The aim of this locking rework is that ioctls which a compositor should be
might call for every frame (set_cursor, page_flip, addfb, rmfb and
getfb/create_handle) should not be able to block on kms background
activities like output detection. And since each EDID read takes about
25ms (in the best case), that always means we'll drop at least one frame.
The solution is to add per-crtc locking for these ioctls, and restrict
background activities to only use the global lock. Change-the-world type
of events (modeset, dpms, ...) need to grab all locks.
Two tricky parts arose in the conversion:
- A lot of current code assumes that a kms fb object can't disappear while
holding the global lock, since the current code serializes fb
destruction with it. Hence proper lifetime management using the already
created refcounting for fbs need to be instantiated for all ioctls and
interfaces/users.
- The rmfb ioctl removes the to-be-deleted fb from all active users. But
unconditionally taking the global kms lock to do so introduces an
unacceptable potential stall point. And obviously changing the userspace
abi isn't on the table, either. Hence this conversion opportunistically
checks whether the rmfb ioctl holds the very last reference, which
guarantees that the fb isn't in active use on any crtc or plane (thanks
to the conversion to the new lifetime rules using proper refcounting).
Only if this is not the case will the code go through the slowpath and
grab all modeset locks. Sane compositors will never hit this path and so
avoid the stall, but userspace relying on these semantics will also not
break.
All these cases are exercised by the newly added subtests for the i-g-t
kms_flip, tested on a machine where a full detect cycle takes around 100
ms. It works, and no frames are dropped any more with these patches
applied. kms_flip also contains a special case to exercise the
above-describe rmfb slowpath.
* 'drm-kms-locking' of git://people.freedesktop.org/~danvet/drm-intel: (335 commits)
drm/fb_helper: check whether fbcon is bound
drm/doc: updates for new framebuffer lifetime rules
drm: don't hold crtc mutexes for connector ->detect callbacks
drm: only grab the crtc lock for pageflips
drm: optimize drm_framebuffer_remove
drm/vmwgfx: add proper framebuffer refcounting
drm/i915: dump refcount into framebuffer debugfs file
drm: refcounting for crtc framebuffers
drm: refcounting for sprite framebuffers
drm: fb refcounting for dirtyfb_ioctl
drm: don't take modeset locks in getfb ioctl
drm: push modeset_lock_all into ->fb_create driver callbacks
drm: nest modeset locks within fpriv->fbs_lock
drm: reference framebuffers which are on the idr
drm: revamp framebuffer cleanup interfaces
drm: create drm_framebuffer_lookup
drm: revamp locking around fb creation/destruction
drm: only take the crtc lock for ->cursor_move
drm: only take the crtc lock for ->cursor_set
drm: add per-crtc locks
...
We have two classes of framebuffer
- Created by the driver (atm only for fbdev), and the driver holds
onto the last reference count until destruction.
- Created by userspace and associated with a given fd. These
framebuffers will be reaped when their assoiciated fb is closed.
Now these two cases are set up differently, the framebuffers are on
different lists and hence destruction needs to clean up different
things. Also, for userspace framebuffers we remove them from any
current usage, whereas for internal framebuffers it is assumed that
the driver has done this already.
Long story short, we need two different ways to cleanup such drivers.
Three functions are involved in total:
- drm_framebuffer_remove: Convenience function which removes the fb
from all active usage and then drops the passed-in reference.
- drm_framebuffer_unregister_private: Will remove driver-private
framebuffers from relevant lists and drop the corresponding
references. Should be called for driver-private framebuffers before
dropping the last reference (or like for a lot of the drivers where
the fbdev is embedded someplace else, before doing the cleanup
manually).
- drm_framebuffer_cleanup: Final cleanup for both classes of fbs,
should be called by the driver's ->destroy callback once the last
reference is gone.
This patch just rolls out the new interfaces and updates all drivers
(by adding calls to drm_framebuffer_unregister_private at all the
right places)- no functional changes yet. Follow-on patches will move
drm core code around and update the lifetime management for
framebuffers, so that we are no longer required to keep framebuffers
alive by locking mode_config.mutex.
I've also updated the kerneldoc already.
vmwgfx seems to again be a bit special, at least I haven't figured out
how the fbdev support in that driver works. It smells like it's
external though.
v2: The i915 driver creates another private framebuffer in the
load-detect code. Adjust its cleanup code, too.
