CRT is the first output which can be cloned, hence we cannot (yet)
move the dpms handling over to disable/enable. This requires some more
smarts in intel_crtc_dpms first to set the display pipe status
depening upon encoder->connectors_active of all connected encoders.
Because that will happen in a separate step, don't touch the dpms
functions, yet.
v2: Be careful about clearing the _DISABLE flags for intermediate dpms
modes - otherwise we might clobber the crt state when another (cloned)
connector gets enabled.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DP is the first encoder which isn't simple. As
commit d240f20f54
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Fri Aug 13 15:43:26 2010 -0700
drm/i915: make sure eDP PLL is enabled at the right time
discovered, we need to enable the eDP PLL for the cpu port _before_ we
enable the pipes and planes. After a few more commits the current
solution is to enable the PLL in the dp mode_set function (because
this is the only encoder callback the crtc helper code calls before it
calls the crtc's commit function).
Now I suspect that we actually should enable/disable the entire cpu
eDP port before/after planes, but thanks to how the crtc helper code
assumes that you can disable an encoder without disabling it's crtc
right away, this won't work.
The result is that the current prepare/commit hooks don't touch the
eDP PLL, but instead it get's frobbed in dp_mode_set and in the dp
dpms function. Hence we need to keep things (at least for now)
bug-for-bug compatible by using our own special dp dpms function and
keep everything else more-or-less as-is (just using our own
infrastrucutre now).
This mess can only be cleaned up once we control the entire modeset
sequence and can move things around freely.
v2: Squash unsupported dpms modes to OFF at the beginning of the DP
dpms function.
v3: Need to set the dpms state to off in dp_disable, otherwise this
breaks the newly added WARNs ...
v4: Rebased against edp panel off sequence changes in 3.6-rc2
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like hdmi tv outputs are simple: They only have 2 states and can't be
cloned. Hence give it the same treatment.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've picked hdmi as the first encoder to convert because it's rather
simple:
- no cloning possible
- no differences between prepare/commit and dpms off/on switching.
A few changes are required to do so:
- Split up the dpms code into an enable/disable function and wire it
up with the intel encoder.
- Noop out the existing encoder prepare/commit functions used by the
crtc helper - our crtc enable/disable code now calls back into the
encoder enable/disable code at the right spot.
- Create new helper functions to handle dpms changes.
- Add intel_encoder->connectors_active to better track dpms state. Atm
this is unused, but it will be useful to correctly disable the
entire display pipe for cloned configurations. Also note that for
now this is only useful in the dpms code - thanks to the crtc
helper's dpms confusion across a modeset operation we can't (yet)
rely on this having a sensible value in all circumstances.
- Rip out the encoder helper dpms callback, if this is still getting
called somewhere we have a bug. The slight issue with that is that
the crtc helper abuses dpms off to disable unused functions. Hence
we also need to implement a default encoder disable function to do
just that with the new encoder->disable callback.
- Note that we drop the cpt modeset verification in the commit
callback, too. The right place to do this would be in the crtc's
enable function, _after_ all the encoders are set up. But because
not all encoders are converted yet, we can't do that. Hence disable
this check temporarily as a minor concession to bisectability.
v2: Squash the dpms mode to only the supported values -
connector->dpms is for internal tracking only, we can hence avoid
needless state-changes a bit whithout causing harm.
v3: Apply bikeshed to disable|enable_ddi, suggested by Paulo Zanoni.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just prep work, not yet put to some use.
Note that because we're still using the crtc helper to switch modes
(and their complicated way to do partial modesets), we need to call
the encoder's disable function unconditionally.
But once this is cleaned up we shouldn't call the encoder's disable
function unconditionally any more, because then we know that we'll
only call it if the encoder is actually enabled. Also note that we
then need to be careful about which crtc we're filtering the encoder
list on: We want to filter on the crtc of the _current_ mode, not the
one we're about to set up.
For the enabling side we need to do the same trick. And again, we
should be able to simplify this quite a bit when things have settled
into place.
Also note that this simply does not take cloning into account, so dpms
needs to be handled specially for the few outputs where we even bother
with it.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just impendance matching with the the crtc helper stuff.
... and somehow the design of this all ended up in this commit here,
too ;-)
The big plan is that this new set of crtc display_funcs take full
responsibility of modeset operations for the entire display output
pipeline (by calling down into object-specific callbacks and
functions). The platform-specific callbacks simply know best what the
proper order is.
