[ Upstream commit facc173cf700e55b2ad249ecbd3a7537f7315691 ]
Insufficient space was being reserved in the page used for packet
reception, so the interface MTU could be set too large to still have
room for the contents of the packet when doing XDP redirect. This
resulted in the following message when redirecting a packet between
3520 and 3822 bytes with an MTU of 3822:
[311815.561880] XDP_WARN: xdp_update_frame_from_buff(line:200): Driver BUG: missing reserved tailroom
Fixes: f18c2b77b2 ("bnxt_en: optimized XDP_REDIRECT support")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c492a2530c1f05441da541307c2534230dfd59b ]
If the flow control settings have been changed, a subsequent FW reset
may cause the ethernet link to toggle unnecessarily. This link toggle
will increase the down time by a few seconds.
The problem is caused by bnxt_update_phy_setting() detecting a false
mismatch in the flow control settings between the stored software
settings and the current FW settings after the FW reset. This mismatch
is caused by the AUTONEG bit added to link_info->req_flow_ctrl in an
inconsistent way in bnxt_set_pauseparam() in autoneg mode. The AUTONEG
bit should not be added to link_info->req_flow_ctrl.
Reviewed-by: Colin Winegarden <colin.winegarden@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d3ea3d402db94b61075617e71b67459a714a502 ]
GCC12 appears to be much smarter about its dependency tracking and is
aware that the relaxed variants are just normal loads and stores and
this is causing problems like:
[ 210.074549] ------------[ cut here ]------------
[ 210.079223] NETDEV WATCHDOG: enabcm6e4ei0 (bcmgenet): transmit queue 1 timed out
[ 210.086717] WARNING: CPU: 1 PID: 0 at net/sched/sch_generic.c:529 dev_watchdog+0x234/0x240
[ 210.095044] Modules linked in: genet(E) nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat]
[ 210.146561] ACPI CPPC: PCC check channel failed for ss: 0. ret=-110
[ 210.146927] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G E 5.17.0-rc7G12+ #58
[ 210.153226] CPPC Cpufreq:cppc_scale_freq_workfn: failed to read perf counters
[ 210.161349] Hardware name: Raspberry Pi Foundation Raspberry Pi 4 Model B/Raspberry Pi 4 Model B, BIOS EDK2-DEV 02/08/2022
[ 210.161353] pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 210.161358] pc : dev_watchdog+0x234/0x240
[ 210.161364] lr : dev_watchdog+0x234/0x240
[ 210.161368] sp : ffff8000080a3a40
[ 210.161370] x29: ffff8000080a3a40 x28: ffffcd425af87000 x27: ffff8000080a3b20
[ 210.205150] x26: ffffcd425aa00000 x25: 0000000000000001 x24: ffffcd425af8ec08
[ 210.212321] x23: 0000000000000100 x22: ffffcd425af87000 x21: ffff55b142688000
[ 210.219491] x20: 0000000000000001 x19: ffff55b1426884c8 x18: ffffffffffffffff
[ 210.226661] x17: 64656d6974203120 x16: 0000000000000001 x15: 6d736e617274203a
[ 210.233831] x14: 2974656e65676d63 x13: ffffcd4259c300d8 x12: ffffcd425b07d5f0
[ 210.241001] x11: 00000000ffffffff x10: ffffcd425b07d5f0 x9 : ffffcd4258bdad9c
[ 210.248171] x8 : 00000000ffffdfff x7 : 000000000000003f x6 : 0000000000000000
[ 210.255341] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000001000
[ 210.262511] x2 : 0000000000001000 x1 : 0000000000000005 x0 : 0000000000000044
[ 210.269682] Call trace:
[ 210.272133] dev_watchdog+0x234/0x240
[ 210.275811] call_timer_fn+0x3c/0x15c
[ 210.279489] __run_timers.part.0+0x288/0x310
[ 210.283777] run_timer_softirq+0x48/0x80
[ 210.287716] __do_softirq+0x128/0x360
[ 210.291392] __irq_exit_rcu+0x138/0x140
[ 210.295243] irq_exit_rcu+0x1c/0x30
[ 210.298745] el1_interrupt+0x38/0x54
[ 210.302334] el1h_64_irq_handler+0x18/0x24
[ 210.306445] el1h_64_irq+0x7c/0x80
[ 210.309857] arch_cpu_idle+0x18/0x2c
[ 210.313445] default_idle_call+0x4c/0x140
[ 210.317470] cpuidle_idle_call+0x14c/0x1a0
[ 210.321584] do_idle+0xb0/0x100
[ 210.324737] cpu_startup_entry+0x30/0x8c
[ 210.328675] secondary_start_kernel+0xe4/0x110