Reviewed-by: Rob Clark <rob@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And replace all fb lookups with it. Also add a WARN to
drm_mode_object_find since that is now no longer the blessed interface
to look up an fb. And add kerneldoc to both functions.
This only updates all callsites, but immediately drops the acquired
refence again. Hence all callers still rely on the fact that a mode fb
can't disappear while they're holding the struct mutex. Subsequent
patches will instate proper use of refcounts, and then rework the rmfb
and unref code to no longer serialize fb destruction with the
mode_config lock. We don't want that since otherwise a compositor
might end up stalling for a few frames in rmfb.
v2: Don't use kref_get_unless_zero - Greg KH doesn't like that kind of
interface.
Reviewed-by: Rob Clark <rob@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Well, at least step 1. The goal here is that framebuffer objects can
survive outside of the mode_config lock, with just a reference held
as protection. The first step to get there is to introduce a special
fb_lock which protects fb lookup, creation and destruction, to make
them appear atomic.
This new fb_lock can nest within the mode_config lock. But the idea is
(once the reference counting part is completed) that we only quickly
take that fb_lock to lookup a framebuffer and grab a reference,
without any other locks involved.
vmwgfx is the only driver which does framebuffer lookups itself, also
wrap those calls to drm_mode_object_find with the new lock.
Also protect the fb_list walking in i915 and omapdrm with the new lock.
As a slight complication there's also the list of user-created fbs
attached to the file private. The problem now is that at fclose() time
we need to walk that list, eventually do a modeset call to remove the
fb from active usage (and are required to be able to take the
mode_config lock), but in the end we need to grab the new fb_lock to
remove the fb from the list. The easiest solution is to add another
mutex to protect this per-file list.
Currently that new fbs_lock nests within the modeset locks and so
appears redudant. But later patches will switch around this sequence
so that taking the modeset locks in the fb destruction path is
optional in the fastpath. Ultimately the goal is that addfb and rmfb
do not require the mode_config lock, since otherwise they have the
potential to introduce stalls in the pageflip sequence of a compositor
(if the compositor e.g. switches to a fullscreen client or if it
enables a plane). But that requires a few more steps and hoops to jump
through.
Note that framebuffer creation/destruction is now double-protected -
once by the fb_lock and in parts by the idr_lock. The later would be
unnecessariy if framebuffers would have their own idr allocator. But
that's material for another patch (series).
v2: Properly initialize the fb->filp_head list in _init, otherwise the
newly added WARN to check whether the fb isn't on a fpriv list any
more will fail for driver-private objects.
v3: Fixup two error-case unlock bugs spotted by Richard Wilbur.
Reviewed-by: Rob Clark <rob@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
*drumroll*
The basic idea is to protect per-crtc state which can change without
touching the output configuration with separate mutexes, i.e. all the
input side state to a crtc like framebuffers, cursor settings or plane
configuration. Holding such a crtc lock gives a read-lock on all the
other crtc state which can be changed by e.g. a modeset.
All non-crtc state is still protected by the mode_config mutex.
Callers that need to change modeset state of a crtc (e.g. dpms or
set_mode) need to grab both the mode_config lock and nested within any
crtc locks.
Note that since there can only ever be one holder of the mode_config
lock we can grab the subordinate crtc locks in any order (if we need
to grab more than one of them). Lockdep can handle such nesting with
the mutex_lock_nest_lock call correctly.
With this functions that only touch connectors/encoders but not crtcs
only need to take the mode_config lock. The biggest such case is the
output probing, which means that we can now pageflip and move cursors
while the output probe code is reading an edid.
Most cases neatly fall into the three buckets:
- Only touches connectors and similar output state and so only needs
the mode_config lock.
- Touches the global configuration and so needs all locks.
- Only touches the crtc input side and so only needs the crtc lock.
But a few cases that need special consideration:
- Load detection which requires a crtc. The mode_config lock already
prevents a modeset change, so we can use any unused crtc as we like
to do load detection. The only thing to consider is that such
temporary state changes don't leak out to userspace through ioctls
that only take the crtc look (like a pageflip). Hence the load
detect code needs to grab the crtc of any output pipes it touches
(but only if it touches state used by the pageflip or cursor
ioctls).
- Atomic pageflip when moving planes. The first case is sane hw, where
planes have a fixed association with crtcs - nothing needs to be
done there. More insane^Wflexible hw needs to have plane->crtc
mapping which is separately protect with a lock that nests within
the crtc lock. If the plane is unused we can just assign it to the
current crtc and continue. But if a plane is already in use by
another crtc we can't just reassign it.