This has the drawback that we can't do minimal change-overs any more
if a modeset just disables one encoder in a cloned configuration
(because we will only expose a disable/enable action that takes
down/sets up the entire crtc including all encoders). Imo that's the
only sane way to do it though:
- The use-case for this is pretty minimal, even when presenting (at
least sane people) should use a dual-screen output so that you can
see your notes on your panel. Clone mode is imo BS.
- With all the clone mode constrains, shared resources, and special
ordering requirements (which differ even on the same platform
sometimes for different outputs) there's no way we'd get this right
for all cases. Especially since this is a under-used feature.
- And to top it off: On haswell even dp link re-training requires us
to take down the entire display pipe - otherwise the chip dies.
So the only sane way is to do a full modeset on every crtc where the
output config changes in any way.
To support global modeset (i.e. set the configuration for all crtcs at
once) we'd then add one more function to allocate global and shared
objects in the best ways (e.g. fdi links, pch plls, ...). The crtc
functions would then simply use the pre-allocated stuff (and shouldn't
be able to fail, ever). We could even do all the object pinning in
there (and maybe try to defragment the global gtt if we fail)!
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because that's what we're essentially calling. This is the first step
in untangling the crtc_helper induced dpms handling mess we have - at
the crtc level we only have 2 states and the magic is just in
selecting which one (and atm there isn't even much magic, but on
recent platforms where not even the crt output has more than 2 states
we could do better).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The original patch was actually incorrect in stubbing out the sysfs for
l3 parity.
commit 5ab3633d69
Author: Hunt Xu <mhuntxu@gmail.com>
Date: Sun Jul 1 03:45:07 2012 +0000
drm/i915: make rc6 in sysfs functions conditional
Unfortunately Hunt didn't respond to my review comments, and Daniel
sucked in the patch again ignoring. Worst of all, I'm too lazy to write
the patch for what I originally wanted, which was to keep rc6 sysfs even
without CONFIG_PM. This simpler patch does enough to enable us to add
more sysfs entries though.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Most of the DRM drivers appear to be missing the .compat_ioctl file
operation entry necessary for 32-bit application compatibility.
This patch uses drm_compat_ioctl for all drivers which don't have
their own, and which are using drm_ioctl for .unlocked_ioctl.
This leaves drivers/gpu/drm/psb/psb_drv.c unchanged; it has a custom
.unlocked_ioctl and will presumably need a custom .compat_ioctl as
well.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
In drivers/usb/Kconfig "config USB_ARCH_HAS_HCD" is within "if USB_SUPPORT"
statement.
In drivers/gpu/drm/Kconfig "config DRM_USB" depends on USB_ARCH_HAS_HCD
but selects USB_SUPPORT which leads to the error for udl Kconfig:
$ yes "" | make oldconfig
scripts/kconfig/conf --oldconfig Kconfig
drivers/gpu/drm/udl/Kconfig:1:error: recursive dependency detected!
drivers/gpu/drm/udl/Kconfig:1: symbol DRM_UDL depends on USB_ARCH_HAS_HCD
drivers/usb/Kconfig:76: symbol USB_ARCH_HAS_HCD depends on USB_SUPPORT
drivers/usb/Kconfig:58: symbol USB_SUPPORT is selected by DRM_USB
drivers/gpu/drm/Kconfig:22: symbol DRM_USB is selected by DRM_UDL
Fix this by changing from select to depends on USB_SUPPORT in
"config DRM_USB".
This is a follow-up fix to df0b344300
in Dave's drm-next GIT branch.
[ v2: Restore old status, but change from select to depends on USB_SUPPORT ]
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Previously intel_panel_setup_backlight() would create a sysfs backlight
interface with max brightness of 1 if it was unable to figure out the max
backlight brightness. This rendered the backlight interface useless.
Do not create a dysfunctional backlight interface to begin with.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: David Woodhouse <David.Woodhouse@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The same designer from the previous patch has told us to never read
FORCEWAKE. We only do this for the POSTING_READ(), so simply change that
to something within the same cacheline (for no reason in particular
other than it sounds nice). In the _mt case we can leverage
the gtfifodbg check for the POSTING_READ.
