Add I2C0 device tree and pin muxing information to da850-evm.
Also, add OF_DEV_AUXDATA for I2C0 controller driver in da850
board dt file to use I2C0 clock.
Verified i2c0 node gets created in sys class interface as
"/sys/class/i2c-dev/i2c-0/subsystem/i2c-0".
nsekhar@ti.com: tested using i2cdetect and i2cdump.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Since AM33XX supports only DT-boot, this is needed
for the appropriate device nodes to be created.
Note: OCMC RAM is part of the PER power domain and supports
retention. The assembly code for low power entry/exit will
run from OCMC RAM. To ensure that the OMAP PM code does not
attempt to disable the clock to OCMC RAM as part of the
suspend process add the no_idle_on_suspend flag.
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
From Tony Lindgren:
Minimal updates to OMAP board-*.c files while converting
things to device tree based booting.
* tag 'omap-for-v3.9/board-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap2plus_defconfig: enable omap1 rtc
RX-51: Register twl4030-madc device
RX-51: Add leds lp5523 names from Maemo 5 2.6.28 kernel
ARM: OMAP2+: AM33XX: omap2plus_defconfig: Add support for few drivers
ARM: OMAP1: nokia770: enable CBUS/Retu
ARM: OMAP2+: omap2plus_defconfig: enable CMA allocator
ARM: OMAP2+: omap2plus_defconfig: enable TFP410 chip support
ARM: OMAP3: igep0020: simplify GPIO LEDs dependencies
ARM: OMAP2+: craneboard: support the TPS65910 PMU
ARM: OMAP2+: craneboard: support NAND device
ARM: OMAP3: cm-t3517: add MMC support
ARM: OMAP2+: Remove apollon board support
+ Linux 3.8-rc6
Signed-off-by: Olof Johansson <olof@lixom.net>
From Stephen Warren:
ARM: tegra: device tree updates
Numerous updates to the various Tegra device trees are made:
* Addition of NVIDIA Beaver (Tegra30) and Toradex Colibri T20 and Iris
carrier boards.
* Enablement of the HDMI connector on most boards.
* Enablement of the keyboard controller on a few boards.
* Addition of the AC'97 controller to Tegra20.
* Addition of a GPIO poweroff node for TrimSlice.
* Changes to support the new "high speed UART" (DMA-capable) driver for
Tegra serial ports, and enablement for Cardhu's UART C.
* A few cleanups, such as compatible flag fixes, node renames, node
ordering fixes, commonizing properties into SoC .dtsi files, etc..
This pull request is based on (most of) the previous pull request with
tag tegra-for-3.9-soc-t114.
* tag 'tegra-for-3.9-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (22 commits)
ARM: dt: tegra30: Rename "smmu" to "iommu"
ARM: dt: tegra20: Rename "gart" to "iommu"
ARM: tegra: move serial clock-frequency attr into the Tegra30 dtsi
ARM: tegra: Add Toradex Iris carrier board DT with T20 512MB COM
ARM: tegra: Add Colibri T20 512MB COM device tree
ARM: tegra: move serial clock-frequency attr into the Tegra20 dtsi
ARM: tegra: harmony: enable keyboard in DT
ARM: tegra: whistler: enable keyboard in DT
ARM: tegra: cardhu: register UARTC
ARM: tegra: seaboard: enable keyboard in DT
ARM: tegra: add DT entry for KBC controller
ARM: tegra: swap cache-/interrupt-ctrlr nodes in DT
ASoC: tegra: add ac97 host controller to device tree
ARM: DT: tegra: Add Tegra30 Beaver board support
ARM: DT: tegra: Add board level compatible properties
ARM: tegra: paz00: enable HDMI port
ARM: tegra: ventana: enable HDMI port
ARM: tegra: seaboard: enable HDMI port
ARM: tegra: trimslice: add gpio-poweroff node to DT
ARM: DT: tegra: Unify the description of Tegra20 boards
...
From Stepen Warren:
ARM: tegra: add Tegra114 SoC support
This pull request adds initial support for the Tegra114 SoC, which
integrates a quad-core ARM Cortex-A15 CPU. I'm proud to observe that we
posted the initial versions of these patches before the final official
announcement of this chip.
These patches are enough to boot with a UART-based console, support the
Dalmore and Pluto reference/evaluation boards, instantiate the GPIO and
pinctrl drivers, and enable a cpuidle state. As yet, no clocks or
storage devices are supported, but patches for those will follow shortly.
This pull request is based on (most of) the previous pull request with
tag tegra-for-3.9-soc-cpuidle, followed by a merge of the previous pull
request with tag tegra-for-3.9-scu-base-rework.