[ 210.333138] __secondary_switched+0x94/0x98
The assumption when these were relaxed seems to be that device memory
would be mapped non reordering, and that other constructs
(spinlocks/etc) would provide the barriers to assure that packet data
and in memory rings/queues were ordered with respect to device
register reads/writes. This itself seems a bit sketchy, but the real
problem with GCC12 is that it is moving the actual reads/writes around
at will as though they were independent operations when in truth they
are not, but the compiler can't know that. When looking at the
assembly dumps for many of these routines its possible to see very
clean, but not strictly in program order operations occurring as the
compiler would be free to do if these weren't actually register
reads/write operations.
Its possible to suppress the timeout with a liberal bit of dma_mb()'s
sprinkled around but the device still seems unable to reliably
send/receive data. A better plan is to use the safer readl/writel
everywhere.
Since this partially reverts an older commit, which notes the use of
the relaxed variants for performance reasons. I would suggest that
any performance problems with this commit are targeted at relaxing only
the performance critical code paths after assuring proper barriers.
Fixes: 69d2ea9c79 ("net: bcmgenet: Use correct I/O accessors")
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220310045358.224350-1-jeremy.linton@arm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f643c88c8d240eba0ea25c2e095a46515ff46e9 ]
The RXCHK block will return a partial checksum of 0 if it encounters
a problem while receiving a packet. Since a 1's complement sum can
only produce this result if no bits are set in the received data
stream it is fair to treat it as an invalid partial checksum and
not pass it up the stack.
Fixes: 8101553978 ("net: bcmgenet: use CHECKSUM_COMPLETE for NETIF_F_RXCSUM")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220317012812.1313196-1-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 424e7834e293936a54fcf05173f2884171adc5a3 ]
Commit b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
added request_firmware() logic in probe() which caused
load failure when firmware file is not present in initrd (below),
as access to firmware file is not feasible during probe.
Direct firmware load for bnx2x/bnx2x-e2-7.13.15.0.fw failed with error -2
Direct firmware load for bnx2x/bnx2x-e2-7.13.21.0.fw failed with error -2
This patch fixes this issue by -
1. Removing request_firmware() logic from the probe()
such that .ndo_open() handle it as it used to handle
it earlier
2. Given request_firmware() is removed from probe(), so
driver has to relax FW version comparisons a bit against
the already loaded FW version (by some other PFs of same
adapter) to allow different compatible/close enough FWs with which
multiple PFs may run with (in different environments), as the
given PF who is in probe flow has no idea now with which firmware
file version it is going to initialize the device in ndo_open()
Link: https://lore.kernel.org/all/46f2d9d9-ae7f-b332-ddeb-b59802be2bab@molgen.mpg.de/
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Fixes: b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220316214613.6884-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00b022f8f876a3a036b0df7f971001bef6398605 ]
Some of the bcmgenet platforms don't correctly support WOL, yet
ethtool returns:
"Supports Wake-on: gsf"
which is false.
Ideally if there isn't a wol_irq, or there is something else that
keeps the device from being able to wakeup it should display:
"Supports Wake-on: d"
This patch checks whether the device can wakup, before using the
hard-coded supported flags. This corrects the ethtool reporting, as
well as the WOL configuration because ethtool verifies that the mode
is supported before attempting it.
