Sparse complains that we use zero instead of NULL here. In fact, the
initialization is wrong and should be removed. Doing these kinds of
bogus initializations means that GCC can't detect unitialized variables
and leads to bugs.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As of now the ANI cycle is executed only when the chip is awake.
On idle state case, the station wakes up from network sleep for
beacon reception. Since most of the time, ANI cycle is not syncing
with beacon wakeup, ANI cycle is ignored. Approx 5 mins once, the
calibration is performed. This could affect the connection stability
when the station is idle for long. Even though the OFDM and CCK phy
error rates are too high, ANI is unable to tune its immunity level
as quick enough due to rare execution.
Here the experiment shows that OFDM and CCK levels are at default
even on higher phy error rate.
listenTime=44 OFDM:3 errs=121977/s CCK:2 errs=440818/s ofdm_turn=1
This change ensures that ANI calibration will be exectued atleast
once for every 10 seconds. The below result shows improvements and
immunity levels are adopted quick enough.
listenTime=557 OFDM:4 errs=752/s CCK:4 errs=125/s ofdm_turn=0
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes the way the driver deals with
command responses and traps which are sent through
the special interrupt input endpoint 3.
While the carl9170 firmware does not use this
endpoint for command responses or traps, the
firmware loader on the device does. It uses it
to notify the host about 'watchdog triggered'
in case the firmware/hardware has crashed.
Note:
Even without this patch, the driver is still
able to detect the mishap and reset the device.
But previously it did that because the trap
event caused an out-of-order message sequence
number error, which also triggered a reset.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DBG_CMD_NUM is the number of commands, not the actual bytes of
data for printing.
Also remove the duplicated DBG_CMD_NUM definition.
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some rt2800 devices don't have their calibrated max eirp tx power in
their calibration data. For those devices reduce tx power according to
difference between regulatory max channel power and requested tx power.
This patch is based on Helmut Schaa work.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don use TX_PWR_CFG_0 register value of OFDM 6M tx power as criterion
since it can be changed. The same do vendor driver (see
AsicAdjustSingleSkuTxPower and AsicGetTxPowerOffset functions from
2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO).
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We skip compensate calculation for non 11b rates on 2.4GHz band. I do
not see that on vendor driver
(2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO).
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on AsicAdjustTxPower function from vendor driver
(2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO)
limit per rate TX power values we program into TX_PWR_CFG_ registers.
Note that on some configurations (devices/rates) is allowed to use
bigger values than 0xc, but we use safe maximum value for now. Further
work need to be done to allow use bigger values than 0xc.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX power delta can be negative. TX_PWR_CFG_ registers allow to set delta
only in range between 0 dBm and 15 dBm (4 bits for each rate). Se we
need to use BBP_R1 to configure negative deltas.
Not utilize +6 dBm increasing BBP_R1 option for safety reason. For now,
this can be used for devices, which export maximum allowed TX power
value.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All defines for REG_WRITE in Atheros wireless drivers use the order "ah",
"register" and "value". hw.c is the only file using the order "ah", "value" and
"register".
drivers/net/wireless/ath/ath9k/hw.h:#define REG_WRITE(_ah, _reg, _val) \
drivers/net/wireless/ath/key.c:#define REG_WRITE(_ah, _reg, _val) (common->ops->write)(_ah, _val, _reg)
This inconsistent definition can easily lead to implementation errors. The
modification doesn't change the behavior of the driver or the generated code.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch changes a bit trace output format in the rtl_cam_program_entry() to
print prefix and the actual data on the same line. Moreover the %*phC outputs
each byte as 2 hex digits, which is slightly different to the original %x.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
ACKed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ezusb_read_ltv() we had a comparison "(bufsize < 0)" which was never
true because bufsize was unsigned. I looked at the implications of
that. If we passed a negative number to ezusb_access_ltv() then it
would be used as the size parameter of the memcpy() because that
function uses min_t(int, exp_len, ans_size).
But fortunately when I looked at the callers, bufsize is not controlled
by the user and it's never negative. So these signedness mistakes have
no impact.