* tag 'tegra-for-3.9-soc-t114' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (24 commits)
ARM: DT: tegra114: add pinmux DT entry
ARM: DT: tegra114: add GPIO DT entry
ARM: tegra114: select PINCTRL for Tegra114 SoC
ARM: tegra: add Tegra114 ARM_CPUIDLE_WFI_STATE support
ARM: tegra: Add SMMU entry to Tegra114 DT
ARM: tegra: add AHB entry to Tegra114 DT
ARM: tegra: Add initial support for Tegra114 SoC.
ARM: dt: tegra114: Add new board, Pluto
ARM: dt: tegra114: Add new board, Dalmore
ARM: dt: tegra114: Add new SoC base, Tegra114 SoC
ARM: tegra: fuse: Add chip ID Tegra114 0x35
ARM: OMAP: Make use of available scu_a9_get_base() interface
ARM: tegra: Skip scu_enable(scu_base) if not Cortex A9
ARM: Add API to detect SCU base address from CP15
ARM: tegra: Use DT /cpu node to detect number of CPU core
ARM: tegra: Add CPU nodes to Tegra30 device tree
ARM: tegra: Add CPU nodes to Tegra20 device tree
ARM: perf: simplify __hw_perf_event_init err handling
ARM: perf: remove unnecessary checks for idx < 0
ARM: perf: handle armpmu_register failing
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Remove/add conflict in arch/arm/mach-tegra/common.c resolved.
Remove/remove conflict in arch/arm/mach-tegra/platsmp.c. Leave the empty
stub function for now since removing it in the merge commit is confusing;
will be cleaned up in a separate commit. # # It looks like you may be
committing a merge. # If this is not correct, please remove the file #
.git/MERGE_HEAD # and try again.
From Stephen Warren:
ARM: tegra: USB driver cleanup
The Tegra USB driver has a number of issues:
1) The PHY driver isn't a true platform device, and doesn't implement
the standard USB PHY API.
2) struct device instance numbers were used to make decisions in the
driver, rather than being parameterized by DT or platform data.
This pull request solves issue (2), and lays the groundwork for solving
issue (1). The work on issue (1) involved introducing new DT nodes for
the USB PHYs, which in turn interacted with the Tegra common clock
framework changes, due to the move of clock lookups into device tree.
Hence, these USB driver changes are taken through the Tegra tree with
acks from USB maintainers.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-soc-ccf.
* tag 'tegra-for-3.9-soc-usb' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
usb: host: tegra: make use of PHY pointer of HCD
ARM: tegra: Add reset GPIO information to PHY DT node
usb: host: tegra: don't touch EMC clock
usb: add APIs to access host registers from Tegra PHY
USB: PHY: tegra: Get rid of instance number to differentiate PHY type
USB: PHY: tegra: get rid of instance number to differentiate legacy controller
ARM: tegra: add clocks properties to USB PHY nodes
ARM: tegra: add DT nodes for Tegra USB PHY
usb: phy: remove unused APIs from Tegra PHY.
usb: host: tegra: Resetting PORT0 based on information received via DT.
ARM: tegra: Add new DT property to USB node.
usb: phy: use kzalloc to allocate struct tegra_usb_phy
ARM: tegra: remove USB address related macros from iomap.h
From Stephen Warren:
ARM: tegra: Common Clock Framework rework
Tegra already supports the common clock framework, but had issues:
1) The clock driver was located in arch/arm/mach-tegra/ rather than
drivers/clk/.
2) A single "Tegra clock" type was implemented, rather than separate
clock types for PLL, mux, divider, ... type in HW.
3) Clock lookups by device drivers were still driven by device name
and connection ID, rather than through device tree.
This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.
* tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (31 commits)
clk: tegra30: remove unused TEGRA_CLK_DUPLICATE()s
clk: tegra20: remove unused TEGRA_CLK_DUPLICATE()s
ARM: tegra30: remove auxdata
ARM: tegra20: remove auxdata
ASoC: tegra: remove auxdata
staging: nvec: remove use of clk_get_sys
ARM: tegra: paz00: add clock information to DT
ARM: tegra: add clock properties to Tegra30 DT
ARM: tegra: add clock properties to Tegra20 DT
spi: tegra: do not use clock name to get clock
ARM: tegra: remove legacy clock code
ARM: tegra: migrate to new clock code
clk: tegra: add clock support for Tegra30
clk: tegra: add clock support for Tegra20
clk: tegra: add Tegra specific clocks
ARM: tegra: define Tegra30 CAR binding
ARM: tegra: define Tegra20 CAR binding
ARM: tegra: move tegra_cpu_car.h to linux/clk/tegra.h
ARM: tegra: add function to read chipid
ARM: tegra: fix compile error when disable CPU_IDLE
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
arch/arm/mach-tegra/common.c
arch/arm/mach-tegra/platsmp.c
drivers/clocksource/Makefile
From Shawn Guo:
imx fixes for 3.8, take 4
- It fixes fec ptp clock pointer in device tree source.
