Reviewing the result of what was just added for Kconfig, we made a poor
choice. It worked well for full kernel builds, but not so much for how
it would be deployed on a distro.
Here's the final result:
- lpfc will compile in NVME initiator and/or NVME target support based
on whether the kernel has the corresponding subsystem support.
Kconfig is not used to drive this specifically for lpfc.
- There is a module parameter, lpfc_enable_fc4_type, that indicates
whether the ports will do FCP-only or FCP & NVME (NVME-only not yet
possible due to dependency on fc transport). As FCP & NVME divvys up
exchange resources, and given NVME will not be often initially, the
default is changed to FCP only.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Without apriori understanding of what the define is, the name gives
a very different impression of what it is (a max delay value
for an EQ). Rename the define so it reflects what it is: the number
of EQ IDs that can be set in one instance of the MODIFY_EQ_DELAY
mbx command.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A previous change unilaterally removed the hba reset entry point
from the sli3 host template. This was done to allow tape devices
being used for back up from being removed. Why was this done ?
When there was non-responding device on the fabric, the error
escalation policy would escalate to the reset handler. When the
reset handler was called, it would reset the adapter, dropping
link, thus logging out and terminating all i/o's - on any target.
If there was a tape device on the same adapter that wasn't in
error, it would kill the tape i/o's, effectively killing the
tape device state. With the reset point removed, the adapter
reset avoided the fabric logout, allowing the other devices to
continue to operate unaffected. A hack - yes. Hint: we really
need a transport I_T nexus reset callback added to the eh process
(in between the SCSI target reset and hba reset points), so a
fc logout could occur to the one bad target only and stop the error
escalation process.
This patch commonizes the approach so it can be used for sli3 and sli4
adapters, but mandates the admin, via module parameter, specifically
identify which adapters the resets are to be removed for. Additionally,
bus_reset, which sends Target Reset TMFs to all targets, is also removed
from the template as it too has the same effect as the adapter reset.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull more SCSI updates from James Bottomley:
"This is the set of stuff that didn't quite make the initial pull and a
set of fixes for stuff which did.
The new stuff is basically lpfc (nvme), qedi and aacraid. The fixes
cover a lot of previously submitted stuff, the most important of which
probably covers some of the failing irq vectors allocation and other
fallout from having the SCSI command allocated as part of the block
allocation functions"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (59 commits)
scsi: qedi: Fix memory leak in tmf response processing.
scsi: aacraid: remove redundant zero check on ret
scsi: lpfc: use proper format string for dma_addr_t
scsi: lpfc: use div_u64 for 64-bit division
scsi: mac_scsi: Fix MAC_SCSI=m option when SCSI=m
scsi: cciss: correct check map error.
scsi: qla2xxx: fix spelling mistake: "seperator" -> "separator"
scsi: aacraid: Fixed expander hotplug for SMART family
scsi: mpt3sas: switch to pci_alloc_irq_vectors
scsi: qedf: fixup compilation warning about atomic_t usage
scsi: remove scsi_execute_req_flags
scsi: merge __scsi_execute into scsi_execute
scsi: simplify scsi_execute_req_flags
scsi: make the sense header argument to scsi_test_unit_ready mandatory
scsi: sd: improve TUR handling in sd_check_events
scsi: always zero sshdr in scsi_normalize_sense
scsi: scsi_dh_emc: return success in clariion_std_inquiry()
scsi: fix memory leak of sdpk on when gd fails to allocate
scsi: sd: make sd_devt_release() static
scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.
...
NVME Target: Receive buffer updates
Allocates buffer pools and configures adapter interfaces to handle
receive buffer (asynchronous FCP CMD ius, first burst data)
from the adapter. Splits by protocol, etc.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME Target: Base modifications
This set of patches adds the base modifications for NVME target support
The base modifications consist of:
- Additional module parameters or configuration tuning
- Enablement of configuration mode for NVME target. Ties into the
queueing model put into place by the initiator basemods patches.
- Target-specific buffer pools, dma pools, sgl pools
[mkp: fixed space at end of file]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME Initiator: Base modifications
This patch adds base modifications for NVME initiator support.
The base modifications consist of:
- Formal split of SLI3 rings from SLI-4 WQs (sometimes referred to as
rings as well) as implementation now widely varies between the two.
