This patch introduces a new mesh configuration parameter "ht_opmode" and will
allow user to check the current HT protection mode selected. Users could
configure the protection mode by the command "iw mesh_iface set mesh_param
mesh_ht_protection_mode=2". The default protection mode of mesh is set to
non-HT mixed mode.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Reviewed-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we have protection enabled, allow non-HT and HT20 stations to peer
with HT40+/- stations. Peering is still disallowed for HT40+/- mismatch.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Reviewed-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Section 9.23.3.5 of IEEE 80211s standard describes the protection rules for
HT mesh STA in a MBSS. Three HT protection modes are supported for now:
non-HT mixed mode - is selected if any non-HT peers are present in our MBSS.
20MHz-protection mode - is selected if all peers in our 20/40MHz MBSS support
HT and atleast one HT20 peer is present.
no-protection mode - is selected otherwise.
This is a limited implementation of 9.23.3.5, which only considers mesh peers
when determining the HT protection mode. Station's channel_type needs to be
maintained.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Reviewed-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the BSS table is organized in a RB tree, the BSSs need to be
comparable. This means that we must define a < and > operator to
the BSS object.
compare_ethr_addr isn't enough since it returns only a binary value.
Since Felix's
cfg80211: use compare_ether_addr on MAC addresses instead of memcmp
Because of the constant size and guaranteed 16 bit alignment, the inline
compare_ether_addr function is much cheaper than calling memcmp.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BSS table is corrupted: rb_find_bss can't find the bss.
As a result BSSes are duplicated in the BSS table, and we get stuck
while probing an AP before associating (in STA mode).
Change-Id: I85928756f4328028230832c1565ece7f412f3843
CC: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The signal and noise are forced to be positive since ethtool
deals in unsigned 64-bit values and this number should be human
readable. This gives easy access to some of the data formerly
exposed in the deprecated /proc/net/wireless file.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds hooks to call into the driver to get additional
stats for the ethtool API.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This lets ethtool print out stats related to stations
connected to the interface. Does not yet get stats
from the underlying driver.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a mesh peer indicates it is operating as 20MHz-only in its HT
operation IE, have the rate control algorithm respect this by disabling
the equivalent bit in the ieee80211_sta HT capabilities.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers need the station rate info when inserting a new sta_info. The
patch "mac80211: refactor mesh peer initialization" wrongly assumed the
rate info could be applied after insertion. After further review, this
is clearly not the case.
This fixes a regression where HT parameters were not applied before
inserting the sta_info, causing performance degradation.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rate control updation never be called on 2040 BSS change.
The station should update its rate control on receiving beacon
with different HT mode in the HT operation IE. Not doing so,
leads to sending frames with higher(ht40) rates whereas AP is
operating in lower mode (ht20).
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes ip_queue support which was marked as obsolete
years ago. The nfnetlink_queue modules provides more advanced
user-space packet queueing mechanism.
This patch also removes capability code included in SELinux that
refers to ip_queue. Otherwise, we break compilation.
Several warning has been sent regarding this to the mailing list
in the past month without anyone rising the hand to stop this
with some strong argument.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Explicit helper attachment via the CT target is broken with NAT
if non-standard ports are used. This problem was hidden behind
the automatic helper assignment routine. Thus, it becomes more
noticeable now that we can disable the automatic helper assignment
with Eric Leblond's:
9e8ac5a netfilter: nf_ct_helper: allow to disable automatic helper assignment
Basically, nf_conntrack_alter_reply asks for looking up the helper
up if NAT is enabled. Unfortunately, we don't have the conntrack
template at that point anymore.
Since we don't want to rely on the automatic helper assignment,
we can skip the second look-up and stick to the helper that was
attached by iptables. With the CT target, the user is in full
control of helper attachment, thus, the policy is to trust what
the user explicitly configures via iptables (no automatic magic
anymore).
Interestingly, this bug was hidden by the automatic helper look-up
code. But it can be easily trigger if you attach the helper in
a non-standard port, eg.
iptables -I PREROUTING -t raw -p tcp --dport 8888 \
-j CT --helper ftp
And you disabled the automatic helper assignment.
I added the IPS_HELPER_BIT that allows us to differenciate between
a helper that has been explicitly attached and those that have been
automatically assigned. I didn't come up with a better solution
(having backward compatibility in mind).
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This refreshes the "timeout" attribute in existing expectations if one is
given.
The use case for this would be for userspace helpers to extend the lifetime
of the expectation when requested, as this is not possible right now
without deleting/recreating the expectation.
I use this specifically for forwarding DCERPC traffic through:
DCERPC has a port mapper daemon that chooses a (seemingly) random port for
future traffic to go to. We expect this traffic (with a reasonable
timeout), but sometimes the port mapper will tell the client to continue
using the same port. This allows us to extend the expectation accordingly.
