PTP hardware filter configuration performed by the driver for a given
user requested config is not correct for some of the PTP modes.
Following changes are needed for PTP config-filter implementation.
1. NIG_REG_TX_PTP_EN register - Bits 0/1/2 respectively enables
TimeSync/"V1 frame format support"/"V2 frame format support" on
the TX side. Set the associated bits based on the user request.
2. ptp4l application fails to operate in Peer Delay mode. Following
changes are needed to fix this,
a. Driver should enable (set to 0) DA #1-related bits for IPv4,
IPv6 and MAC destination addresses in these registers:
NIG_REG_TX_LLH_PTP_RULE_MASK
NIG_REG_LLH_PTP_RULE_MASK
b. NIG_REG_LLH_PTP_PARAM_MASK/NIG_REG_TX_LLH_PTP_PARAM_MASK should
be set to 0x0 in all modes.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull fs/compat.c cleanups from Al Viro:
"More moving of compat syscalls from fs/compat.c to fs/*.c where the
native counterparts live.
And death to compat_sys_getdents64() - the only architecture that used
to need it was ia64, and _that_ has lost biarch support quite a few
years ago"
* 'work.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs/compat.c: trim unused includes
move compat_rw_copy_check_uvector() over to fs/read_write.c
fhandle: move compat syscalls from compat.c
open: move compat syscalls from compat.c
stat: move compat syscalls from compat.c
fcntl: move compat syscalls from compat.c
readdir: move compat syscalls from compat.c
statfs: move compat syscalls from compat.c
utimes: move compat syscalls from compat.c
move compat select-related syscalls to fs/select.c
Remove compat_sys_getdents64()
Pull splice updates from Al Viro:
"These actually missed the last cycle; the branch itself is from last
December"
* 'work.splice' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
make nr_pages calculation in default_file_splice_read() a bit less ugly
splice/tee/vmsplice: validate flags
splice_pipe_desc: kill ->flags
remove spd_release_page()
Pull iov_iter updates from Al Viro:
"Cleanups that sat in -next + -stable fodder that has just missed 4.11.
There's more iov_iter work in my local tree, but I'd prefer to push
the stuff that had been in -next first"
* 'work.iov_iter' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
iov_iter: don't revert iov buffer if csum error
generic_file_read_iter(): make use of iov_iter_revert()
generic_file_direct_write(): make use of iov_iter_revert()
orangefs: use iov_iter_revert()
sctp: switch to copy_from_iter_full()
net/9p: switch to copy_from_iter_full()
switch memcpy_from_msg() to copy_from_iter_full()
rds: make use of iov_iter_revert()
Pull hardened usercopy updates from Kees Cook:
"A couple hardened usercopy changes:
- drop now unneeded is_vmalloc_or_module() check (Laura Abbott)
- use enum instead of literals for stack frame API (Sahara)"
* tag 'usercopy-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
mm/usercopy: Drop extra is_vmalloc_or_module() check
usercopy: Move enum for arch_within_stack_frames()
Pull pstore updates from Kees Cook:
"This has a large internal refactoring along with several smaller
fixes.
- constify compression structures; Bhumika Goyal
- restore powerpc dumping; Ankit Kumar
- fix more bugs in the rarely exercises module unloading logic
- reorganize filesystem locking to fix problems noticed by lockdep
- refactor internal pstore APIs to make development and review
easier:
- improve error reporting
- add kernel-doc structure and function comments
- avoid insane argument passing by using a common record
structure"
* tag 'pstore-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (23 commits)
pstore: Solve lockdep warning by moving inode locks
pstore: Fix flags to enable dumps on powerpc
pstore: Remove unused vmalloc.h in pmsg
pstore: simplify write_user_compat()
pstore: Remove write_buf() callback
pstore: Replace arguments for write_buf_user() API
pstore: Replace arguments for write_buf() API
pstore: Replace arguments for erase() API
pstore: Do not duplicate record metadata
pstore: Allocate records on heap instead of stack
pstore: Pass record contents instead of copying
pstore: Always allocate buffer for decompression
pstore: Replace arguments for write() API
pstore: Replace arguments for read() API
pstore: Switch pstore_mkfile to pass record
pstore: Move record decompression to function
pstore: Extract common arguments into structure
pstore: Add kernel-doc for struct pstore_info
pstore: Improve register_pstore() error reporting
pstore: Avoid race in module unloading
...