Fixes: c51de7f397 ("net: bcmgenet: add Wake-on-LAN support code")
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220310045535.224450-1-jeremy.linton@arm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 84d3c83e6ea7d46cf3de3a54578af73eb24a64f2 upstream.
ethtool --show-fec <interface> does not show anything when the Active
FEC setting in the chip is set to None. Fix it to properly return
ETHTOOL_FEC_OFF in that case.
Fixes: 8b2775890a ("bnxt_en: Report FEC settings to ethtool.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e13ad1443684f7afaff24cf207e85e97885256bd upstream.
Commit b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0") added
new firmware support in the driver with maintaining older firmware
compatibility. However, older firmware was not added in MODULE_FIRMWARE()
which caused missing firmware files in initrd image leading to driver load
failure from initrd. This patch adds MODULE_FIRMWARE() for older firmware
version to have firmware files included in initrd.
Fixes: b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215627
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220223085720.12021-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 802d4d207e75d7208ff75adb712b556c1e91cf1c upstream
Commit 0a6890b9b4 ("bnx2x: Utilize FW 7.13.15.0.")
added validation for fastpath HSI versions for different
client init which was not meant for SR-IOV VF clients, which
resulted in firmware asserts when running VF clients with
different fastpath HSI version.
This patch along with the new firmware support in patch #1
fixes this behavior in order to not validate fastpath HSI
version for the VFs.
Fixes: 0a6890b9b4 ("bnx2x: Utilize FW 7.13.15.0.")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7a49f73059fe6147b6b78e8f674ce0d21237432 upstream
This new firmware addresses few important issues and enhancements
as mentioned below -
- Support direct invalidation of FP HSI Ver per function ID, required for
invalidating FP HSI Ver prior to each VF start, as there is no VF start
- BRB hardware block parity error detection support for the driver
- Fix the FCOE underrun flow
- Fix PSOD during FCoE BFS over the NIC ports after preboot driver
- Maintains backward compatibility
This patch incorporates this new firmware 7.13.21.0 in bnx2x driver.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9deb48b53e7f4056c2eaa2dc2ee3338df619e4f6 upstream.
The driver neglects to check the result of platform_get_irq_optional()'s
call and blithely passes the negative error codes to devm_request_irq()
(which takes *unsigned* IRQ #), causing it to fail with -EINVAL.
Stop calling devm_request_irq() with the invalid IRQ #s.
Fixes: 8562056f26 ("net: bcmgenet: request Wake-on-LAN interrupt")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8b8e6e782456f1ce02a7ae914bbd5b1053f0b034 ]
The descriptor list is a shared resource across all of the transmit queues, and
the locking mechanism used today only protects concurrency across a given
transmit queue between the transmit and reclaiming. This creates an opportunity
for the SYSTEMPORT hardware to work on corrupted descriptors if we have
multiple producers at once which is the case when using multiple transmit
queues.
This was particularly noticeable when using multiple flows/transmit queues and
it showed up in interesting ways in that UDP packets would get a correct UDP
header checksum being calculated over an incorrect packet length. Similarly TCP
packets would get an equally correct checksum computed by the hardware over an
incorrect packet length.
The SYSTEMPORT hardware maintains an internal descriptor list that it re-arranges
when the driver produces a new descriptor anytime it writes to the
WRITE_PORT_{HI,LO} registers, there is however some delay in the hardware to
re-organize its descriptors and it is possible that concurrent TX queues
eventually break this internal allocation scheme to the point where the
length/status part of the descriptor gets used for an incorrect data buffer.
The fix is to impose a global serialization for all TX queues in the short
section where we are writing to the WRITE_PORT_{HI,LO} registers which solves
the corruption even with multiple concurrent TX queues being used.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211215202450.4086240-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0757491a118ae5727cf9f1c3a11544397d46596 ]
The driver does not check if hw-tc-offload is enabled for the device
before offloading a flow in the context of indirect block callback.