Signed-off-by: Kelvie Wong <kelvie@ieee.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
To build ip_vs as a module sysctl_rmem_max and sysctl_wmem_max
needs to be exported.
The dependency was added by "ipvs: wakeup master thread" patch.
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Functions not referenced outside of a source file should be marked
static to prevent it from being exposed globally.
This quiets the sparse warnings:
warning: symbol '__ipvs_proto_data_get' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Functions not referenced outside of a source file should be marked
static to prevent it from being exposed globally.
This quiets the sparse warnings:
warning: symbol 'ip_vs_ftp_init' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
cp->flags is marked volatile but ip_vs_bind_dest
can safely modify the flags, so save some CPU cycles by
using temp variable.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Allow master and backup servers to use many threads
for sync traffic. Add sysctl var "sync_ports" to define the
number of threads. Every thread will use single UDP port,
thread 0 will use the default port 8848 while last thread
will use port 8848+sync_ports-1.
The sync traffic for connections is scheduled to many
master threads based on the cp address but one connection is
always assigned to same thread to avoid reordering of the
sync messages.
Remove ip_vs_sync_switch_mode because this check
for sync mode change is still risky. Instead, check for mode
change under sync_buff_lock.
Make sure the backup socks do not block on reading.
Special thanks to Aleksey Chudov for helping in all tests.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Tested-by: Aleksey Chudov <aleksey.chudov@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Add two new sysctl vars to control the sync rate with the
main idea to reduce the rate for connection templates because
currently it depends on the packet rate for controlled connections.
This mechanism should be useful also for normal connections
with high traffic.
sync_refresh_period: in seconds, difference in reported connection
timer that triggers new sync message. It can be used to
avoid sync messages for the specified period (or half of
the connection timeout if it is lower) if connection state
is not changed from last sync.
sync_retries: integer, 0..3, defines sync retries with period of
sync_refresh_period/8. Useful to protect against loss of
sync messages.
Allow sysctl_sync_threshold to be used with
sysctl_sync_period=0, so that only single sync message is sent
if sync_refresh_period is also 0.
Add new field "sync_endtime" in connection structure to
hold the reported time when connection expires. The 2 lowest
bits will represent the retry count.
As the sysctl_sync_period now can be 0 use ACCESS_ONCE to
avoid division by zero.
Special thanks to Aleksey Chudov for being patient with me,
for his extensive reports and helping in all tests.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Tested-by: Aleksey Chudov <aleksey.chudov@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
High rate of sync messages in master can lead to
overflowing the socket buffer and dropping the messages.
Fixed sleep of 1 second without wakeup events is not suitable
for loaded masters,
Use delayed_work to schedule sending for queued messages
and limit the delay to IPVS_SYNC_SEND_DELAY (20ms). This will
reduce the rate of wakeups but to avoid sending long bursts we
wakeup the master thread after IPVS_SYNC_WAKEUP_RATE (8) messages.
Add hard limit for the queued messages before sending
by using "sync_qlen_max" sysctl var. It defaults to 1/32 of
the memory pages but actually represents number of messages.
It will protect us from allocating large parts of memory
when the sending rate is lower than the queuing rate.
As suggested by Pablo, add new sysctl var
"sync_sock_size" to configure the SNDBUF (master) or
RCVBUF (slave) socket limit. Default value is 0 (preserve
system defaults).
Change the master thread to detect and block on
SNDBUF overflow, so that we do not drop messages when
the socket limit is low but the sync_qlen_max limit is
not reached. On ENOBUFS or other errors just drop the
messages.
Change master thread to enter TASK_INTERRUPTIBLE
state early, so that we do not miss wakeups due to messages or
kthread_should_stop event.
Thanks to Pablo Neira Ayuso for his valuable feedback!
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
As the goal is to mirror the inactconns/activeconns
counters in the backup server, make sure the cp->flags are
updated even if cp is still not bound to dest. If cp->flags
are not updated ip_vs_bind_dest will rely only on the initial
flags when updating the counters. To avoid mistakes and
complicated checks for protocol state rely only on the
IP_VS_CONN_F_INACTIVE bit when updating the counters.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Tested-by: Aleksey Chudov <aleksey.chudov@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Initially, when the synced connection is created we
use the forwarding method provided by master but once we
bind to destination it can be changed. As result, we must
update the application and the transmitter.
As ip_vs_try_bind_dest is called always for connections
that require dest binding, there is no need to validate the
cp and dest pointers.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
As the IP_VS_CONN_F_INACTIVE bit is properly set
in cp->flags for all kind of connections we do not need to
add special checks for synced connections when updating
the activeconns/inactconns counters for first time. Now
logic will look just like in ip_vs_unbind_dest.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
As IP_VS_CONN_F_NOOUTPUT is derived from the
forwarding method we should get it from conn_flags just
like we do it for IP_VS_CONN_F_FWD_MASK bits when binding
to real server.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Use GFP_KERNEL instead of GFP_ATOMIC when registering an ipvs protocol.