This partially reverts
commit 6af2d180f8
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jul 26 16:24:50 2012 +0200
drm/i915: fix forcewake related hangs on snb
v2: commit message, comments about posting read from (Daniel)
Note: vlv forcewake doesn't need any changes for this special
treatment since FORCEWAKE_VLV is in a totally different register
range, and the readback FORCEWAKE_ACK_VLV readback that follows is in
the same range.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Added note.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A designer familiar with the hardware has stated that the forcewake
timeout can theoretically be as high as a little over 1ms. Therefore we
modify our code to use 2ms (appropriate fudge and because we don't want
to round down).
Hopefully this can't prevent spurious timeouts.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Acked-by: Chris Wilson <chris@chris-wilson.oc.uk>
[danvet: again fix conflict with vlv patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As part of the advice given to us from the hardware designers regarding
the maximum wait time on the forcewake handshake we need to move from us
granularity to ms granularity. In earlier patches to do this, Jani
noticed that wait_for_us was properly converted to use cpu_relax(), but
wait_for was not.
The issue has existed since the introduction of the macro:
commit 913d8d1100
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sat Aug 7 11:01:35 2010 +0100
drm/i915: Ensure that while(INREG()) are bounded (v2)
CC: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.oc.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's used all over the place, and we want to be able to play around with
the value, apparently. Note that it doesn't touch other timeouts of the
same value (like gtfifo, and thread C0 wait).
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.oc.uk>
[danvet: fixup conflict with vlv forcewake patches.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The sdvo hotplug support check and activation has worked by coincidence for
TMDS0. The boolean value returned by intel_sdvo_supports_hotplug() was
masked with a bit shifted by device number, which also should have been one
of SDVO_OUTPUT_* bits instead. Boolean true masked with 1 shifted by 0 just
happened to match SDVO_OUTPUT_TMDS0...
Get hotplug support as a bit mask, check the correct bits for support, and
use the correct bits for activating hotplug support.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Simon Farnsworth <simon.farnsworth@onelan.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Avoid constant wakeups caused by noisy irq lines when we don't even care
about the irq. This should be particularly useful for i945g/gm where the
hotplug has been disabled:
commit 768b107e4b
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri May 4 11:29:56 2012 +0200
drm/i915: disable sdvo hotplug on i945g/gm
v2: While at it, remove the bogus hotplug_active read, and do not mask
hotplug_active[0] before checking whether the irq is needed, per discussion
with Daniel on IRC.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=38442
Tested-by: Dominik Köppl <dominik@devwork.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
<ickle> danvet: in the force wake, both DRM_ERRORs have the same string.
<ickle> useful for .txt shrinkage, horrible for debugging
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For some odd reasons, the vlv forcewake code is rather different from
all other platforms, with no clear justification. Adjust things:
- Don't check whether the gt is awake already (and bail out early), we
need to grab a forcewake anyway. Otherwise the chip might go to
sleep too early. And this would also screw up our forcewake
accounting.
- Like all other platforms, check whether the gt has cleared the
forcewake bit in the _ACK register before setting it again.
- Use _MASKED_BIT_ENABLE/DISABLE macros
- Only use bit0 of the forcewake reg, not all 16 bits.
- check the gtfifodb reg like on all other platforms in _put.
- Drop the POSTING_READs for consistency.
v2: Failure to git add ... again.
v3: Fixup the spelling fail a bit.
Tested-by: "Purushothaman, Vijay A" <vijay.a.purushothaman@intel.com>
Tested-by: "Widawsky, Benjamin" <benjamin.widawsky@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We've had and still have too many issues where the gpu turbo doesn't
quite to what it's supposed to do (or what we want it to do).
Adding a tracepoint to track when the desired gpu frequency changes
should help a lot in characterizing and understanding problematic
workloads.
Also, this should be fairly interesting for power tuning (and
especially noticing when the gpu is stuck in high frequencies, as has
happened in the past) and hence for integration into powertop and
similar tools.
Cc: Arjan van de Ven <arjan@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like with the equivalent change for gen6+ rps state, this helps in
clarifying the code (and in fixing a few places that have fallen through
the cracks in the locking review).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From Bspec, Vol 2a, Section 1.9.3.4 "PIPE_CONTROL", intro section
detailing the various workarounds:
"[DevIVB {W/A}, DevHSW {W/A}]: Pipe_control with CS-stall bit
set must be issued before a pipe-control command that has the State
Cache Invalidate bit set."