Two solution present themselves: Either go back to a slow-path which
takes all modeset locks, potentially incure quite a hefty delay. Or
simply disallowing such changes in one atomic pageflip - in general
the vblanks of two crtcs are not synced, so there's no sane way to
atomically flip such plane changes accross more than one crtc. I'd
heavily favour the later approach, going as far as mandating it as
part of the ABI of such a new a nuclear pageflip.
And if we _really_ want such semantics, we can always get them by
introducing another pageflip mutex between the mode_config.mutex and
the individual crtc locks. Pageflips crossing more than one crtc
would then need to take that lock first, to lock out concurrent
multi-crtc pageflips.
- Optimized global modeset operations: We could just take the
mode_config lock and then lazily lock all crtc which are affected by
a modeset operation. This has the advantage that pageflip could
continue unhampered on unaffected crtc. But if e.g. global resources
like plls need to be reassigned and so affect unrelated crtcs we can
still do that - nested locking works in any order.
This patch just adds the locks and takes them in drm_modeset_lock_all,
no real locking changes yet.
v2: Need to initialize the new lock in crtc_init and lock it righ
away, for otherwise the modeset_unlock_all below will try to unlock a
not-locked mutex.
Reviewed-by: Rob Clark <rob@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is the first step towards introducing the new modeset locking
scheme. The plan is to put helper functions into place at all the
right places step-by-step, so that the final patch to switch on the
new locking scheme doesn't need to touch every single driver.
This helper here will serve as the shotgun solutions for all places
where a more fine-grained locking isn't (yet) implemented.
v2: Fixup kerneldoc for unlock_all.
Reviewed-by: Rob Clark <rob@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The ia64 function "thread_matches()" has no users since commit
e868a55c2a ("[IA64] remove find_thread_for_addr()"). Remove it.
This allows us to make ptrace_check_attach() static to kernel/ptrace.c,
which is good since we'll need to change the semantics of it and fix up
all the callers.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With refcounting we need to adjust framebuffer refcounts at each
callsite - much easier to do if they all call the same little helper
function.
Reviewed-by: Rob Clark <rob@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- config_cleanup was confused: It claimed that callers need to hold
the modeset lock, but the connector|encoder_cleanup helpers grabbed
that themselves (note that crtc_cleanup did _not_ grab the modeset
lock). Which resulted in all drivers _not_ hodling the lock. Since
this is for single-threaded cleanup code, drop the requirement from
docs and also drop the lock_grabbing from all _cleanup functions.
- Kill the LOCKING section in the doctype, since clearly we're not
good enough to keep them up-to-date. And misleading locking
documentation is worse than useless (see e.g. the comment in the
vmgfx driver about the cleanup mess). And since for most functions
the very first line either grabs the lock or has a WARN_ON(!locked)
the documentation doesn't really add anything.
- Instead put in some effort into explaining the only two special
cases a bit better: config_init and config_cleanup are both called
from single-threaded setup/teardown code, so don't do any locking.
It's the driver's job though to enforce this.
- Where lacking, add a WARN_ON(!is_locked). Not many places though,
since locking around fbdev setup/teardown is through-roughly screwed
up, and so will break almost every single WARN annotation I've tried
to add.
- Add a drm_modeset_is_locked helper - the Grate Modset Locking Rework
will use the compiler to assist in the big reorg by renaming the
mode lock, so start encapsulating things. Unfortunately this ended
up in the "wrong" header file since it needs the definition of
struct drm_device.
v2: Drop most WARNS again - we hit them all over the place, mostly in
the setup and teardown sequences. And trying to fix it up leads to
nice deadlocks, since the locking in the setup code is really
inconsistent.
Reviewed-by: Rob Clark <rob@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is no longer used in the i915 code, so isolate it from the shared
struct.
This was originally part of:
commit 0e275518f325418d559c05327775bff894b237f7
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Mon Jan 14 13:35:33 2013 -0800
agp/intel: decouple more of the agp-i915 sharing
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
That commit had some other hunks which can't be used due to issues
Daniel found in previous commits.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: drop squash notice from the commit since it's imo ok to keep
this one separate.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The reasoning behind our code taking two paths depending upon whether or
not we may have been configured for IOMMU isn't clear to me. It should
always be safe to use the pci mapping functions as they are designed to
abstract the decision we were handling in i915.
