With the introduction of new AB* platforms, it's important to allow
as much code reuse as possible. By allowing a system's number of IRQs
to be dynamically passed, we can reuse almost all of the -debugfs
driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
In case of AB-V3, the eye diagram related issues are resolved.
So, set the device charging current to 300mA when connected to
standard host. Also, add the USB PHY tuning values to improve
the USB eye diagram
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: <thirupathi.chippakurthy@stericsson.com>
Add debugfs entry ab8500/hwreg to read/write bit-field in AB8500 registers.
Check the debugfs entries usage from heading comments in ab8500-debugfs.c
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: carriere etienne <etienne.carriere@stericsson.com>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Partly for coding style reasons, but mostly because sparse warns on it.
This patch is a completion of a previous patch by Mark Brown.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some drivers can detect subsystem failures e.g. shared memory driver
can detect modem sub system failures. It would be helpful in analyzing
these failures if AB register dump is available at that point. This
patch adds the API for the drivers to dump AB registers in the kernel
log.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Reviewed-by: Linus WALLEIJ <linus.walleij@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
The resolution of msleep is related to HZ, so with HZ set to
100 any msleep of less than 10ms will become ~10ms.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It's possible to supply a string to provide a reason for
triggering a restart. In this case our reason is to enter
charging-only mode, as a charger was found to be present.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
When a charger is connected, we usually want AB8500 based systems to
reboot into charging-only mode. However, if the battery type cannot
be identified this would be futile, so we'll just shut the system
down instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
The kernel allows us to specify a function call-back which will be
invoked when a system power-off request has been received. Here we
provide one which is to be used when shutting down AB8500 based
platforms.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
From Pawel Moll:
Versatile Express related driver updates for 3.9:
* Move sp810 header to a more generic location,
mainly to share it with arm64
* tag 'vexpress/drivers-for-3.9' of git://git.linaro.org/people/pawelmoll/linux:
arm: Move sp810.h to include/linux/amba/
+ Linux 3.8-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
From Linus Walleij:
Removal of the <mach/id.h> include from ux500
- First an ACKed MFD patch deleting the only consumer
of these cpu_is* functions outside of mach-ux500
- Introduce a new local cpu_is_u8580() in this patch
set to avoid clashing with other patch sets.
- Finally de-globalize <mach/id.h>.
* tag 'ux500-no-idh' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: de-globalize <mach/id.h>
ARM: ux500: Introduce cpu_is_u8580()
mfd: prcmu: delete pin control helpers
Signed-off-by: Olof Johansson <olof@lixom.net>
This removes the file <mach/id.h> from the global kernel include
scope, making it a pure mach-ux500 detail. All ASIC specifics
needed by drivers shall henceforth be passed from either platform
data or the device tree.
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch 52666298a 'mfd: vexpress-sysreg: Don't skip initialization
on probe' adds a call to vexpress_sysreg_setup from a non-__init
function, so this also has to lose its __init annotation.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: arm@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
* depends/cleanup: (375 commits)
ARM: at91: fix board-rm9200-dt after sys_timer conversion
clocksource: use clockevents_config_and_register() where possible
ARM: use clockevents_config_and_register() where possible
clockevents: export clockevents_config_and_register for module use
timer: vt8500: Move timer code to drivers/clocksource
irqchip: Move ARM vic.h to include/linux/irqchip/arm-vic.h
ARM: picoxcell: use common irqchip_init function
ARM: spear: use common irqchip_init function
irqchip: Move ARM VIC to drivers/irqchip
ARM: samsung: remove unused tick.h
ARM: remove unneeded vic.h includes
ARM: remove mach .handle_irq for VIC users
ARM: VIC: set handle_arch_irq in VIC initialization
ARM: VIC: shrink down vic.h
irqchip: Move ARM gic.h to include/linux/irqchip/arm-gic.h
ARM: use common irqchip_init for GIC init
irqchip: Move ARM GIC to drivers/irqchip
ARM: remove mach .handle_irq for GIC users
ARM: GIC: set handle_arch_irq in GIC initialization
ARM: GIC: remove direct use of gic_raise_softirq
...
Pull MFD fixes from Samuel Ortiz:
"This is the first pull request for MFD fixes for 3.8
We have some build failure fixes (twl4030, vexpress, abx500 and
tps65910), some actual runtime oops and lockup fixes (rtsx, da9052),
and some more hypothetical NULL pointers dereferences fixes for
pcf50633 and max776xx.
Then we also have additional rtsx fixes for a correct switch output
voltage and clock divider correctness for rtl8411 (rtsx driver), and
irqdomain fix for db8550-prcmu, and some more cosmetic fixes for
arizona and wm5102."
* tag 'mfd-for-linus-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: rtsx: Fix oops when rtsx_pci_sdmmc is not probed
mfd: wm5102: Fix definition of WM5102_MAX_REGISTER
mfd: twl4030: Don't warn about uninitialized return code
mfd: da9052/53 lockup fix
mfd: rtsx: Add clock divider hook
mmc: rtsx: Call MFD hook to switch output voltage
mfd: rtsx: Add output voltage switch hook
mfd: Fix compile errors and warnings when !CONFIG_AB8500_BM
mfd: vexpress: Export global functions to fix build error
mfd: arizona: Check errors from regcache_sync()
mfd: tc3589x: Use simple irqdomain
mfd: pcf50633: Init pcf->dev before using it
mfd: max77693: Init max77693->dev before using it
mfd: max77686: Init max77686->dev before using it
mfd: db8500-prcmu: Fix irqdomain usage
mfd: tps65910: Select REGMAP_IRQ in Kconfig to fix build error
mfd: arizona: Disable control interface reporting for WM5102 and WM5110
If rtsx_pci_sdmmc is not probed, function pointer pcr->slots[].card_event
will point to NULL, and thus rtsx_pci_card_detect will reference a NULL
pointer.