This is safe since it will always run from a process context.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Schedulers are initialized and bound to services only
on commands.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Schedulers are initialized and bound to services only
on commands.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Schedulers are initialized and bound to services only
on commands.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Schedulers are initialized and bound to services only
on commands.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Schedulers are initialized and bound to services only
on commands.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
if net.bridge.bridge-nf-filter-vlan-tagged sysctl is enabled, bridge
netfilter removes the vlan header temporarily and then feeds the packet
to ip(6)tables.
When the new "bridge-nf-pass-vlan-input-device" sysctl is on
(default off), then bridge netfilter will also set the
in-interface to the vlan interface; if such an interface exists.
This is needed to make iptables REDIRECT target work with
"vlan-on-top-of-bridge" setups and to allow use of "iptables -i" to
match the vlan device name.
Also update Documentation with current brnf default settings.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch allows you to disable automatic conntrack helper
lookup based on TCP/UDP ports, eg.
echo 0 > /proc/sys/net/netfilter/nf_conntrack_helper
[ Note: flows that already got a helper will keep using it even
if automatic helper assignment has been disabled ]
Once this behaviour has been disabled, you have to explicitly
use the iptables CT target to attach helper to flows.
There are good reasons to stop supporting automatic helper
assignment, for further information, please read:
http://www.netfilter.org/news.html#2012-04-03
This patch also adds one message to inform that automatic helper
assignment is deprecated and it will be removed soon (this is
spotted only once, with the first flow that gets a helper attached
to make it as less annoying as possible).
Signed-off-by: Eric Leblond <eric@regit.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
* ret variable initialization removed as useless
* similar code strings concatenated and functions code
flow became more plain
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, struct mreq has not been recognized and it was worked with
as with struct in_addr. That means imr_multiaddr was copied to
imr_address. So do recognize struct mreq here and copy that correctly.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the kernel validates set TCP/UDP port actions, it looks at
the ports in the existing flow to make sure that the L4 header exists.
However, these actions always use the IPv4 version of the struct.
Following patch fixes this by checking for flow ip protocol first.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
If we get an error code from crush_do_rule(), print an error to the
console.
Reviewed-by: Alex Elder <elder@inktank.com>
Signed-off-by: Sage Weil <sage@inktank.com>
Fix the node weight lookup for tree buckets by using a correct accessor.
Reflects ceph.git commit d287ade5bcbdca82a3aef145b92924cf1e856733.
Reviewed-by: Alex Elder <elder@inktank.com>
Signed-off-by: Sage Weil <sage@inktank.com>
These were used for the ill-fated forcefeed feature. Remove them.
Reflects ceph.git commit ebdf80edfecfbd5a842b71fbe5732857994380c1.
Reviewed-by: Alex Elder <elder@inktank.com>
Signed-off-by: Sage Weil <sage@inktank.com>
Remove forcefeed functionality from CRUSH. This is an ugly misfeature that
is mostly useless and unused. Remove it.
Reflects ceph.git commit ed974b5000f2851207d860a651809af4a1867942.
Reviewed-by: Alex Elder <elder@inktank.com>
Signed-off-by: Sage Weil <sage@inktank.com>
Conflicts:
net/ceph/crush/mapper.c
Use a temporary variable here to avoid repeated array lookups and clean up
the code a bit.
This reflects ceph.git commit 6b5be27634ad307b471a5bf0db85c4f5c834885f.
Reviewed-by: Alex Elder <elder@inktank.com>
Signed-off-by: Sage Weil <sage@inktank.com>
If we get a map that doesn't make sense, error out or ignore the badness
instead of BUGging out. This reflects the ceph.git commits
9895f0bff7dc68e9b49b572613d242315fb11b6c and
8ded26472058d5205803f244c2f33cb6cb10de79.
Reviewed-by: Alex Elder <elder@inktank.com>
Signed-off-by: Sage Weil <sage@inktank.com>
This small adjustment reflects a change that was made in ceph.git commit
af6a9f30696c900a2a8bd7ae24e8ed15fb4964bb, about 6 months ago. An N-1
search is not exhaustive. Fixed ceph.git bug #1594.
Reviewed-by: Alex Elder <elder@inktank.com>
Signed-off-by: Sage Weil <sage@inktank.com>
Move various types from int -> __u32 (or similar), and add const as
appropriate.
This reflects changes that have been present in the userland implementation
for some time.
Reviewed-by: Alex Elder <elder@inktank.com>
Signed-off-by: Sage Weil <sage@inktank.com>