* tag 'imx-fixes-3.8-4' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx6: fix fec ptp clock slow 10 time
Fix the use of USART on both at91sam9x5 and at91sam9n12. In DTS, the
atmel,use-dma-[rx|tx] property is present but a DMA channel cannot be used.
Indeed the connexion between the DMA engine and the slave is not implemented
yet in Device Tree.
Note however that this property is also used for PDC (private DMA) on older
SoCs. This is why the driver alone cannot determine the validity of this
property.
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org> [3.8+]
ptp should use enet_ref instead of pll6_enet
pll6_enet is fixed 500Mhz.
There are divider between enet_ref and pll6_enet
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
From Jason Cooper:
mvebu drivers for v3.9
- use rtc-mv in mvebu armv7 SoCs
- add pci-e hotplug for kirkwood
Depends on:
- tags/mvebu_fixes_for_v3.8-rc6
* tag 'drivers_for_v3.9' of git://git.infradead.org/users/jcooper/linux:
cpuidle: kirkwood: Move out of mach directory
rtc: Add support of rtc-mv for MVEBU SoCs
ARM: Kirkwood: Support basic hotplug for PCI-E
arm: mvebu: i2c come back in defconfig
arm: plat-orion: fix printing of "MPP config unavailable on this hardware"
Dove: activate GPIO interrupts in DT
Cubieboard has two LEDs available for use, a blue one (labeled LED1)
and a green one (labeled LED2).
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Highbank processors depend on the external ECME to perform voltage
management based on a requested frequency. Communication between the
A9 cores and the ECME happens over the pl320 IPC channel.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
From Simon Horman:
Second round of Renesas ARM-based SoC changes for v3.9
* Changes to allow unplugging of CPU0 by Ulrich Hecht.
* Changes to add reg and device_type properties to cpus
device trees entries by Simon Horman.
* tag 'renesas-soc2-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: mach-shmobile: sh73a0: allow unplugging of CPU0
ARM: mach-shmobile: add shmobile_cpu_disable_any()
ARM: mach-shmobile: emev2: Add reg and device_type properties to cpus
ARM: mach-shmobile: sh73a0: Add reg and device_type properties to cpus
Signed-off-by: Olof Johansson <olof@lixom.net>
fixes for v3.8-rc6
- add missing gpio interrupt lines to dove dt
- fix bad logic for printing MPP error message on orion boards
- build proper serial port driver after changing mvebu DT compatible property
- This is a change to mvebu_defconfig that I wouldn't usually push out as a
fix. However, the commit
b24212f arm: mvebu: Use dw-apb-uart instead of ns16650 as UART driver
changed the serial driver for the board in the dts file. without the patch
I've included in this pull, users won't see any log messages.
fixes for v3.8-rc6
- add missing gpio interrupt lines to dove dt
- fix bad logic for printing MPP error message on orion boards
- build proper serial port driver after changing mvebu DT compatible property
- This is a change to mvebu_defconfig that I wouldn't usually push out as a
fix. However, the commit
b24212f arm: mvebu: Use dw-apb-uart instead of ns16650 as UART driver
changed the serial driver for the board in the dts file. without the patch
I've included in this pull, users won't see any log messages.
From Nicolas Ferre:
Two little Device Tree fixes for USART on at91sam9x5.
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91/at91sam9x5.dtsi: fix usart3 TXD
ARM: at91: at91sam9x5: fix usart3 pinctrl name
The renaming of pinctrl_uart3 to pinctrl_usart3 was missed in
commit 9e3129e (ARM: at91: fix usart/uart namimg in pinctrl).
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
From Jason Cooper:
fixes for v3.8-rc6
- add missing gpio interrupt lines to dove dt
- fix bad logic for printing MPP error message on orion boards
- build proper serial port driver after changing mvebu DT compatible property
- This is a change to mvebu_defconfig that I wouldn't usually push out as a
fix. However, the commit
b24212f arm: mvebu: Use dw-apb-uart instead of ns16650 as UART driver
changed the serial driver for the board in the dts file. without the patch
I've included in this pull, users won't see any log messages.