Note that public Bspec has different numbering, it's Vol2Part1,
Section 1.10.4.1 "PIPE_CONTROL" there.
There's also a second workaround for the PIPE_CONTROL command itself:
"[DevIVB, DevVLV, DevHSW] {WA}: Every 4th PIPE_CONTROL command, not
counting the PIPE_CONTROL with only read-cache-invalidate bit(s) set,
must have a CS_STALL bit set"
For simplicity we simply set the CS_STALL bit on every pipe_control on
gen7+
Note that this massively helps on some hsw machines, together with the
following patch to unconditionally set the CS_STALL bit on every
pipe_control it prevents a gpu hang every few seconds.
This is a regression that has been introduced in the pipe_control
cleanup:
commit 6c6cf5aa9c
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Jul 20 18:02:28 2012 +0100
drm/i915: Only apply the SNB pipe control w/a to gen6
It looks like the massive snb pipe_control workaround also papered
over any issues on ivb and hsw.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: squashed both workarounds together, pimped commit message
with Bsepc citations, regression commit citation and changed the
comment in the code a bit to clarify that we unconditionally set
CS_STALL to avoid being hurt by trying to be clever.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For now, just a copy of gen6_render_ring_flush. Different gens have
different workarounds, so we want different functions.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Avoid constant wakeups caused by noisy irq lines when we don't even care
about the irq. This should be particularly useful for i945g/gm where the
hotplug has been disabled:
commit 768b107e4b
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri May 4 11:29:56 2012 +0200
drm/i915: disable sdvo hotplug on i945g/gm
v2: While at it, remove the bogus hotplug_active read, and do not mask
hotplug_active[0] before checking whether the irq is needed, per discussion
with Daniel on IRC.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=38442
Tested-by: Dominik Köppl <dominik@devwork.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In order to setup the i2c channel, we power up the panel
via ironlake_edp_panel_vdd_on, however it requires
intel_dp->panel_power_up_delay to be initialised,
which hasn't been setup yet.
So move things around so we set the panel power up
values first then init the i2c stuff.
This is one step to fixing the eDP panel in the MBP
from uninitialised state.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
"New stuff for -next. Highlights:
- prep patches for the modeset rework. Note that one of those patches
touches the fb helper in the common drm code.
- hasw hdmi audio support (Wang Xingchao)
- improved instdone dumping for gen7 (Ben)
- unbound tracking and a few follow-up patches from Chris
- dma_buf->begin/end_cpu_access plus fix for drm/udl (Dave)
- improve mmio error reporting for hsw
- prep patch for WQ_NON_REENTRANT removal (Tejun Heo)
"
* 'for-airlied' of git://people.freedesktop.org/~danvet/drm-intel: (41 commits)
drm/i915: Remove __GFP_NO_KSWAPD
drm/i915: disable rc6 on ilk when vt-d is enabled
drm/i915: Avoid unbinding due to an interrupted pin_and_fence during execbuffer
drm/i915: Use new INSTDONE registers (Gen7+)
drm/i915: Add new INSTDONE registers
drm/i915: Extract reading INSTDONE
drm/i915: Use a non-blocking wait for set-to-domain ioctl
drm/i915: Juggle code order to ease flow of the next patch
drm/i915: Use cpu relocations if the object is in the GTT but not mappable
drm/i915: Extract general object init routine
drm/i915: Protect private gem objects from truncate (such as imported dmabuf)
drm/i915: Only pwrite through the GTT if there is space in the aperture
i915: use alloc_ordered_workqueue() instead of explicit UNBOUND w/ max_active = 1
drm/i915: Find unclaimed MMIO writes.
drm/i915: Add ERR_INT to gen7 error state
drm/i915: Cantiga+ cannot handle a hsync front porch of 0
drm/i915: fix reassignment of variable "intel_dp->DP"
drm/i915: Try harder to allocate an mmap_offset
drm/i915: Show pin count in debugfs
drm/i915: Show (count, size) of purgeable objects in i915_gem_objects
...
These two fix the MacBook Pro 2012 Retina display.
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/nouveau/linux-2.6:
drm/nv50-/gpio: initialise to vbios defaults during init
drm/nvd0/disp: hopefully fix selection of 6/8bpc mode on DP outputs
This is required to fix an issue on the Retina MBP where the eDP panel's
AUX channel isn't wired up to the HPD pin for the panel, causing our aux
code to bail out early.
