Pinnacle class devices should return "88 07 xx" or "88 08 xx" when
entering command mode. If either the first byte or the second byte is
invalid, return an error.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Dave Turvene <dturvene@dahetral.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The official ALPS driver uses the EC report, not the E7 report, to detect
these devices. Also, they check for a range of values; the original
table-based code only checked for two specific ones.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Dave Turvene <dturvene@dahetral.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This allows alps_identify() to override these settings based on the
device characteristics, if it is ever necessary.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Dave Turvene <dturvene@dahetral.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In anticipation of adding more ALPS protocols and more per-device quirks,
use function pointers instead of switch statements to call functions that
differ from one device to the next.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Dave Turvene <dturvene@dahetral.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If the E6 report test passes, get the E7 and EC reports right away and
then try to match an entry in the table.
Pass in the alps_data struct, so that the detection code will be able to
set operating parameters based on information found during detection.
Change the version (psmouse->model) to report the protocol version only,
in preparation for supporting models that do not show up in the ID table.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Dave Turvene <dturvene@dahetral.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Several ALPS driver init sequences repeat a command three times, then
issue PSMOUSE_CMD_GETINFO to read the result. Move this into a helper
function to simplify the code.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Dave Turvene <dturvene@dahetral.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This will minimize the number of forward declarations needed when
alps_get_model() starts assigning function pointers.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Dave Turvene <dturvene@dahetral.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Not every type of ALPS touchpad is well-suited to table-based detection.
Start moving the various alps_model_data attributes into the alps_data
struct so that we don't need a unique table entry for every possible
permutation of protocol version, flags, byte0/mask0, etc.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Dave Turvene <dturvene@dahetral.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Adjust the gpio-em.c driver to reconsider the pdata->irq_base
variable. Non-DT board code like for instance board-kzm9d.c
needs to operate of a static IRQ range for platform devices.
So this patch is updating the code to make use of the function
irq_domain_add_simple() instead of irq_domain_add_linear().
Fixes a EMEV2 / KZM9D runtime error caused by the following commit:
7385500 gpio/em: convert to linear IRQ domain
Cc: stable@kernel.org
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Reported-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some mmio devices have a dedicated interface clock that needs
to be enabled to access their registers. This patch optionally
enables a clock before accessing registers in the regmap_bus
callbacks.
I added (devm_)regmap_init_mmio_clk variants of the init
functions that have an added clk_id string parameter. This
is passed to clk_get to request the clock from the clk
framework.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
commit dd8004af: 'regulator: core: Log when a device causes a voltage
constraint fail', tried to print out some information about the
check consumer min/max uV fixup, however, it uses a garbage pointer
left over from list_for_each_entry leading to boot messages in the
form:
'[ 2.079890] <RANDOM ASCII>: Restricting voltage, 3735899821-4294967295uV'
Because it references regulator->dev, it could potentially read memory from
anywhere causing a panic.
This patch instead uses rdev and the updated min/max uV values.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Paul writes:
Please pull the following to get the removal of the original IBM PC-XT
hard disk driver from the block layer (drivers/block/xd.c).
As near as I can tell, it hasn't seen a run time fix in over a dozen
years, and with drive sizes of 10-20MB, and performance of about 128kB/s
maximum, it is no surprise that it has been completely unused for well
over a decade.
The removal was originally posted[1] well over a month ago, and since
then, there has been nobody objecting to the removal, aside from someone
who had mistakenly confused it with a completely different driver (hd.c)
The VIA VX855/VX875 GPIO and RDC R-321x GPIO support drivers select
MFD_CORE which itself depends on GENERIC_HARDIRQ support.
So add this dependency to these two drivers as well to prevent
selection of MFD_CORE.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When removing the !S390 dependency from drivers/input/Kconfig a couple
of drivers don't compile because they have a dependency on GENERIC_HARDIRQS.
So add the missing dependencies.
Fixes e.g. this one:
drivers/input/keyboard/lm8323.c: In function ‘lm8323_suspend’:
drivers/input/keyboard/lm8323.c:801:2: error: implicit declaration of function ‘irq_set_irq_wake’
[-Werror=implicit-function-declaration]
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The s390 architecture is unique in respect to dirty page detection,
it uses the change bit in the per-page storage key to track page
modifications. All other architectures track dirty bits by means
of page table entries. This property of s390 has caused numerous
problems in the past, e.g. see git commit ef5d437f71
"mm: fix XFS oops due to dirty pages without buffers on s390".
To avoid future issues in regard to per-page dirty bits convert
s390 to a fault based software dirty bit detection mechanism. All
user page table entries which are marked as clean will be hardware
read-only, even if the pte is supposed to be writable. A write by
the user process will trigger a protection fault which will cause
the user pte to be marked as dirty and the hardware read-only bit
is removed.