Pull documentation update from Jonathan Corbet:
"A reasonably busy cycle for documentation this time around. There is a
new guide for user-space API documents, rather sparsely populated at
the moment, but it's a start. Markus improved the infrastructure for
converting diagrams. Mauro has converted much of the USB documentation
over to RST. Plus the usual set of fixes, improvements, and tweaks.
There's a bit more than the usual amount of reaching out of
Documentation/ to fix comments elsewhere in the tree; I have acks for
those where I could get them"
* tag 'docs-4.12' of git://git.lwn.net/linux: (74 commits)
docs: Fix a couple typos
docs: Fix a spelling error in vfio-mediated-device.txt
docs: Fix a spelling error in ioctl-number.txt
MAINTAINERS: update file entry for HSI subsystem
Documentation: allow installing man pages to a user defined directory
Doc/PM: Sync with intel_powerclamp code behavior
zr364xx.rst: usb/devices is now at /sys/kernel/debug/
usb.rst: move documentation from proc_usb_info.txt to USB ReST book
convert philips.txt to ReST and add to media docs
docs-rst: usb: update old usbfs-related documentation
arm: Documentation: update a path name
docs: process/4.Coding.rst: Fix a couple of document refs
docs-rst: fix usb cross-references
usb: gadget.h: be consistent at kernel doc macros
usb: composite.h: fix two warnings when building docs
usb: get rid of some ReST doc build errors
usb.rst: get rid of some Sphinx errors
usb/URB.txt: convert to ReST and update it
usb/persist.txt: convert to ReST and add to driver-api book
usb/hotplug.txt: convert to ReST and add to driver-api book
...
struct timespec is not y2038 safe.
Audit timestamps are recorded in string format into
an audit buffer for a given context.
These mark the entry timestamps for the syscalls.
Use y2038 safe struct timespec64 to represent the times.
The log strings can handle this transition as strings can
hold upto 1024 characters.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Paul Moore <paul@paul-moore.com>
Acked-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
We were setting the portid incorrectly in the netlink message headers,
fix that to always be 0 (nlmsg_pid = 0).
Signed-off-by: Paul Moore <paul@paul-moore.com>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Remove the request_idx parameter, which can't be used safely now that we
support I/O schedulers with blk-mq. Except for a superflous check in
mtip32xx it was unused anyway.
Also pass the tag_set instead of just the driver data - this allows drivers
to avoid some code duplication in a follow on cleanup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since commit 8425339492 ("remove the mg_disk driver") removed the
only caller of elevator_change(), also remove the elevator_change()
function itself.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Linus noticed that the <linux/rcu_segcblist.h> has huge inline functions
which should not be inline at all.
As a first step in cleaning this up, move them all to kernel/rcu/ and
only keep an absolute minimum of data type defines in the header:
before: -rw-r--r-- 1 mingo mingo 22284 May 2 10:25 include/linux/rcu_segcblist.h
after: -rw-r--r-- 1 mingo mingo 3180 May 2 10:22 include/linux/rcu_segcblist.h
More can be done, such as uninlining the large functions, which inlining
is unjustified even if it's an RCU internal matter.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
We needed the lock to avoid racing with creation of the irqchip on x86. As
kvm_set_irq_routing() calls srcu_synchronize_expedited(), this lock
might be held for a longer time.
Let's introduce an arch specific callback to check if we can actually
add irq routes. For x86, all we have to do is check if we have an
irqchip in the kernel. We don't need kvm->lock at that point as the
irqchip is marked as inititalized only when actually fully created.