From looking at various traces of the binary driver, it appears NVIDIA do
something very similar on at least all nv50+ chipsets during their
initialisation sequence. So, hopefully this is safe.
Issue and fix initially tracked down by Ryan Bourgeois on fdo#51971.
Backported fix from reworked nouveau kernel module.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
I have a very limited number of traces available for DP on NVD9+, but,
these values produce the same as the binary driver on a confirmed 18-bit
eDP panel and a confirmed 24-bit eDP panel (Retina MBP).
It's interesting that the bitfield values also match the MODE_CTRL values
that control the same thing on nv50:nvd9.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Alex writes:
Highlights:
- fix a gart regression on older IGP chips
- more MSAA fixes
- fix a double free in gpu reset code
- modesetting fixes
- trinity dig encoder fix.
* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix dig encoder selection on DCE61
drm/radeon: fix double free in radeon_gpu_reset
drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
drm/radeon: rework panel mode setup
drm/radeon/atom: powergating fixes for DCE6
drm/radeon/atom: rework DIG modesetting on DCE3+
drm/radeon: don't disable plls that are in use by other crtcs
drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
drm/radeon: initialize tracked CS state
drm/radeon: fix reading CB_COLORn_MASK from the CS
[this one ideally should make 3.6 - it fixes the very annoying mode setting bug]
This causes the pipe to be forced off prior to initial mode set, which
roughly mirrors the behavior of the i915 driver. It fixes initial mode
setting on my Intel DN2800MT (Cedarview) board. Without it, mode
setting triggers an out-of-range error from the monitor for most modes,
but only on initial configuration (i.e. they can be configured
successfully from userspace after that).
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
radeon_ring_restore is freeing the memory for the saved
ring data. We need to remember that, otherwise we try to
restore the ring data again on the next try. Additional
to that it shouldn't try the reset infinitely if we have
saved ring data.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Adjust the panel mode setup to match the behavior
of the vbios. Rather than checking for specific
bridge chip ids, just check the eDP configuration register.
This saves extra aux transactions and works across
DP bridge chips without requiring additional per chip
id checking.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Power gating is per crtc pair, but the powergating registers
should be called individually. The hw handles power up/down
properly. The pair is powered up if either crtc in the pair
is powered up and the pair is not powered down until both
crtcs in the pair are powered down. This simplifies
programming and should save additional power as the previous
code never actually power gated the crtc pair.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The ordering is important and the current drm code
wasn't cutting it for modern DIG encoders. We need
to have information about crtc before setting up
the encoders so I've shifted the ordering a bit.
Probably we'll need a full rework akin to danvet's
recent intel patchs. This patch fixes numerous
issues with DP bridge chips and makes link training
much more reliable.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Checking of the second colorbuffer was skipped on r700, because
CB_TARGET_MASK was 0xf. With r600, CB_TARGET_MASK is changed to 0xff,
so we must set the number of samples of the second colorbuffer to 1 in order
to pass the CS checker.
The DRM version is bumped, because RESOLVE_BOX is always rejected without this
fix on r600.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This should help catch uninitialized registers and reject commands
because of that.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Daniel writes:
"Just a few smaller things:
- Fix up a pipe vs. plane confusion from a refactoring, fixes a regression
from 3.1 (Anhua Xu).
- Fix ivb sprite pixel formats (Vijay).
- Fixup ppgtt pde placement for machines where the Bios artifically limits
the availbale gtt space in the name of ... product differentiation
(Chris). This fixes an oops.
- Yet another no_lvds quirk entry."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
drm/i915: Use the correct size of the GTT for placing the per-process entries
drm/i915: fix color order for BGR formats on IVB
drm/i915: fix wrong order of parameters in port checking functions
Ben says its just a single fix to avoid the wrong pcopy units being used.
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nvc0/copy: check PUNITS to determine which copy engines are disabled
On some Fermi chipsets (NVCE particularly) PCOPY1 doesn't exist. And if
what I've seen on Kepler is true of Fermi too, chipsets of the same type
can have different PCOPY units available.
This should fix a v3.5 regression reported by a number of people effecting
suspend/resume on NVC8/NVCE chipsets.
Cc: stable@vger.kernel.org [3.5]
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
