In coex mode, observed hibernate resume is not working properly, as the
hibernate_resume flag is not getting reset in rsi_coex_recv_pkt(),
when common card ready indication received from firmware. Hence resetting
hibernate_resume flag in this function.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the "poweroff" command is executed after wowlan enabled, we have
observed a system crash. In the system "poweroff" sequence, network-manager
is sent to inactive state by cleaning up the network interfaces, using
rsi_mac80211_remove_interface() and when driver tries to access those
network interfaces in rsi_wowlan_config() which was invoked by SDIO
shutdown, results in a crash. Added a NULL check before accessing the
network interfaces in rsi_wowlan_config().
Signed-off-by: Sanjay Kumar Konduri <sanjay.konduri@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmfmac is a FullMAC driver and it implements/uses cfg80211 interface
for stations management. At the same time it doesn't receive or pass up
management frames.
This flag indicates that authenticator doesn't have to subscribe to or
handle management frames. Some authenticators (e.g. hostapd) were
working with brcmfmac thanks to some extra assumptions. This commit
clears up the situation.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Adds support for matching flows based on tunnel VNI value.
Introduces fw APIs for allocating/removing MPS entries related
to encapsulation. And uses the same while adding/deleting filters
for offloading flows based on tunnel VNI match.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gen bits must be read first from (resp. written last to) DMA memory.
The proper way to enforce this on Linux is to call dma_rmb() (resp.
dma_wmb()).
Signed-off-by: Regis Duchesne <hpreg@vmware.com>
Acked-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA mask must be set before, not after, the first DMA map operation, or
the first DMA map operation could in theory fail on some systems.
Fixes: b0eb57cb97 ("VMXNET3: Add support for virtual IOMMU")
Signed-off-by: Regis Duchesne <hpreg@vmware.com>
Acked-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Earlier code of doing bitwise AND with field width bits was wrong.
Instead, simplify code to calculate ntuple_mask based on supplied
fields and then compare with mask configured in hw - which is the
correct and simpler way to validate ntuple mask.
Fixes: 3eb8b62d5a ("cxgb4: add support to create hash-filters via tc-flower offload")
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MLX5E_TEST_BIT macro is the same as the already existent test_bit,
remove it and replace all usages.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Make the code more clear by replacing the existing code with __set_bit.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Report all channels which got timeout on posting the minimal number of
RX WQEs and not only the first one. Avoid busy wait on every channel,
when one of the RQs check got timeout, poll once for the remaining RQs.
In addition, add channel index to log when failed to get min RX WQEs
This info is needed in order to debug in case of dysfunctional channel.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
For example:
tc filter add dev ens2f0_0 parent ffff: flower skip_sw action drop
Note that for eswitch flows, we still always match on the source port.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduce levels of matching on headers of offloaded flows
(none, L2, L3, L4) that follow the inline mode levels.
This is pre-step for us to offload flows without any
matches on headers.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Set the initial value to none instead of L2, and set to L2
where the previous initial value was assumed. Make sure to
parse L2 matches before L3 matches and L3 before L4.
This is a pre-step to get the match level for more purposes
other than the validating the needed vs. actual inline level.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Range of LRO number of segments fits in u8.
Also, bring initialization and declaration together to
save code.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
It's redundant to continue the loop if we found one flow whose lastuse value
being newer than the last one we reported, since this is enough for us to
trigger a NUD update (neigh_event_send()).
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In delete vlan flow an extra call to mlx5e_vport_context_update_vlans
was added by mistake, remove it.
Fixes: 86d722ad2c ("net/mlx5: Use flow steering infrastructure for mlx5_en")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Gal Pressman <galp@mellanox.com>
We no longer require a check for cxgb4 to be MASTER
when configuring SRIOV, It was required when we had
module parameter to instantiate vf.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When resolving a path that the packet will take after being encapsulated
in mirror-to-gretap scenarios, one of the devices en route could be a
LAG. In that case, mirror to first up slave that corresponds to a front
panel port.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid exiting the function with a lingering sysfs file (if the first
call to device_create_file() fails while the second succeeds), and avoid
calling devlink_port_unregister() twice.
In other words, either mlx4_init_port_info() succeeds and returns zero, or
it fails, returns non-zero, and requires no cleanup.
Fixes: 096335b3f9 ("mlx4_core: Allow dynamic MTU configuration for IB ports")
Signed-off-by: Tarick Bedeir <tarick@google.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(...)).
drivers/net/ethernet/ti/cpts.c:567:9-16: WARNING: ERR_CAST can be used with cpts->refclk
Generated by: scripts/coccinelle/api/err_cast.cocci
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Allwinner R40 SoC has the EMAC controller supported by dwmac-sun8i.
It is named "GMAC", while EMAC refers to the 10/100 Mbps Ethernet
controller supported by sun4i-emac. The controller is the same, but
the R40 has the glue layer controls in the clock control unit (CCU),
with a reduced RX delay chain, and no TX delay chain.
This patch adds support for it using the framework laid out by previous
patches to map the differences.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the R40 SoC, the RX delay chain only has a range of 0~7 (hundred
picoseconds), instead of 0~31. Also the TX delay chain is completely
absent.
This patch adds support for different ranges by adding per-compatible
maximum values in the variant data. A maximum of 0 indicates that the
delay chain is not supported or absent.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the Allwinner R40 SoC, the "GMAC clock" register is in the CCU
address space. Using a standard syscon to access it provides no
coordination with the CCU driver for register access. Neither does
it prevent this and other drivers from accessing other, maybe critical,
clock control registers. On other SoCs, the register is in the "system
control" address space, which might also contain controls for mapping
SRAM to devices or the CPU. This hardware has the same issues.
