The Linksys WRT1900AC (Mamba) is a router that has
- 2 mini-PCIe slots with Marvell 88W8864 radios
- 1 USB 3.0 port
- 1 USB 2.0/eSATAp port
- 2 Ethernet interfaces connected to a 88E6172 switch (1x WAN + 4x LAN)
- 128MB NAND flash
- 256MB RAM
gregory.clement@free-electrons.com: - add ARM to the title
- fix the reference to CONFIG_DEBUG_MVEBU_UART0_ALTERNATE
- fix the unbalanced comment for the syscfg partition
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds reset-gpios property to the eMMC slot, so the MMC driver
is able to properly reset eMMC card on system restart and thus fixes
system hang on software reboot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds reset-gpios property to the eMMC slot, so the MMC driver
is able to properly reset eMMC card on system restart and thus fixes
system hang on software reboot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Enabling SDIO IRQ signalling for the wifi MMC/SDIO slot
doubles the transmission transfer rate.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Snow board has a MMC/SDIO wifi chip that is always powered but it
needs a power sequence involving a reset (active low) and an enable
(active high) pins. Both pins are marked as active low since the MMC
simple power sequence driver asserts the pins prior to the card power
up procedure and de-asserts the pins after the card has been powered.
So the reset line will be left de-asserted and the enable pin will be
left asserted.
The chip also needs an external 32kHz reference clock to be operational
that is by the MAX77686 PMIC clock.
Add a simple MMC power sequence provider for the wifi MMC/SDIO slot.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add a device node for the System Controller, with subnodes that
represent the hardware power area hierarchy.
Hook up all devices to their respective PM domains.
Add a minimal device node for the Coresight-ETM hardware block, and
hook it up to the D4 PM domain, so the R-Mobile System Controller
driver can keep the domain powered, until the new Coresight code
handles runtime PM.
The System Controller is also used by the R-Mobile Reset driver, which
can now restart the system.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
In commit 87517d26d8 ("ARM: dts: dra7-evm: Add extcon nodes for USB")
we enabled Extcon USB gpio to tackle the USB ID pin and get
peripheral mode to work.
But the extcon-gpio-usb driver [1] didn't make it into v4.0
and this makes the USB driver defer probe indefinitely breaking
USB Host functionality.
As a temporary fix we remove the extcon handle from the
USB controller and add it back when the extcon driver
merges in v4.1.
[1] - https://lkml.org/lkml/2015/2/2/187
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
we have i2c0 sleep pinctrl state but were passing
default state anyhow. Fix that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As it turns out, tps62362 is actually on I2C bus0,
not bus1. This has gone unnoticed because Linux
doesn't use (as of now) that regulator at all, it's
setup by the bootloader and left as is.
While at that, also add missing reg property for
our regulator.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Offset for smc91x must be zero otherwise smc91x linux kernel driver does not
detect smc91x ethernet hardware in qemu N900 machine.
The 0x300 offset was used to supress a warning the smsc911x
driver produces about non-standard offset as 0x300 seems to
be the EEPROM default. As only three address lines are
connected both 0 and 0x300 will work just fine with 0 being
correct. The warning about the non-standard offset can be
fixed by writing to EEPROM as that's needed in any case to
set the MAC address.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
[tony@atomide.com: updated comments, just use 0 instead of 0x0]
Signed-off-by: Tony Lindgren <tony@atomide.com>
With legacy boot i2c buses on Nokia N900 are numbered i2c1, i2c2 and i2c3.
Commit 20b80942ef ("ARM: dts: OMAP3+: Add i2c aliases") fixed the
numbering with DT boot, but introduced a regression on N900 - aliases
become i2c0, i2c1 and i2c2. Fix that by providing the correct aliases in
the board dts.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: this is needed for legacy user space to work]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 7800064ba5 ("ARM: dts: Add basic dm816x device tree
configuration") added basic devices for dm816x, but I was not able
to test the USB completely because of an unconfigured USB phy, and
I only tested it to make sure the Mentor chips are detected and
clocked without a phy.
After testing the USB with actual devices I noticed a few issues
that should be fixed to avoid confusion:
- The USB id pin on dm8168-evm is hardwired and can be changed
only by software. As there are two USB-A type connectors, let's
start both in host mode instead of otg.
- The Mentor core is configured in such a way on dm8168-evm that
it's not capable of multipoint at least on revision c board
that I have.
- We need ranges for the syscon to properly set up the phy as
children of the SCM syscon area.
- Let's not disable the second interface, the board specific
dts files can do that if really needed. Most boards should
just keep it enabled to ensure the device is idled properly.
Note that also a phy and several musb fixes are still needed to
make the USB to work properly in addition to this fix.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sata_ref_clk is a reference clock to the SATA phy.
This fixes SATA malfunction across suspend/resume or when
SATA driver is used as a module.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sata_ref_clk is a reference clock to the SATA phy.
This fixes SATA malfunction across suspend/resume or when
SATA driver is used as a module.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a device node for the System Controller, with subnodes that
represent the hardware power area hierarchy.
Hook up all devices to their respective PM domains.
Note that unlike on R-Mobile A1 (r8a7740), PM domain D4 can be powered
down without ill effects on s2ram behavior, just like on SH-Mobile AP4
(sh7372). Hence we can postpone adding a (minimal) device node for the
Coresight-ETM hardware block.
The System Controller is also used by the R-Mobile Reset driver, which
can now restart the system.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a node for the Private Timer and Watchdog, as found in the Cortex-A9
MPCore.
Without this, there's no clocksource available during early kernel
initialization, before cmt1 is initialized, leading to a lock-up if
CONFIG_CPU_IDLE=y.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the sh73a0 generic multiplatform case has the same feature set
as the kzm9g DT reference board code, we get rid of the latter.
DT reference code in the future shall make use of the sh73a0
multiplatform support code with the generic SoC machine vector.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move the Ethernet node from the root of the device tree to the BSC node,
as it's connected to the Bus State Controller. This allows the system
to know the right position of the Ethernet node in the clock and PM
domain hierarchy, and manage the clock and PM domain appropriately.
Also rename the node's name from "lan9220" to "ethernet", to conform to
ePAPR generic name recomendations.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a node for the Bus State Controller (BSC) on sh73a0, to which
multiple external devices can be connected.
The BSC is driven by the ZB clock, and located in PM domain A4S.
A reference to the latter will be added later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Build the sh73a0 KZM9G board DTB in case of Multiplatform.
The DT reference case will be removed in the future and
can be ignored for now.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sync the two DTS for the KZM9G board. The target is the file
"sh73a0-kzm9g.dts" and it is made identical to the DT reference
case with the exception of the compatbile string. In the future
the DT reference file will go away.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
[geert: Update for recent changes to sh73a0-kzm9g-reference.dts]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since ("ARM: shmobile: r8a73a4: ape6evm: Remove legacy platform"),
ape6evm is restricted to booting from DT, so chosen/stdout-path is
always used, and we can drop the "console=" parameter from
chosen/bootargs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the r8a73a4 generic multiplatform case has the same features as the
APE6EVM DT reference board code, we get rid of the latter. DT reference
code in the future shall make use of the r8a73a4 multiplatform support code
with the generic SoC machine vector.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[geert: Update Documentation/devicetree/bindings/arm/shmobile.txt]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
