAT, we need to
calculate the absolute address, instead of using relative values.
Needed defines for memory location were added.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent versions of the Linux kernel now warn about incorrect parameter
definitions for function comments. Fix up several function comments to
correctly reflect the current function arguments. This cleans up the
warnings and helps ensure our documentation is accurate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
use helper __skb_put_zero to replace the pattern of __skb_put() && memset()
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i40evf_add_vlan() is never called in atomic context.
i40evf_add_vlan() is only called by i40evf_vlan_rx_add_vid(),
which is only set as ".ndo_vlan_rx_add_vid" in struct net_device_ops.
".ndo_vlan_rx_add_vid" is not called in atomic context.
Despite never getting called from atomic context,
i40evf_add_vlan() calls kzalloc() with GFP_ATOMIC,
which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL,
which can sleep and improve the possibility of sucessful allocation.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The chip-specific init code includes quite some calls which are
identical for all chips. So move these calls to tp->hw_start().
In addition move rtl_set_rx_max_size() a little to make sure it's
defined before it's used. Unfortunately the diff generated by git
is a little bit hard to read.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__dev_open() calls the ndo_set_rx_mode callback anyway, so we don't
have to do it here too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently done:
- if mac_version in (01, 02, 03, 04)
RTL_W8(tp, ChipCmd, CmdTxEnb | CmdRxEnb);
- if mac_version in (01, 02, 03, 04)
rtl_set_rx_tx_config_registers(tp);
- if mac_version not in (01, 02, 03, 04)
RTL_W8(tp, ChipCmd, CmdTxEnb | CmdRxEnb);
rtl_set_rx_tx_config_registers(tp);
So we do exactly the same independent of chip version and can simplify
the code.
In addition remove the call to rtl_init_rxcfg(), it's called in
rtl_init_one() already and the set bits are never touched later.
rtl_init_8168/8101 don't include this call either.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both quirk masks are the same, so we can merge them. The quirk mask
includes most bits so it's actually easier to define a mask with
the bits to keep.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tp->cp_cmd is supposed to reflect the current value of the CplusCmd
register. Several (quite old) changes however directly change this
register w/o updating tp->cp_cmd. Also we have places in the code
reading this register where we could use the cached value.
In addition:
- Properly initialize tp->cmd with the register value.
- In rtl_hw_start_8169 remove one setting of PCIMulRW because it's
set unconditionally anyway a few lines later.
- In rtl_hw_start_8168 properly mask out the INTT bits before
setting INTT_1. So far we rely on both bits being zero.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__rtl8169_set_features is used in rtl8169_set_features only, so we
can inline it. In addition:
- Remove check (features ^ dev->features), __netdev_update_features
check's already that requested features differ from current ones.
- Don't mask out unsupported flags, there's no benefit in it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RxChkSum and RxVlan aren't touched outside __rtl8169_set_features
(except in probe), so they are always in sync with dev->features.
And the RxConfig flags are set in rtl_set_rx_mode() which is
called via dev_set_rx_mode() from __dev_open().
Therefore we can safely remove this call.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revision 7 of PCIe dongle interface increases the item size of tx and rx
complete rings to accommodate extra payload for new feature. This patch
simply bump up the size of these two rings without adding the support
for utilizing the new space. This makes brcmfmac compatible with rev7
firmware.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The enum nl80211_band used to retrieve wiphy->bands is the same as
wiphy->bands->band which is checked by wiphy_register(). So it can be used
directly as parameter of ieee80211_channel_to_frequency().
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a potential execution path in which variable ret is returned
without being properly initialized previously.
Fix this by storing the value returned by function
rsi_usb_master_reg_write into _ret_.
Addresses-Coverity-ID: 1468407 ("Uninitialized scalar variable")
Fixes: 16d3bb7b2f ("rsi: disable fw watchdog timer during reset")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function rsi_hal_key_config returns before reaching code at line
922 if (status), hence this code is structurally dead.
Fix this by storing the value returned by rsi_hal_load_key
into _status_ for its further evaluation and use.
Addresses-Coverity-ID: 1468409 ("Structurally dead code")
Fixes: 4fd6c4762f ("rsi: roaming enhancements")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pm_runtime handles sdio power on and power off transitions.
An old workaround for trying to control the power explicitly from the
driver was in fact causing failures on suspend/resume as the mmc layer
already power the module on resume.
In case of resume pm_runtime_get sync returns a positive device's usage
count causing the driver to try an re-initialize an already initialized
device. This was causing sdio bus failure on resume.
Remove this manual power on/off sequence as it is in-fact not needed.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
dma_tx_fragment() is never called in atomic context.
dma_tx_fragment() is only called by b43legacy_dma_tx(), which is
only called by b43legacy_tx_work().
b43legacy_tx_work() is only set a parameter of INIT_WORK() in
b43legacy_wireless_init().
Despite never getting called from atomic context,
dma_tx_fragment() calls alloc_skb() with GFP_ATOMIC,
which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL,
which can sleep and improve the possibility of sucessful allocation.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During changing virtual interface, keep using previous net device
mac address.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When interface type changed, firmware using a new connction pointer.
We need Re-configure the mac address.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For user configurated mac address, directly set to firmware with no change.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The check within mt76_txq_send_burst is not enough, as it happens after
a first frame has already been queued up
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avoids having the tid or station entry disappear prematurely.
Also cancel the reorder work earlier to avoid further processing delayed
by waiting for the lock to be released
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a spinlock in mt76_rx_complete. Without this, multiple stats updates
could happen in parallel, which can lead to deadlocks. There are
probably more corner cases fixed by this change.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix is_mt7612 routine since asic version is set in mt76_dev revision
field and not in mt76x2_dev one.
Moreover remove mt76x2_dev rev field since it is never used in the
driver
Fixes: 7bc04215a6 ('mt76: add driver code for MT76x2e')
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The code in the fallback path has supported XDP in conjunction with the Tx
traffic classification for TCs for over a year now. So instead of just
calling skb_tx_hash for every packet we are better off using the fallback
since that will record the Tx queue to the socket and then that can be used
instead of having to recompute the hash every time.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
