DPCD 2009h "Synchronization latency in sink" has bits that tell us the
maximum number of frames sink can take to resynchronize to source timing
when exiting PSR. More importantly, as per eDP 1.4b, this is the "Minimum
number of frames following PSR exit that the Source device needs to
wait for PSR entry."
We currently use this value only to setup the number frames to wait before
PSR2 selective update. But, based on the above description it makes more
sense to use this to configure idle frames for both PSR1 and and PSR2. This
will ensure we wait the required number of frames before
activation whether it is PSR1 or PSR2.
The minimum number of idle frames remains 6, while allowing sink
synchronization latency and VBT to increase this value.
This also solves the flip-flop between sink and source frames that I
noticed on my Thinkpad X260 during PSR exit. This specific panel has a
value of 8h, which according to the spec means the "Source device must
wait for more than eight active frames after PSR exit before initiating PSR
entry. (In this case, should be provided by the panel supplier.)" VBT
however has a value of 0.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Jose Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180525033047.7596-1-dhinakaran.pandiyan@intel.com
PSR hardware and hence the driver code for VLV and CHV deviates a lot from
their DDI counterparts. While the feature has been disabled for a long time
now, retaining support for these platforms is a maintenance burden. There
have been multiple refactoring commits to just keep the existing code for
these platforms in line with the rest. There are known issues that need to
be fixed to enable PSR on these platforms, and there is no PSR capable
platform in CI to ensure the code does not break again if we get around to
fixing the existing issues. On account of all these reasons, let's nuke
this code for now and bring it back if a need arises in the future.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180511230059.19387-1-dhinakaran.pandiyan@intel.com
For psr block #9, the vbt description has moved to options [0-3] for
TP1,TP2,TP3 Wakeup time from decimal value without any change to vbt
structure. Since spec does not mention from which VBT version this
change was added to vbt.bsf file, we cannot depend on bdb->version check
to change for all the platforms.
There is RCR inplace for GOP team to provide the version number
to make generic change. Since Kabylake with bdb version 209 is having this
change, limiting this change to gen9_bc and version 209+ to unblock google.
Tested on skl(bdb version 203,without options) and
kabylake(bdb version 209,212) having new options.
bspec 20131
v2: (Jani and Rodrigo)
move the 165 version check to intel_bios.c
v3: Jani
Move the abstraction to intel_bios.
v4: Jani
Rename tp*_wakeup_time to have "us" suffix.
For values outside range[0-3],default to max 2500us.
Old decimal value was wake up time in multiples of 100us.
v5: Jani and Rodrigo
Handle option 2 in default condition.
Print oustide range value.
For negetive values default to 2500us.
v6: Jani
Handle default first and then fall through for case 2.
v7: Rodrigo
Apply this change for IS_GEN9_BC and vbt version > 209
v8: Puthik
Add new function vbt_psr_to_us.
v9: Jani
Change to v7 version as it's more readable.
DK
add comment /*fall through*/ after case2.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Puthikorn Voravootivat <puthik@chromium.org>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1526981243-2745-1-git-send-email-vathsala.nagaraju@intel.com
Any write in any display register was causing HW to exit PSR,
masking it to allow more power savings. Writes to pipe related
registers will still cause HW to exit PSR.
This is already masked for PSR2.
It also do not break the Display WA #0884, writes to CURSURFLIVE
are still causing hardware to exit PSR. This was tested in CNL machine
by triggering a write to CURSURFLIVE when a debugfs was read by user.
Bspec: 7721 and 8042
v4: Checked that it do not breaks WA #0884 and added this information
to the commit message.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180425212334.21109-1-jose.souza@intel.com
Interrupts other than the one for AUX errors are required only for debug,
so unmask them via debugfs when the user requests debug.
User can make such a request with
echo 1 > <DEBUG_FS>/dri/0/i915_edp_psr_debug
There are no locks to serialize PSR debug enabling from
irq_postinstall() and debugfs for simplicity. As irq_postinstall() is
called only during module initialization/resume and IGT subtests
aren't expected to modify PSR debug at those times, we should be safe.
v2: Unroll loops (Ville)
Avoid resetting error mask bits.
v3: Unmask interrupts in postinstall() if debug was still enabled.
Avoid RMW (Ville)
v4: Avoid extra IMR write introduced in the previous version.(Jose)
Style changes, renames (Jose).
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Jose Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405013717.24254-1-dhinakaran.pandiyan@intel.com
Although i915 don't implement aux sync frame through tests was
findout that pannels can do selective update when the y-coordinate
is also included in SDP, that is why it is required to run PSR2 in
i915.
So moving to only one place the sink requirements that the actual
driver needs to enable PSR2.
Also intel_psr2_config_valid() is called every time the crtc config
is computed, wasting some time every time it was checking for
Y coordinate requirement.