- Addition of configuration modes:
SCSI initiator only; NVME initiator only; NVME target only; and
SCSI and NVME initiator.
The configuration mode drives overall adapter configuration,
offloads enabled, and resource splits.
NVME support is only available on SLI-4 devices and newer fw.
- Implements the following based on configuration mode:
- Exchange resources are split by protocol; Obviously, if only
1 mode, then no split occurs. Default is 50/50. module attribute
allows tuning.
- Pools and config parameters are separated per-protocol
- Each protocol has it's own set of queues, but share interrupt
vectors.
SCSI:
SLI3 devices have few queues and the original style of queue
allocation remains.
SLI4 devices piggy back on an "io-channel" concept that
eventually needs to merge with scsi-mq/blk-mq support (it is
underway). For now, the paradigm continues as it existed
prior. io channel allocates N msix and N WQs (N=4 default)
and either round robins or uses cpu # modulo N for scheduling.
A bunch of module parameters allow the configuration to be
tuned.
NVME (initiator):
Allocates an msix per cpu (or whatever pci_alloc_irq_vectors
gets)
Allocates a WQ per cpu, and maps the WQs to msix on a WQ #
modulo msix vector count basis.
Module parameters exist to cap/control the config if desired.
- Each protocol has its own buffer and dma pools.
I apologize for the size of the patch.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
----
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This contains code cleanups that were in the prior patch set.
This allows better review of real changes later.
minor code cleanups:
fix indentation, punctuation, line length
addition/reduction of whitespace
remove unneeded parens, braces
lpfc_debugfs_nodelist_data: print as u64 rather than byte by byte
covert printk(KERN_ERR to pr_err
small print string deltas
use num_present_cpus() rather than count them
comment updates
rctl/type names moved to module variable, not on stack
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When I reversed the patch to re-add the lpfc_soft_wwn parameter feature,
it re-added code that had a long-standing bug. (that's what I get I
guess :)
As Dan Carpenter pointed out - error checks looked at wrong polarity. 0
is success, -errno is failure. Updated checks.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The lpfc 11.2.0.4 patch set deprecated, by removing, the lpfc_soft_wwn
parameter support.
This patch reinstates support, but adds a warning in the enablement of
the feature that indicates Broadcom (Emulex) does not support the
feature.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Synchronize link speed with boot driver
Link speed settings set by the boot driver are reported by the hw.
Driver will attempt to read them, and if set, will respect their
values.
The driver can override the settings with its own if instructed by
user space (via bsg), with the new values being picked up by the
boot driver.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When building with -Wextra, we get a lot of warnings for the lpfc driver
concerning expressions that are always true, starting with:
drivers/scsi/lpfc/lpfc_attr.c: In function 'lpfc_enable_npiv_init':
drivers/scsi/lpfc/lpfc_attr.c:2786:77: error: comparison of unsigned expression >= 0 is always true [-Werror=type-limits]
drivers/scsi/lpfc/lpfc_attr.c: In function 'lpfc_enable_rrq_init':
drivers/scsi/lpfc/lpfc_attr.c:2802:76: error: comparison of unsigned expression >= 0 is always true [-Werror=type-limits]
drivers/scsi/lpfc/lpfc_attr.c: In function 'lpfc_suppress_link_up_init':
drivers/scsi/lpfc/lpfc_attr.c:2812:2050: error: comparison of unsigned expression >= 0 is always true [-Werror=type-limits]
drivers/scsi/lpfc/lpfc_attr.c: In function 'lpfc_log_verbose_init':
drivers/scsi/lpfc/lpfc_attr.c:3064:1930: error: comparison of unsigned expression >= 0 is always true [-Werror=type-limits]
The code works as intended, but it would be nice to shut up the warning
so we don't clutter up build logs with this. Using a separate inline
function for it makes it clear to the compiler that the comparison is
necessary in the caller but still lets it do the constant-folding.
[mkp: fix typo]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modularize, cleanup, add comments - for FDMI code in driver
Note: I don't like the comments with leading # - but as we have a lot if
present, I'm deferring to handle it in one big fix later.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixed Low priority issues from lpfc given by fortify source code scan.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: Dick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Now that we're using 64-bit LUNs internally we need to increase
the size of max_luns to 64 bits, too.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