I removed the always false check from ezusb_read_ltv() and I changed the
types in ezusb_access_ltv() and made the variables unsigned.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch remove a semicolon after if(...) that is preventing the
error check to work correctly. Removing this semicolon will change the
code behavior, but this is intended.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r1@
position p;
@@
if (...);@p
@script:python@
p0 << r1.p;
@@
// Emacs org-mode output
cocci.print_main("", p0)
cocci.print_secs("", p0)
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BT_OP_SCAN is applicable only for pre-MCI WLAN/BT combo chips
and using it for MCI-based cards is incorrect. Fix this by
cleaning up its usage.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BCM4706 has two PCIe host controller on the bcma bus. For PCIe
client mode it is assumed that there is only one PCIe controller so the
PCIe driver, like b43 and brcmsmac are accessing the first PCIe
controller when they want to issue a operation on the host controller.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch does two things:
* Use macb struct members and remove at91_ether ones
* Alloc DMA buffers on netdev start and dealloc on stop
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
This rips out the at91_ether phy handling and ethtool stuff
and replace it with equivalent stuff from macb.
The only thing lost is the phy irq support from at91_ether,
but this can be added to macb and then benefit all users.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
This will make it easier to share code between the drivers and
eventually merge them into one driver.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Use register and bits definitions from the macb header. This makes it
possible to have one header file for this hardware.
Process was scripted and the resulting object file has the same checksum.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
This change makes it so that igb_update_dca is broken into two halves, one
for Rx and one for Tx. The advantage to this is primarily readability.
In addition I am enabling relaxed ordering for reads from hardware since
this is supported on all of the igb parts.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change helps to address locking issues seen with
netif_set_real_num_tx_queues and netif_set_real_num_rx_queues when used in
the igb_set_interrupt_capability function. To resolve these locking issues
I have moved the two function calls into __igb_open so that they can be
called while the RTNL lock is held.
An added advantage to this is that the number of queues is not updated
until the last possible moment so if there are any issues in allocating
MSI-X interrupts or resources for the rings we have time to change the
values prior to updating the netdev.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change combines the the allocation of q_vectors and rings into a single
function. The advantage of this is that we are guaranteed we will avoid
overlap in the L1 cache sets.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change locks us in at 2K buffers even on a system that supports larger
frames. The reason for this change is to make better use of pages and to
reduce the overall truesize of frames generated by igb.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to try and isolate things a bit further I am moving the code
related to retrieving data from the rx_buffer_info structure into a
separate function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we map the entire page and just sync half of
it for the device at a time. The advantage to this approach is that we can
avoid the locking on map/unmap seen in many IOMMU implementations.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to just clean-up a number of function calls that were
made at the end of the Rx clean-up path by combining them into a single
function call.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we no longer use header split. The idea is to
reduce partial cache line writes by hardware when handling frames larger
then header size. We can compensate for the extra overhead of having to
memcpy the header buffer by avoiding the cache misses seen by leaving an
full skb allocated and sitting on the ring.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to support page based receive we will need to split up the two
different types of timestamping into two separate functions. The first one
will handle legacy timestamps with the value in the register, and the new
one will handle timestamps in the Rx buffer itself.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Current implementation mess up the tail pointer. This patch sets skb->tail
correctly.
Also, the small packet check and padding is optimized by using unlikely and
calling skb_pad directly.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change allows us to add a mailbox versioning API. This will allow us
to determine the features supported by the VFs from the PF. For example we
will be implementing a version 1.1 API for the VF that will indicate that
it can support us enabling Jumbo frames as the VF will support buffer
chaining.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Robert Garrett <RobertX.Garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of trying to maintain one large monolithic function that handles
most of the different messages from the VF it makes sense to break the
message handling function up so that we can just go through one switch
statement and call the correct routine for a given message.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can have limited support for jumbo frames
when SR-IOV is enabled. In order to accomplish this it is necessary to
disable all VFs when the PF has jumbo frames enabled. If the VFs then
request the same maximum frame size as the PF they will be re-enabled. A
follow on patch will add a means of identifying when a VF can support
spanning buffers and does not need to be worried about the actual supported
max frame size.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Tested-by: Robert Garrett <robertx.e.garrett@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When enabling DCB the rings belonging to a q_vector on CPU 0 were not
reinitializing their DCA registers. Upon closer inspection the issue was
that the q_vector CPU variable was left at 0 resulting in the driver not
updating the DCA registers.
In order to guarantee the DCA registers will be updated I am adding a
couple line change so that we initialize the CPU variable to -1 which will
force a DCA update the first time an interrupt fires on that q_vector.
In addition we were setting the CPU affinity hint to all CPUs when we were
not specifying a CPU. Instead we should leave it as all zeros to avoid any
possible confusion about the fact that we shouldn't be giving a hint.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This driver add support for wake over lan on AT803x phys.
Signed-off-by: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