* tag 'mvebu_fixes_for_v3.8-rc6' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: i2c come back in defconfig
arm: plat-orion: fix printing of "MPP config unavailable on this hardware"
Dove: activate GPIO interrupts in DT
As the wdt nodes have the gic as their interrupt-parent, their
interrupts property should be 3 cells in format described in the gic
devicetree binding document.
This patch fixes the interrupts property in the wdt nodes to be in the
correct format.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Tegra114 has the GPIO controllers with 8 GPIO bank and each bank
supports 32 pins.
Add DT entry for GPIO controller. Tegra114 GPIO controller is
compatible with Tegra30 GPIO controller driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Use functional name for DT entry instead of h/w name.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Use functional name for DT entry instead of h/w name.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
From Stephen Warren:
ARM: bcm2835: device tree updates
The SoC's SDHCI and MMC controllers are added to device tree, and enabled
in the Raspberry Pi board device tree. Some fixed clocks are added to the
device tree to support these drivers. These could be replaced by real
clocks in the future.
A hard-coded memreserve is removed from device tree; the bootloader should
specify the correct memory node content instead, since the memory layout
is dynamic.
This branch is based on v3.8-rc3.
* tag 'bcm2835-for-3.9-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi:
ARM: bcm2835: fix clock node aliasing in device tree
ARM: bcm2835: add I2C controllers to DT
ARM: bcm2835: add SDHCI node to DT
ARM: bcm2835 rpi: remove hard-coded memreserve from DT
Signed-off-by: Olof Johansson <olof@lixom.net>
From Linus Walleij:
Nomadik Device Tree conversion rebased on ARM SoC cleanup branch
This patch set converts the Nomadik (mach-nomadik) to
Device Tree and delete the old board files, paving the
road for single zImage.
* tag 'nmk-dt-on-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: get rid of <mach/hardware.h>
ARM: nomadik: delete old board files
ARM: nomadik: add I2C devices to the device tree
ARM: nomadik: migrate MMC/SD card support to device tree
ARM: nomadik: convert SMSC91x ethernet to device tree
ARM: nomadik: move GPIO and pinctrl to device tree
ARM: nomadik: add FSMC NAND
ARM: nomadik: move remaining PrimeCells to device tree
ARM: nomadik: move pin maps to cpu file
ARM: nomadik: initial devicetree support
ARM: nomadik: move last custom calls to pinctrl
Signed-off-by: Olof Johansson <olof@lixom.net>
From Simon Horman, a series of SoC updates for shmobile.
* 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7779: scif .irqs used SCIx_IRQ_MUXED()
ARM: mach-shmobile: sh73a0: Initialise MMCIF using DT
ARM: mach-shmobile: sh73a0: Minimal setup using DT
ARM: mach-shmobile: sh73a0: Allow initialisation of GIC by DT
ARM: SH-Mobile: sh73a0: Add CPU Hotplug
ARM: SH-Mobile: sh73a0: Secondary CPUs handle own SCU flags
ARM: shmobile: r8a7740: Add CPU sleep suspend
ARM: shmobile: sh73a0: Add CPU sleep suspend
ARM: shmobile: add function declarations for sh7372 DT helper functions
ARM: sh7372: fix cache clean / invalidate order
ARM: sh7372: add clock lookup entries for DT-based devices
ARM: mach-shmobile: sh73a0 external IRQ wake update
ARM: shmobile: sh73a0: fixup div4_clks bitmap
ARM: shmobile: r8a7740: add TMU timer support
ARM: shmobile: Remove duplicate inclusion of dma-mapping.h in setup-r8a7740.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix trivial conflict in board_bcm due to Simon resolving the same conflict
with one less line of whitespace. Keeping end result common with what
we already have in arm-soc.
Conflicts:
arch/arm/mach-bcm/board_bcm.c
From Simon Horman, updates to a few shmobile boards.
* 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Include sh73a0 DTSI in kzm9g
ARM: shmobile: Include DTSI of r8a7740 to armadillo800eva
ARM: shmobile: kzm9g: Use of_machine_is_compatible()
ARM: shmobile: add sample amixer settings for armadillo800eva
ARM: shmobile: add sample amixer settings for ap4evb
ARM: shmobile: fix sample amixer settings for mackerel
ARM: mackerel: include the correct .dtsi file
Signed-off-by: Olof Johansson <olof@lixom.net>
The DAC found on the last chip select requires a word length of 12 bits,
which is not supported by the SSP controller of the iMX28. Use
bitbanging for that bus to support such a length.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch removes custom way of adding spi dma channels and
adds according to new generic DMA DT bindings.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