Fix this by checking NETIF_F_HW_TC in the features flag and rejecting
the offload request. This will avoid unnecessary dmesg error logs when
hw-tc-offload is disabled, such as these:
bnxt_en 0000:19:00.1 eno2np1: dev(ifindex=294) not on same switch
bnxt_en 0000:19:00.1 eno2np1: Error: bnxt_tc_add_flow: cookie=0xffff8dace1c88000 error=-22
bnxt_en 0000:19:00.0 eno1np0: dev(ifindex=294) not on same switch
bnxt_en 0000:19:00.0 eno1np0: Error: bnxt_tc_add_flow: cookie=0xffff8dace1c88000 error=-22
Reported-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Fixes: 627c89d00f ("bnxt_en: flow_offload: offload tunnel decap rules via indirect callbacks")
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8885ac89ce310570e5391fe0bf0ec9c7c9b4fdc ]
Smatch says:
bnx2x_init_ops.h:640 bnx2x_ilt_client_mem_op()
warn: variable dereferenced before check 'ilt' (see line 638)
Move ilt_cli variable initialization _after_ ilt validation, because
it's unsafe to deref the pointer before validation check.
Fixes: 523224a3b3 ("bnx2x, cnic, bnx2i: use new FW/HSI")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bed8b0704c9ecccc8f4a2c377d7c8e21090a82e ]
The smallest TX ring size we support must fit a TX SKB with MAX_SKB_FRAGS
+ 1. Because the first TX BD for a packet is always a long TX BD, we
need an extra TX BD to fit this packet. Define BNXT_MIN_TX_DESC_CNT with
this value to make this more clear. The current code uses a minimum
that is off by 1. Fix it using this constant.
The tx_wake_thresh to determine when to wake up the TX queue is half the
ring size but we must have at least BNXT_MIN_TX_DESC_CNT for the next
packet which may have maximum fragments. So the comparison of the
available TX BDs with tx_wake_thresh should be >= instead of > in the
current code. Otherwise, at the smallest ring size, we will never wake
up the TX queue and will cause TX timeout.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit eca4cf12acda306f851f6d2a05b1c9ef62cf0e81 upstream.
The recent patch has introduced a regression by not reading the reset
count in the ERROR_RECOVERY async event handler. We may have just
gone through a reset and the reset count has just incremented. If
we don't update the reset count in the ERROR_RECOVERY event handler,
the health check timer will see that the reset count has changed and
will initiate an unintended reset.
Restore the unconditional update of the reset count in
bnxt_async_event_process() if error recovery watchdog is enabled.
Also, update the reset count at the end of the reset sequence to
make it even more robust.
Fixes: 1b2b91831983 ("bnxt_en: Fix possible unintended driver initiated error recovery")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1b2b91831983aeac3adcbb469aa8b0dc71453f89 ]
If error recovery is already enabled, bnxt_timer() will periodically
check the heartbeat register and the reset counter. If we get an
error recovery async. notification from the firmware (e.g. change in
primary/secondary role), we will immediately read and update the
heartbeat register and the reset counter. If the timer for the next
health check expires soon after this, we may read the heartbeat register
again in quick succession and find that it hasn't changed. This will
trigger error recovery unintentionally.
The likelihood is small because we also reset fw_health->tmr_counter
which will reset the interval for the next health check. But the
update is not protected and bnxt_timer() can miss the update and
perform the health check without waiting for the full interval.
Fix it by only reading the heartbeat register and reset counter in
bnxt_async_event_process() if error recovery is trasitioning to the
enabled state. Also add proper memory barriers so that when enabling
for the first time, bnxt_timer() will see the tmr_counter interval and
perform the health check after the full interval has elapsed.
Fixes: 7e914027f7 ("bnxt_en: Enable health monitoring.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4d95c3c194de04ae7b44f850131321c7ceb9312 ]
We currently only log the error recovery settings if it is enabled.
In some cases, firmware disables error recovery after it was
initially enabled. Without logging anything, the user will not be
aware of this change in setting.
Log it when error recovery is disabled. Also, change the reset count
value from hexadecimal to decimal.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a44daa8fcbcf572545c4c1a7908b3fbb38388048 ]
Firmware is capable of generating asynchronous debug notifications.
The event data is opaque to the driver and is simply logged. Debug
notifications can be enabled by turning on hardware status messages
using the ethtool msglvl interface.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fdab8a3ade2adc123bbf5c4fdec3394560b1fb1 ]
The current asic.rev is incomplete and does not include the metal
revision. Add the metal revision and decode the complete asic
revision into the more common and readable form (A0, B0, etc).