Aside from simpler code, removing another member for the intel_gtt
struct is a nice motivation.
I ran this by Chris, and he wasn't concerned about the extra kzalloc,
and memory references vs. page_to_phys calculation in the case without
IOMMU.
v2: Update commit message
v3: Remove needs_dmar addition from Zhenyu upstream
This reverts (and then other stuff)
commit 20652097da
Author: Zhenyu Wang <zhenyuw@linux.intel.com>
Date: Thu Dec 13 23:47:47 2012 +0800
drm/i915: Fix missed needs_dmar setting
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> (v2)
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Squash in follow-up fix to remove the bogus hunk which
deleted the dma_mask configuration for gen6+.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And, move it to where the rest of the logic is.
There is some slight functionality changes. There was extra paranoid
checks in AGP code making sure we never do idle maps on gen2 parts. That
was not duplicated as the simple PCI id check should do the right thing.
v2: use IS_GEN5 && IS_MOBILE check instead. For now, this is the same as
IS_IRONLAKE_M but is more future proof. The workaround docs hint that
more than one platform may be effected, but we've never seen such a
platform in the wild. (Rodrigo, Daniel)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> (v1)
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_rgb_quant_range_selectable() will report whether the monitor
claims to support for RGB quantization range selection.
The information can be found in the CEA Video capability block.
v2: s/quantzation/quantization/ in the comment
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: David Airlie <airlied@linux.ie>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CONFIG_PM_SLEEP may be set even if CONFIG_ACPI_SLEEP is unset,
although that is unusual. For this reason, make the headers of
functions built for both CONFIG_ACPI and CONFIG_PM_SLEEP set
simultaneously depend on that combination of Kconfig options
instead of CONFIG_ACPI_SLEEP.
This fixes a build problem reported by Randy Dunlap.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move ACPI device power management functions from drivers/acpi/bus.c
to drivers/acpi/device_pm.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The only difference between acpi_bus_scan() and acpi_bus_add() is the
invocation of acpi_update_all_gpes() in the latter which in fact is
unnecessary, because acpi_update_all_gpes() has already been called
by acpi_scan_init() and the way it is implemented guarantees the next
invocations of it to do nothing.
For this reason, drop acpi_bus_add() and make all its callers use
acpi_bus_scan() directly instead of it. Additionally, rearrange the
code in acpi_scan_init() slightly to improve the visibility of the
acpi_update_all_gpes() call in there.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.
The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer. Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.
bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY. The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.
add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function old new delta
chr_dev_init 166 170 +4
allow_signal 80 82 +2
static.__warned 143 142 -1
disallow_signal 63 62 -1
__set_special_pids 95 94 -1
unregister_console 126 121 -5
start_kernel 546 541 -5
register_console 593 588 -5
copy_from_user 45 40 -5
sys_setsid 128 120 -8
sys_vhangup 32 19 -13
do_exit 1543 1526 -17
bitmap_zero 60 40 -20
arch_local_irq_save 137 117 -20
release_task 674 652 -22
static.spin_unlock_irqrestore 308 260 -48
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
no user of that should ever change that pointer,
so let's mark it const to prevent that from
happening.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull tty/serial fixes from Greg Kroah-Hartman:
"Here are a few tty/serial driver fixes for 3.8-rc4 that resolve a
number of problems that people have been having, including the ptys
ioctl issue that is a regression fix"
* tag 'tty-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
8250/16?50: Add support for Broadcom TruManage redirected serial port
pty: return EINVAL for TIOCGPTN for BSD ptys
serial:ifx6x60:Keep word size accordance with SPI controller
tty: 8250_dw: Fix inverted arguments to serial_out in IRQ handler
serial: samsung: remove redundant setting of line config during port reset
serial:ifx6x60:Delete SPI timer when shut down port
tty/8250: The correct device id for this card is 0x0022
tty/8250: pbn_b0_8_1152000_200 is supposed to be an 8 port definition
tty: serial: vt8500: fix return value check in vt8500_serial_probe()
serial: mxs-auart: Index is unsigned
mxs: uart: fix setting RTS from software
This function queries whether %current is an async worker executing an
async item. This will be used to implement warning on synchronous
request_module() from async workers.