This allow us to nuke y_cord_support and some of VSC setup code that
was handling a scenario that would never happen(PSR2 without Y
coordinate).
Also here renaming intel_dp_get_y_cord_status() to
intel_dp_get_y_coord_required() as it more accurate to the name and
function of bit according to eDP spec.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-4-jose.souza@intel.com
eDP spec states that aux frame is required to do PSR2 selective
update but i915 don't fully implement it. It sends the aux frame
sync messages but the value is always zero as the GTC is not enabled
in driver.
Through tests was findout that pannels can do selective update when
the y-coordinate is also included in SDP, that is why it is required
to run PSR2 in i915.
A dummy value is not useful at all to sink, so removing everything
related to aux frame sync, if GTC is enabled we can bring this back.
Cc: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-3-jose.souza@intel.com
HSW and BDW have SRD_AUX_{CTL, STATUS} registers that the driver needs to
setup for the HW to use whenever exiting PSR. SKL+ hardware use hardcoded
values for the same and do not need any registers to be setup. So, use
drm_dp_dpcd_writeb() for a one-time write during PSR enable and setup the
PSR aux registers on HSW and BDW for later use by HW.
We also end up writing to reserved bits in SRD_AUX_CTL by reusing
intel_dp->get_aux_send_ctl() for HSW and BDW, fix this.
Since the AUX register setup is source side programming, move the call
to enable_source() from enable_sink().
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Jose Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180313034646.3721-2-dhinakaran.pandiyan@intel.com
So far we are using frontbuffer tracking for everything
and ignoring that PSR has a HW capable HW tracking for many
modern usages of GPU on Core platforms and newer Atom ones.
One reason for that is that we were trying to keep same
infrastructure in place for VLV/CHV than the rest of platforms.
But also because when this infrastructure was created
the front-buffer-tracking origin wasn't that good and stable
how it is today after Paulo reworked it to attend FBC cases.
However this PSR implementation without HW tracking died
on gen8LP. And newer platforms are starting to demand more HW
tracking specially with PSR2 cases in mind.
By disabling and re-enabling PSR totally every time we believe
someone is going to change the front buffer content we don't
allow PSR HW tracking to do this job and specially compromising
the whole idea of PSR2 case where the HW tracking detect only
the damaged area and do a partial screen update.
So, from now on, on the platforms that has hw_tracking let's
rely more on HW tracking.
This also is the case in used by other drivers and more validated
by SV teams. So I hope that this will lead us to less misterious
bugs.
v2: Only do this for platform that actually has hw tracking.
v3 from DK
Do this only for flips, small gradual changes are better.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Jose Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307033420.3086-3-dhinakaran.pandiyan@intel.com
WA 0884:bxt:all,cnl:*:A - "When FBC is enabled with eDP PSR,
the CPU host modify writes may not get updated on the Display
as expected.
WA: Write 0x00000000 to CUR_SURFLIVE_A with every CPU
host modify write to trigger PSR exit."
We can also find on spec other cases where they describe
bogus writes to cursor registers to force PSR exit with
HW tracking. And it was confirmed by HW engineers that
this Wa can be safely applied for any frontbuffer activity.
So let's use this more and more here instead of forcibly
disable and re-enable PSR everytime that we have a simple
reliable flush case.
Other commits improve the fbcon/fbdev use a lot, but this
approach is the only when where we can get a fully reliable
console with no slowness or missed frames and PSR still
enabled and active.
v2: - Rebase on drm-tip
- (DK) Add a comment to explain that WA
tells about writing 0 to CUR_SURFLIVE_A but we write to
CUR_SURFLIVE(pipe).
v3: Wa doesn't work on PSR2.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309005218.26772-1-rodrigo.vivi@intel.com
We can still use PSR1 when PSR2 conditions are not met.
So, let's split the check in a way that we make sure has_psr
gets set independently of PSR2 criteria.
v2: Duh! Handle proper return to avoid breaking PSR2.
v3: (DK):
- better name for psr2 conditions check function
- Don't remove FIXME block and psr2.support check.
- Add a debug message to show us what PSR or PSR2 is
getting enabled now we have ways to enabled PSR on
PSR2 panels.
- s/PSR2 disabled/PSR2 not enabled
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180227212913.14083-2-rodrigo.vivi@intel.com
Now that the infoframe hooks are part of the intel_dig_port, we can use
the normal .write_infoframe() hook to update the VSC SDP. We do need to
deal with the size difference between the VSC DIP and the others though.
Another minor snag is that the compiler will complain to use if we keep
using enum hdmi_infoframe_type type and passing in the DP define instead,
so et's just change to unsigned int all over for the inforframe type.
v2: Rebase due to other PSR changes
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171013194051.19286-1-ville.syrjala@linux.intel.com