Fixes: 7154917a12 ("bnxt_en: Refactor bnxt_dl_info_get().")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1656db67233e4259281d2ac35b25f712edbbc20b ]
The FW_PSID version components are 8 bits wide, not 4.
Fixes: db28b6c77f40 ("bnxt_en: Fix devlink info's stored fw.psid version format.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1affc01fdc6035189a5ab2a24948c9419ee0ecf2 upstream.
The call to bnxt_free_mem(..., false) in the bnxt_half_open_nic() error
path will deallocate ring descriptor memory via bnxt_free_?x_rings(),
but because irq_re_init is false, the ring info itself is not freed.
To simplify error paths, deallocation functions have generally been
written to be safe when called on unallocated memory. It should always
be safe to call dev_close(), which calls bnxt_free_skbs() a second time,
even in this semi- allocated ring state.
Calling bnxt_free_skbs() a second time with the rings already freed will
cause NULL pointer dereference. Fix it by checking the rings are valid
before proceeding in bnxt_free_tx_skbs() and
bnxt_free_one_rx_ring_skbs().
Fixes: 975bc99a4a ("bnxt_en: Refactor bnxt_free_rx_skbs().")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c3a0a018e672a9723a79b128227272562300055 upstream.
Remove the assert from the callback priv lookup function since it does
not require RTNL lock and is already protected by flow_indr_block_lock.
This will avoid warnings from being emitted to dmesg if the driver
registers its callback after an ingress qdisc was created for a
netdevice.
The warnings started after the following patch was merged:
commit 74fc4f828769 ("net: Fix offloading indirect devices dependency on qdisc order creation")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 828affc27ed43441bd1efdaf4e07e96dd43a0362 ]
Each completion ring entry has a valid bit to indicate that the entry
contains a valid completion event. The driver's main poll loop
__bnxt_poll_work() has the proper dma_rmb() to make sure the valid
bit of the next entry has been checked before proceeding further.
But when we call bnxt_rx_pkt() to process the RX event, the RX
completion event consists of two completion entries and only the
first entry has been checked to be valid. We need the same barrier
after checking the next completion entry. Add missing dma_rmb()
barriers in bnxt_rx_pkt() and other similar locations.
Fixes: 67a95e2022 ("bnxt_en: Need memory barrier when processing the completion ring.")
Reported-by: Lance Richardson <lance.richardson@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Lance Richardson <lance.richardson@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 976e52b718c3de9077fff8f3f674afb159c57fb1 ]
212 firmware broke aRFS, so disable it. Traffic may stop after ntuple
filters are inserted and deleted by the 212 firmware.
Fixes: ae10ae740a ("bnxt_en: Add new hardware RFS mode.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8d8c5d80f5e9d4586c68061b62c642752289095 ]
skbs are freed on error and not put on the ring. We may, however,
be in a situation where we're freeing the last skb of a batch,
and there is a doorbell ring pending because of xmit_more() being
true earlier. Make sure we ring the door bell in such situations.
Since errors are rare don't pay attention to xmit_more() and just
always flush the pending frames.
The busy case should be safe to be left alone because it can
only happen if start_xmit races with completions and they
both enable the queue. In that case the kick can't be pending.
Noticed while reading the code.
Fixes: 4d172f21ce ("bnxt_en: Implement xmit_more.")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01cca6b9330ac7460de44eeeb3a0607f8aae69ff ]
napi schedules DIM, napi has to be disabled first,
then DIM canceled.
Noticed while reading the code.
Fixes: 0bc0b97fca ("bnxt_en: cleanup DIM work on device shutdown")
Fixes: 6a8788f256 ("bnxt_en: add support for software dynamic interrupt moderation")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c603136c9f82833813af77185618de5af67676c ]
We can't take the tx lock from the napi poll routine, because
netpoll can poll napi at any moment, including with the tx lock
already held.