Check card_event pointer before referencing it can avoid kernel panic.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If the twl4030_write_script function gets called with
a zero length argument, its return value does not
get set. We know that all scripts have a nonzero
length, but returning an error in case they ever
do is probably appropriate.
Without this patch, building omap2plus_defconfig results in:
drivers/mfd/twl4030-power.c: In function 'load_twl4030_script':
drivers/mfd/twl4030-power.c:414:5: error: 'err' may be used uninitialized in this function
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: "Kristo, Tero" <t-kristo@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
An issue has been reported where the PMIC either locks up or fails to
respond following a system Reset. This could result in a second write
in which the bus writes the current content of the write buffer to address
of the last I2C access.
The failure case is where this unwanted write transfers incorrect data to
a critical register.
This patch fixes this issue to by following any read or write with a dummy read
to a safe register address. A safe register address is one where the contents
will not affect the operation of the system.
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add callback function conv_clk_and_div_n to convert between SSC clock
and its divider N.
For rtl8411, the formula to calculate SSC clock divider N is different
with the other card reader models.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Different card reader has different method to switch output voltage,
add this callback to let the card reader implement its individual switch
function.
This is needed as rtl8411 has a specific switch output voltage procedure.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vexpress-sysreg driver does not have to be initialized
early, when the platform doesn't require this. Unfortunately
in such case it wasn't initialized correctly - master site
lookup and config bridge registration were missing. Fixed now.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
If charging is started before USB enumeration of an Accessory
Charger Adapter has finished, the AB8500 will generate a
VBUS_ERROR. This in turn results in timeouts and delays the
enumeration with around 15 seconds. This patch delays the
charging and then ramps currents slowly to avoid VBUS errors.
The delay allows the enumeration to have finished before
charging is turned on.
Signed-off-by: Martin Sjoblom <martin.w.sjoblom@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
drivers/mfd/ab8500-core.c:1015:21: error: ‘ab8500_bm_data’ undeclared here
include/linux/mfd/abx500/ab8500-bm.h:445:13: warning: ‘ab8500_fg_reinit’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:448:13: warning: ‘ab8500_charger_usb_state_changed’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:451:29: warning: ‘ab8500_btemp_get’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:455:12: warning: ‘ab8500_btemp_get_batctrl_temp’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:463:12: warning: ‘ab8500_fg_inst_curr_blocking’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:442:12: warning: ‘ab8500_fg_inst_curr_done’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:447:26: warning: ‘ab8500_fg_get’ defined but not used
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Compiling vexpress client drivers as module results in error messages such as
ERROR: "__vexpress_config_func_get" [drivers/hwmon/vexpress.ko] undefined!
ERROR: "vexpress_config_func_put" [drivers/hwmon/vexpress.ko] undefined!
This is because the global functions in drivers/mfd/vexpress-config.c are not
exported. Fix it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If the control bus is unrelabile we may hit errors during regcache_sync(),
especially given that it tends to be one the most dense bursts of I/O in
many systems.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes a regression in the TC3589x driver introduced in
commit 15e27b1088
"mfd: Provide the tc3589x with its own IRQ domain"
If a system with a TC3589x expander is booted and a base
IRQ is passed from platform data, a legacy domain will
be used. However, since the Ux500 is now switched to use
SPARSE_IRQ, no descriptors get allocated on-the-fly,
and we get a crash.
Fix this by switching to using the simple irqdomain that
will handle this uniformly and also allocates descriptors
explicitly.
Also fix two small whitespace errors in the vicinity while
we're at it.
Cc: stable@kernel.org
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Current code uses pcf->dev in the dev_err call before setting it to
&client->dev. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Current code uses max77693->dev in the dev_err call before setting it to
&i2c->dev. Fix it.
This patch also includes below cleanups:
- Move checking pdata earlier and show dev_err if no platform data found.
- Remove unnecessary err_regmap goto label.
- Unregister i2c devices if regmap init for muic fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Current code uses max77686->dev in the dev_err call before setting it to
&i2c->dev. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes two issues with the DB8500 PRCMU irqdomain:
- You have to state the irq base 0 to get a linear domain
for the DT case from irq_domain_add_simple()
- The irqdomain was not used to translate the initial irq
request using irq_create_mapping() making the linear
case fail as it was lacking a proper descriptor.
I took this opportunity to fix two lines of whitespace
errors in related code as I was anyway messing around with
it.
Cc: stable@kernel.org
Acked-by Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TPS65910 mfd driver uses functions that are only avaiable when
REGMAP_IRQ is enabled. So "select REGMAP_IRQ" is added to mfd
Kconfig to fix below build error:
drivers/built-in.o: In function `tps65910_irq_exit':
/media/anil/kernel/drivers/mfd/tps65910.c:265: undefined reference to `regmap_del_irq_chip'
drivers/built-in.o: In function `tps65910_irq_init':
/media/anil/kernel/drivers/mfd/tps65910.c:254: undefined reference to `regmap_add_irq_chip'
drivers/built-in.o: In function `tps65910_i2c_probe':
/media/anil/kernel/drivers/mfd/tps65910.c:509: undefined reference to `regmap_irq_get_domain'
make: *** [vmlinux] Error 1
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Tested-by: Matt Porter <mporter@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This brings in all of the mei and other fixes that are needed to continue
development in this branch.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the build error:
drivers/built-in.o: In function `twl_probe':
drivers/mfd/twl-core.c:1256: undefined reference to `devm_regmap_init_i2c'
make: *** [vmlinux] Error 1
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[ Samuel is busy, taking it directly - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