Instead, for these types of setups, we let the device containing the
control register create a regmap tied to it. We can then get the device
from the existing syscon phandle, and retrieve the regmap with
dev_get_regmap().
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the Allwinner R40, the "GMAC clock" register is located in the CCU
block, at a different register address than the other SoCs that have
it in the "system control" block.
This patch converts the use of regmap to regmap_field for mapping and
accessing the syscon register, so we can have the register address in
the variants data, and not in the actual register manipulation code.
This patch only converts regmap_read() and regmap_write() calls to
regmap_field_read() and regmap_field_write() calls. There are some
places where it might make sense to switch to regmap_field_update_bits(),
but this is not done here to keep the patch simple.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the Global 1 specific setup function only setup the statistics
unit, kill it in favor of a mv88e6xxx_stats_setup function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All Marvell switch families except 88E6390 have direct registers in
Global 1 for IEEE and IP priorities override mapping. The 88E6390 uses
indirect tables instead.
Add .ieee_pri_map and .ip_pri_map ops to distinct that and call them
from a mv88e6xxx_pri_setup helper. Only non-6390 are concerned ATM.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6390 model has its histogram mode bits moved in the
Global 1 Control 2 register. Use the previously introduced
mv88e6xxx_g1_ctl2_mask helper to set them.
At the same time complete the documentation of the said register.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We used to initialize ptr_ring during TUNSETIFF, this is because its
size depends on the tx_queue_len of netdevice. And we try to clean it
up when socket were detached from netdevice. A race were spotted when
trying to do uninit during a read which will lead a use after free for
pointer ring. Solving this by always initialize a zero size ptr_ring
in open() and do resizing during TUNSETIFF, and then we can safely do
cleanup during close(). With this, there's no need for the workaround
that was introduced by commit 4df0bfc799 ("tun: fix a memory leak
for tfile->tx_array").
Reported-by: syzbot+e8b902c3c3fadf0a9dba@syzkaller.appspotmail.com
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Fixes: 1576d98605 ("tun: switch to use skb array for tx")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-05-14
This series contains updates to virtchnl, i40e and i40evf.
Bruce cleans up whitespace and unnecessary parentheses in virtchnl.
Jake does a number of stat cleanups in the i40e driver, including
cleanup of code indentation, whitespace issues, remove duplicate stats,
fix grammar in code comment and general spring cleaning of the
statistics code.
Patryk fixes an issue where we recalculate vectors left and vectors
wanted but do not take into account the reduced number of queue pairs
per VSI.
Harshitha adds tx_busy stat to ethtool stats to track the number of
times we return NETDEV_TX_BUSY to the stack during transmit.
Paweł fixes a potential system crash when unloading the VF driver after
a hardware reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Register callback to collect hardware/firmware dumps in second kernel
before hardware/firmware is initialized. The dumps for each device
will be available as elf notes in /proc/vmcore in second kernel.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ath10k testmode uses request_firmware_direct() in order to avoid
producing firmware load warnings. Disabling the fallback mechanism was a
side effect of disabling warnings.
We now have a new API that allows us to avoid warnings while keeping the
fallback mechanism enabled. So use that instead.
Signed-off-by: Andres Rodriguez <andresx7@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
This patch fixes a hardware reset support in VF driver.
It is needed because when a hardware reset is detected
adapter->state is in __I40EVF_RESETTING state before
i40evf_reset_task is called. Without this patch
unloading VF driver after a hardware reset ends
with a system crash.
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit bbc4e7d273 ("i40e: fix race condition with PTP_TX_IN_PROGRESS
bits") we modified the code which handles Tx timestamps so that we would
clear the progress bit as soon as possible.
A later commit 0bc0706b46 ("i40e: check for Tx timestamp timeouts during
watchdog") introduced similar code for detecting and handling cleanup of
a blocked Tx timestamp. This code did not use the same pattern for cleaning
up the skb.
Update this code to wait to free the skb until after the bit lock is
free, by first setting the ptp_tx_skb to NULL and clearing the lock.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't really need to have separate definitions for MAX_QUEUES and
I40EVF_MAX_REQ_QUEUES, since we'll always be limited by how many queues
we request anyways. If we haven't enabled requesting the maximum number
of queues, there's no reason to have our call to alloc_etherdev_mq
actually pass the higher value, since we'd never enable those queues
anyways.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the tx_busy stat to the ethtool stats. The tx_busy
stat tracks the number of times we return NETDEV_TX_BUSY to the stack
during transmit.
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a recalculation of number of MSI-X
vectors for VMDq in the case where we have less
vectors available than we would want to reserve for
VMDq.
It fixes the issue where we recalculate vectors left
and vectors wanted but we didn't take into account
the reduced number of queue pairs per VSI.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A future patch is going to refactor some of the ethtool statistic code.
To keep the patches easy to review, cleanup some of the indentation used
for macro definitions first.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The pfc related priority stats are already handled separately as these
stats are actually arrays of length I40E_MAX_USER_PRIORITY. Thus,
including them within i40e_gstrings_stats will just duplicate data.
Worse, the sizeof will be incorrect, as it will be the total size of the
stat arrays, which in this case is 8 * sizeof(u64), so we will only copy
the stat contents as if they were a u32.
Since we already correctly handle these stats else where, remove them
from the i40e_gstrings_stats.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use a separate function to calculate the number of stats for
a particular device. This helps reduce the clutter in
i40e_get_sset_count().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