With this change the dirty bit in the storage key is irrelevant
for Linux as a host, but the storage key is still required for
KVM guests. The effect is that page_test_and_clear_dirty and the
related code can be removed. The referenced bit in the storage
key is still used by the page_test_and_clear_young primitive to
provide page age information.
For page cache pages of mappings with mapping_cap_account_dirty
there will not be any change in behavior as the dirty bit tracking
already uses read-only ptes to control the amount of dirty pages.
Only for swap cache pages and pages of mappings without
mapping_cap_account_dirty there can be additional protection faults.
To avoid an excessive number of additional faults the mk_pte
primitive checks for PageDirty if the pgprot value allows for writes
and pre-dirties the pte. That avoids all additional faults for
tmpfs and shmem pages until these pages are added to the swap cache.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Texas Instruments WL1273 I2C FM Radio (RADIO_WL1273) selects
MFD_CORE, which itself depends on GENERIC_HARDIRQS.
So add the dependency to the TI driver as well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The AT91RM9200 driver call devm_request_irq() and therefore should
depend on GENERIC_HARDIRQS to prevent link/compile errors on plaforms
without GENERIC_HARDIRQS.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When the DASD devices are detached from the driver, then the
dasd_generic_remove function is called. One of the things this
function should do is to remove the DASD specific sysfs attributes,
but this is not done in all cases. This is likely to cause an oops
when at a later point sysfs stumbles over the stale pointers. In
particular this happens when when the modules are unloaded and loaded
again.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Loading the pci hotplug module when no devices are present will fail
but unfortunately some hotplug callbacks stay registered to the pci
bus level. Fix this by not letting module loading fail when no pci
devices are present and provide proper {de}registration functions
for these callbacks.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
pci_probe is too generic and has a name clash with other common code parts.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix name clash with some common code device drivers and add "tod"
to all tod clock access function names.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Convert the defines for the !CONFIG_SCM* stuff to static inline
functions.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When an attempt to query or modify the grouping state of a channel path
fails due to a timeout, we cannot be sure about its state. To get back to
a defined state, disband the whole path group and try again while excluding
the offending path.
Reviewed-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add new attribute "vpm" to the subchannel sysfs directory of I/O
subchannels. This attribute contains a path mask indicating which
channel paths were successfully verified to be usable for I/O.
Reviewed-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Omit known to be broken paths (those set in path_noirq_mask) for the
sense/set PGID and nop IO commands.
Note: path_noirq_mask will be reset in ccw_device_verify_start (the
paths could be healthy again). However if we restart a path
verification via verify_start this mask will not be reset (there is
no need to let the wait for an interrupt time out again - plus we
do not want to loop once we deal with the paths in unknown path group
state).
Reviewed-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do not abort path verification when waiting for an interrupt timed out.
Use path_noirq_mask to keep track of the paths used for this (also
maintain a path_notoper_mask for debugging purposes). If the timeout
happend to be during an operation where we query or alter the state of
path groups set the pgid_unknown flag.
With this change we allow usage of devices which have such ill-behaved
paths (if at least one path is operational).
Reviewed-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Under LPAR the zfcpdump HSA is a shared resource. Up to now the HSA memory
is released when the zcore file is closed. Dump programs that know that
they do not need the HSA memory any more (e.g. because they already dumped it)
could release it earlier. This would allow other LPARs to use it again.
To achieve this a new debugfs file "hsa" is added that can be used to read
the HSA size and to release the HSA by writing "0" into the file.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Convert the synchronous size sense code to an interrupt driven
approach. This allows to set the device online even if the
terminal is not connected. With the new code views can be
registered without a connected terminal, the tty can be opened
as soon as the device is online. After the terminal has been
connected and the size has been determined the tty is resized
to match the device characteristics..
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a notifier to create / destroy the device nodes for the tty view
and the fullscreen view. Only device nodes for online devices are
created and the device names will follow the convention as outlined
in Documentation/devices.txt: 3270/tty<x> for the tty nodes,
3270/tub<x> for hte fullscreen nodes and 3270/tub for the fullscreen
control node.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Corrects the order of tasklet_init vs. the allocation of the
read request which has been broken by git commit 9d2ae233
"TTY: tty3270, move initialization to allocation".
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reintroduce the tty3270_open function which has been removed by
git commit 20cda6f2 "TTY: tty3270, add tty install". Without
the open function in the tty_operations tty_open will return
-ENODEV and the 3270 tty will not work.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch registers the pl330 dma controller driver with the generic
device tree dma helper functions.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add xlate to translate the device-tree binding information into
the appropriate format. The filter function requires the dma
controller device and dma channel number as filter_params.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds a new pl330_dt_filter for DT case to filter the
required channel based on the new filter params and modifies the
old filter only for non-DT case as suggested by Arnd Bergmann.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