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds default module loading and uses it to load the default
block elevator. During boot, it's called right after initramfs or
initrd is made available and right before control is passed to
userland. This ensures that as long as the modules are available in
the usual places in initramfs, initrd or the root filesystem, the
default modules are loaded as soon as possible.
This will replace the on-demand elevator module loading from elevator
init path.
v2: Fixed build breakage when !CONFIG_BLOCK. Reported by kbuild test
robot.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alex Riesen <raa.lkml@gmail.com>
Cc: Fengguang We <fengguang.wu@intel.com>
To be able to implement NS response offloading (in
regular operation or while in WoWLAN) drivers need
to know the IPv6 addresses assigned to interfaces.
Implement an IPv6 notifier in mac80211 to call the
driver when addresses change.
Unlike for IPv4, implement it as a callback rather
than as a list in the BSS configuration, that is
more flexible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on the driver, having ARP filtering for
some addresses may be possible. Remove the logic
that tracks whether ARP filter is enabled or not
and give the driver the total number of addresses
instead of the length of the list so it can make
its own decision.
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Because of rt->n removal, we do not need neigh argument any more.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 816422ad76 ("asm-generic, mm: pgtable: consolidate zero page
helpers") broke the compile on MIPS if SPARSEMEM is enabled. We get
this:
In file included from arch/mips/include/asm/pgtable.h:552,
from include/linux/mm.h:44,
from arch/mips/kernel/asm-offsets.c:14:
include/asm-generic/pgtable.h: In function 'my_zero_pfn':
include/asm-generic/pgtable.h:466: error: implicit declaration of function 'page_to_section'
In file included from arch/mips/kernel/asm-offsets.c:14:
include/linux/mm.h: At top level:
include/linux/mm.h:738: error: conflicting types for 'page_to_section'
include/asm-generic/pgtable.h:466: note: previous implicit declaration of 'page_to_section' was here
Due header files inter-dependencies, the only way I see to fix it is
convert my_zero_pfn() for __HAVE_COLOR_ZERO_PAGE to macros.
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: David Daney <david.daney@cavium.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This brings in all of the mei and other fixes that are needed to continue
development in this branch.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some pin configurations IP allows to set the current output to the pin.
This patch adds such a parameter to the pinconf-generic mechanism.
This parameter takes as argument the drive strength in mA.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver uses usb_phy interface to interact with s3c-hsotg. Supports
phy_init and phy_shutdown functions to enable/disable usb phy. Support
will be extended to host controllers and more Samsung SoCs.
Signed-off-by: Praveen Paneri <p.paneri@samsung.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are hardwares which support offload of data packets
for example when auto ARP is enabled the hw will send
the ARP response. In such cases if WEP encryption is
configured the hw must know the default WEP key in order
to encrypt the packets correctly.
When hw_accel is enabled and encryption type is set to WEP,
the driver should get the default key index from mac80211.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
[cleanups, fixes, documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The hci_request function is blocking and cannot be called through the
usual per-HCI device workqueue (hdev->workqueue). While hci_request is
in progress any other work from the queue, including sending HCI
commands to the controller would be blocked and eventually cause the
hci_request call to time out.
This patch adds a second workqueue to be used by operations needing
hci_request and thereby avoiding issues with blocking other workqueue
users.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This is to fix up a build problem with a wireless driver due to the
dynamic-debug patches in this branch.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A PCI-Express non-transparent bridge (NTB) is a point-to-point PCIe bus
connecting 2 systems, providing electrical isolation between the two subsystems.
A non-transparent bridge is functionally similar to a transparent bridge except
that both sides of the bridge have their own independent address domains. The
host on one side of the bridge will not have the visibility of the complete
memory or I/O space on the other side of the bridge. To communicate across the
non-transparent bridge, each NTB endpoint has one (or more) apertures exposed to
the local system. Writes to these apertures are mirrored to memory on the
remote system. Communications can also occur through the use of doorbell
registers that initiate interrupts to the alternate domain, and scratch-pad
registers accessible from both sides.
The NTB device driver is needed to configure these memory windows, doorbell, and
scratch-pad registers as well as use them in such a way as they can be turned
into a viable communication channel to the remote system. ntb_hw.[ch]
determines the usage model (NTB to NTB or NTB to Root Port) and abstracts away
the underlying hardware to provide access and a common interface to the doorbell
registers, scratch pads, and memory windows. These hardware interfaces are
exported so that other, non-mainlined kernel drivers can access these.
ntb_transport.[ch] also uses the exported interfaces in ntb_hw.[ch] to setup a
communication channel(s) and provide a reliable way of transferring data from
one side to the other, which it then exports so that "client" drivers can access
them. These client drivers are used to provide a standard kernel interface
(i.e., Ethernet device) to NTB, such that Linux can transfer data from one
system to the other in a standard way.