The tx lock is protecting against two paths - the disable
path, and (as Michael points out) the NETDEV_TX_BUSY case
which may occur if NAPI completions race with start_xmit
and both decide to re-enable the queue.
For the disable/ifdown path use synchronize_net() to make sure
closing the device does not race we restarting the queues.
Annotate accesses to dev_state against data races.
For the NAPI cleanup vs start_xmit path - appropriate barriers
are already in place in the main spot where Tx queue is stopped
but we need to do the same careful dance in the TX_BUSY case.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb653827c758725b149b5c924a5eb50ab4812750 ]
Set the error code if bnx2x_alloc_fw_stats_mem() fails. The current
code returns success.
Fixes: ad5afc8936 ("bnx2x: Separate VF and PF logic")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11a39259ff79b74bc99f8b7c44075a2d6d5e7ab1 ]
bnxt_half_open_nic() is called during during ethtool self test and is
protected by rtnl_lock. Firmware reset can be happening at the same
time. Only critical portions of the entire firmware reset sequence
are protected by the rtnl_lock. It is possible that bnxt_half_open_nic()
can be called when the firmware reset sequence is aborting. In that
case, bnxt_half_open_nic() needs to check if the ABORT_ERR flag is set
and abort if it is. The ethtool self test will fail but the NIC will be
brought to a consistent IF_DOWN state.
Without this patch, if bnxt_half_open_nic() were to continue in this
error state, it may crash like this:
bnxt_en 0000:82:00.1 enp130s0f1np1: FW reset in progress during close, FW reset will be aborted
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
...
Process ethtool (pid: 333327, stack limit = 0x0000000046476577)
Call trace:
bnxt_alloc_mem+0x444/0xef0 [bnxt_en]
bnxt_half_open_nic+0x24/0xb8 [bnxt_en]
bnxt_self_test+0x2dc/0x390 [bnxt_en]
ethtool_self_test+0xe0/0x1f8
dev_ethtool+0x1744/0x22d0
dev_ioctl+0x190/0x3e0
sock_ioctl+0x238/0x480
do_vfs_ioctl+0xc4/0x758
ksys_ioctl+0x84/0xb8
__arm64_sys_ioctl+0x28/0x38
el0_svc_handler+0xb0/0x180
el0_svc+0x8/0xc
Fixes: a1301f08c5 ("bnxt_en: Check abort error state in bnxt_open_nic().")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96bdd4b9ea7ef9a12db8fdd0ce90e37dffbd3703 ]
Only pass supported VLAN protocol IDs for stripped VLAN tags to the
stack. The stack will hit WARN() if the protocol ID is unsupported.
Existing firmware sets up the chip to strip 0x8100, 0x88a8, 0x9100.
Only the 1st two protocols are supported by the kernel.
Fixes: a196e96bb6 ("bnxt_en: clean up VLAN feature bit handling")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6cd657cb3ee6f4de57e635b126ffbe0e51d00f1a ]
In the BNXT_FW_RESET_STATE_POLL_VF state in bnxt_fw_reset_task() after all
VFs have unregistered, we need to check for BNXT_STATE_ABORT_ERR after
we acquire the rtnl_lock. If the flag is set, we need to abort.
Fixes: 230d1f0de7 ("bnxt_en: Handle firmware reset.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c9f046bc377efd1f5e26e74817d5f96e9506c86 ]
The capabilities can change after firmware upgrade/downgrade, so we
should get the up-to-date RoCE capabilities everytime bnxt_ulp_probe()
is called.
Fixes: 2151fe0830 ("bnxt_en: Handle RESET_NOTIFY async event from firmware.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c81cfb6256d90ea5ba4a6fb280ea3b171be4e05c ]
If device is already disabled in reset path and PCI io error is
detected before the device could be enabled, driver could
call pci_disable_device() for already disabled device. Fix this
problem by calling pci_disable_device() only if the device is already
enabled.
Fixes: 6316ea6db9 ("bnxt_en: Enable AER support.")
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2b452550a203d88112eaf0ba9fc4b750a000b496 upstream.