Reported-by: Steve Rutherford <srutherford@google.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Fixes: 1df6ddede1 ("KVM: x86: race between KVM_SET_GSI_ROUTING and KVM_CREATE_IRQCHIP")
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull x86 mm updates from Ingo Molnar:
"The main x86 MM changes in this cycle were:
- continued native kernel PCID support preparation patches to the TLB
flushing code (Andy Lutomirski)
- various fixes related to 32-bit compat syscall returning address
over 4Gb in applications, launched from 64-bit binaries - motivated
by C/R frameworks such as Virtuozzo. (Dmitry Safonov)
- continued Intel 5-level paging enablement: in particular the
conversion of x86 GUP to the generic GUP code. (Kirill A. Shutemov)
- x86/mpx ABI corner case fixes/enhancements (Joerg Roedel)
- ... plus misc updates, fixes and cleanups"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (62 commits)
mm, zone_device: Replace {get, put}_zone_device_page() with a single reference to fix pmem crash
x86/mm: Fix flush_tlb_page() on Xen
x86/mm: Make flush_tlb_mm_range() more predictable
x86/mm: Remove flush_tlb() and flush_tlb_current_task()
x86/vm86/32: Switch to flush_tlb_mm_range() in mark_screen_rdonly()
x86/mm/64: Fix crash in remove_pagetable()
Revert "x86/mm/gup: Switch GUP to the generic get_user_page_fast() implementation"
x86/boot/e820: Remove a redundant self assignment
x86/mm: Fix dump pagetables for 4 levels of page tables
x86/mpx, selftests: Only check bounds-vs-shadow when we keep shadow
x86/mpx: Correctly report do_mpx_bt_fault() failures to user-space
Revert "x86/mm/numa: Remove numa_nodemask_from_meminfo()"
x86/espfix: Add support for 5-level paging
x86/kasan: Extend KASAN to support 5-level paging
x86/mm: Add basic defines/helpers for CONFIG_X86_5LEVEL=y
x86/paravirt: Add 5-level support to the paravirt code
x86/mm: Define virtual memory map for 5-level paging
x86/asm: Remove __VIRTUAL_MASK_SHIFT==47 assert
x86/boot: Detect 5-level paging support
x86/mm/numa: Remove numa_nodemask_from_meminfo()
...
Pull x86 debug updates from Ingo Molnar:
"The biggest update is the addition of USB3 debug port based
early-console.
Greg was fine with the USB changes and with the routing of these
patches:
https://www.spinics.net/lists/linux-usb/msg155093.html"
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
usb/doc: Add document for USB3 debug port usage
usb/serial: Add DBC debug device support to usb_debug
x86/earlyprintk: Add support for earlyprintk via USB3 debug port
usb/early: Add driver for xhci debug capability
x86/timers: Add simple udelay calibration
Pull x86 asm updates from Ingo Molnar:
"The main changes in this cycle were:
- unwinder fixes and enhancements
- improve ftrace interaction with the unwinder
- optimize the code footprint of WARN() and related debugging
constructs
- ... plus misc updates, cleanups and fixes"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86/unwind: Dump all stacks in unwind_dump()
x86/unwind: Silence more entry-code related warnings
x86/ftrace: Fix ebp in ftrace_regs_caller that screws up unwinder
x86/unwind: Remove unused 'sp' parameter in unwind_dump()
x86/unwind: Prepend hex mask value with '0x' in unwind_dump()
x86/unwind: Properly zero-pad 32-bit values in unwind_dump()
x86/unwind: Ensure stack pointer is aligned
debug: Avoid setting BUGFLAG_WARNING twice
x86/unwind: Silence entry-related warnings
x86/unwind: Read stack return address in update_stack_state()
x86/unwind: Move common code into update_stack_state()
debug: Fix __bug_table[] in arch linker scripts
debug: Add _ONCE() logic to report_bug()
x86/debug: Define BUG() again for !CONFIG_BUG
x86/debug: Implement __WARN() using UD0
x86/ftrace: Use Makefile logic instead of #ifdef for compiling ftrace_*.o
x86/ftrace: Add -mfentry support to x86_32 with DYNAMIC_FTRACE set
x86/ftrace: Clean up ftrace_regs_caller
x86/ftrace: Add stack frame pointer to ftrace_caller
x86/ftrace: Move the ftrace specific code out of entry_32.S
...