Signed-off-by: Jon Mason <jon.mason@intel.com>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For simple modules that contain a single platform_driver without any
additional setup code then ends up being a block of duplicated
boilerplate. This patch adds a new macro,
module_platform_driver_probe(), which replaces the
module_init()/module_exit() registrations with template functions.
This macro use the same idea of module_platform_driver().
This macro is useful to stop the misuse of module_platform_driver() for
removing the platform_driver_probe() boilerplate.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver supports the RocketPort EXPRESS and RocketPort INFINITY
families of PCI/PCIe multiport serial adapters. These adapters use a
"RocketPort 2" ASIC that is not compatible with the original RocketPort
driver (CONFIG_ROCKETPORT).
Tested with the RocketPort EXPRESS Octa DB9 and Quad DB9. Also added an
old RocketPort 8J PCI card to the same system to verify that rocket.c and
rp2.c coexist peacefully.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For RTF_GATEWAY route, return rt->rt6i_gateway.
Otherwise, return 2nd argument (destination address).
This will be used by following patches which remove rt->n
dependency patches in ip6_dst_lookup_tail() and ip6_finish_output2().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function, which looks up neighbour entry for an IPv6 address
without touching refcnt, will be used for patches to remove
dependency on rt->n (neighbour entry in rt6_info).
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to set/clear labels assigned to a conntrack
via ctnetlink.
To allow userspace to only alter specific bits, Pablo suggested to add
a new CTA_LABELS_MASK attribute:
The new set of active labels is then determined via
active = (active & ~mask) ^ changeset
i.e., the mask selects those bits in the existing set that should be
changed.
This follows the same method already used by MARK and CONNMARK targets.
Omitting CTA_LABELS_MASK is the same as setting all bits in CTA_LABELS_MASK
to 1: The existing set is replaced by the one from userspace.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Introduce CTA_LABELS attribute to send a bit-vector of currently active labels
to userspace.
Future patch will permit userspace to also set/delete active labels.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
similar to connmarks, except labels are bit-based; i.e.
all labels may be attached to a flow at the same time.
Up to 128 labels are supported. Supporting more labels
is possible, but requires increasing the ct offset delta
from u8 to u16 type due to increased extension sizes.
Mapping of bit-identifier to label name is done in userspace.
The extension is enabled at run-time once "-m connlabel" netfilter
rules are added.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The flags field of struct ceph_osd_req_op is never used, so just get
rid of it.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Both ceph_osdc_alloc_request() and ceph_osdc_build_request() are
provided an array of ceph osd request operations. Rather than just
passing the number of operations in the array, the caller is
required append an additional zeroed operation structure to signal
the end of the array.
All callers know the number of operations at the time these
functions are called, so drop the silly zero entry and supply that
number directly. As a result, get_num_ops() is no longer needed.
This also means that ceph_osdc_alloc_request() never uses its ops
argument, so that can be dropped.
Also rbd_create_rw_ops() no longer needs to add one to reserve room
for the additional op.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Only one of the two callers of ceph_osdc_alloc_request() provides
page or bio data for its payload. And essentially all that function
was doing with those arguments was assigning them to fields in the
osd request structure.
Simplify ceph_osdc_alloc_request() by having the caller take care of
making those assignments
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Add support for the UART device present in Broadcom TruManage capable
NetXtreme chips (ie: 5761m 5762, and 5725).
This implementation has a hidden transmit FIFO, so running in single-byte
interrupt mode results in too many interrupts. The UART_CAP_HFIFO
capability was added to track this. It continues to reload the THR as long
as the THRE and TSRE bits are set in the LSR up to a specified limit (1024
is used here).
Signed-off-by: Stephen Hurd <shurd@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only thing ceph_osdc_alloc_request() really does with the
flags value it is passed is assign it to the newly-created
osd request structure. Do that in the caller instead.
Both callers subsequently call ceph_osdc_build_request(), so have
that function (instead of ceph_osdc_alloc_request()) issue a warning
if a request comes through with neither the read nor write flags set.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