Make sure that we disable each of the TX and RX queues in the TDMA and
RDMA control registers. This is a correctness change to be symmetrical
with the code that enables the TX and RX queues.
Tested-by: Maxime Ripard <maxime@cerno.tech>
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a3c680aa2c12c90c44af383fe6882a39875ab81 upstream.
Setting the EXT_ENERGY_DET_MASK bit allows the port energy detection
logic of the internal PHY to prevent the system from sleeping. Some
internal PHYs will report that energy is detected when the network
interface is closed which can prevent the system from going to sleep
if WoL is enabled when the interface is brought down.
Since the driver does not support waking the system on this logic,
this commit clears the bit whenever the internal PHY is powered up
and the other logic for manipulating the bit is removed since it
serves no useful function.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 74325bf0104573c6dfce42837139aeef3f34be76 ]
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2ac9800cfe0f8da16abc4e74e003440361c112e ]
The Broadcom UniMAC MDIO bus from mdio-bcm-unimac module comes too late.
So, GENET cannot find the ethernet PHY on UniMAC MDIO bus. This leads
GENET fail to attach the PHY as following log:
bcmgenet fd580000.ethernet: GENET 5.0 EPHY: 0x0000
...
could not attach to PHY
bcmgenet fd580000.ethernet eth0: failed to connect to PHY
uart-pl011 fe201000.serial: no DMA platform data
libphy: bcmgenet MII bus: probed
...
unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO bus
This patch adds the soft dependency to load mdio-bcm-unimac module
before genet module to avoid the issue.
Fixes: 9a4e796970 ("net: bcmgenet: utilize generic Broadcom UniMAC MDIO controller driver")
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=213485
Signed-off-by: Jian-Hong Pan <jhp@endlessos.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03400aaa69f916a376e11526cf591901a96a3a5c ]
bnxt_ethtool_init() may have allocated some memory and we need to
call bnxt_ethtool_free() to properly unwind if bnxt_init_one()
fails.
Fixes: 7c38091814 ("bnxt_en: Refactor bnxt_init_one() and turn on TPA support on 57500 chips.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c12e1643d2738bcd4e26252ce531878841dd3f38 ]
TQM fastpath ring needs to be sized to store both the requester
and responder side of RoCE QPs in TQM for supporting bi-directional
tests. Fix bnxt_alloc_ctx_mem() to multiply the RoCE QPs by a factor of
2 when computing the number of entries for TQM fastpath ring. This
fixes an RX pipeline stall issue when running bi-directional max
RoCE QP tests.
Fixes: c7dd7ab4b2 ("bnxt_en: Improve TQM ring context memory sizing formulas.")
Signed-off-by: Rukhsana Ansari <rukhsana.ansari@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0afd6a4e8028cc487c240b6cfe04094e45a306e4 ]
There is a missing bnxt_probe_phy() call in bnxt_fw_init_one() to
rediscover the PHY capabilities after a firmware reset. This can cause
some PHY related functionalities to fail after a firmware reset. For
example, in multi-host, the ability for any host to configure the PHY
settings may be lost after a firmware reset.
Fixes: ec5d31e3c1 ("bnxt_en: Handle firmware reset status during IF_UP.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 702279d2ce4650000bb6302013630304e359dc13 ]
There was a typo in the code that checks for 64K BNXT_PAGE_SHIFT in
bnxt_hwrm_set_pg_attr(). Fix it and make the code more understandable
with a new macro BNXT_SET_CTX_PAGE_ATTR().
Fixes: 1b9394e5a2 ("bnxt_en: Configure context memory on new devices.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab21494be9dc7d62736c5fcd06be65d49df713ee ]
Otherwise, some of the recently added HyperV VF IDs would not be
recognized as VF devices and they would not initialize properly.
Fixes: 7fbf359bb2c1 ("bnxt_en: Add PCI IDs for Hyper-V VF devices.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28c66b6da4087b8cfe81c2ec0a46eb6116dafda9 ]
Fix to return -EPERM from the error handling case instead of 0, as done
elsewhere in this function.
Fixes: b6016b7673 ("[BNX2]: New Broadcom gigabit network driver.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