Pull x86 boot updates from Ingo Molnar:
"The biggest changes in this cycle were:
- reworking of the e820 code: separate in-kernel and boot-ABI data
structures and apply a whole range of cleanups to the kernel side.
No change in functionality.
- enable KASLR by default: it's used by all major distros and it's
out of the experimental stage as well.
- ... misc fixes and cleanups"
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (63 commits)
x86/KASLR: Fix kexec kernel boot crash when KASLR randomization fails
x86/reboot: Turn off KVM when halting a CPU
x86/boot: Fix BSS corruption/overwrite bug in early x86 kernel startup
x86: Enable KASLR by default
boot/param: Move next_arg() function to lib/cmdline.c for later reuse
x86/boot: Fix Sparse warning by including required header file
x86/boot/64: Rename start_cpu()
x86/xen: Update e820 table handling to the new core x86 E820 code
x86/boot: Fix pr_debug() API braindamage
xen, x86/headers: Add <linux/device.h> dependency to <asm/xen/page.h>
x86/boot/e820: Simplify e820__update_table()
x86/boot/e820: Separate the E820 ABI structures from the in-kernel structures
x86/boot/e820: Fix and clean up e820_type switch() statements
x86/boot/e820: Rename the remaining E820 APIs to the e820__*() prefix
x86/boot/e820: Remove unnecessary #include's
x86/boot/e820: Rename e820_mark_nosave_regions() to e820__register_nosave_regions()
x86/boot/e820: Rename e820_reserve_resources*() to e820__reserve_resources*()
x86/boot/e820: Use bool in query APIs
x86/boot/e820: Document e820__reserve_setup_data()
x86/boot/e820: Clean up __e820__update_table() et al
...
Pull RAS updates from Ingo Molnar:
"The main changes in this cycle were:
- add the 'Corrected Errors Collector' kernel feature which collect
and monitor correctable errors statistics and will preemptively
(soft-)offline physical pages that have a suspiciously high error
count.
- handle MCE errors during kexec() more gracefully
- factor out and deprecate the /dev/mcelog driver
- ... plus misc fixes and cleanpus"
* 'ras-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Check MCi_STATUS[MISCV] for usable addr on Intel only
ACPI/APEI: Use setup_deferrable_timer()
x86/mce: Update notifier priority check
x86/mce: Enable PPIN for Knights Landing/Mill
x86/mce: Do not register notifiers with invalid prio
x86/mce: Factor out and deprecate the /dev/mcelog driver
RAS: Add a Corrected Errors Collector
x86/mce: Rename mce_log to mce_log_buffer
x86/mce: Rename mce_log()'s argument
x86/mce: Init some CPU features early
x86/mce: Handle broadcasted MCE gracefully with kexec
Pull perf updates from Ingo Molnar:
"The main changes in this cycle were:
Kernel side changes:
- Kprobes and uprobes changes:
- Make their trampolines read-only while they are used
- Make UPROBES_EVENTS default-y which is the distro practice
- Apply misc fixes and robustization to probe point insertion.
- add support for AMD IOMMU events
- extend hw events on Intel Goldmont CPUs
- ... plus misc fixes and updates.
Tooling side changes:
- support s390 jump instructions in perf annotate (Christian
Borntraeger)
- vendor hardware events updates (Andi Kleen)
- add argument support for SDT events in powerpc (Ravi Bangoria)
- beautify the statx syscall arguments in 'perf trace' (Arnaldo
Carvalho de Melo)
- handle inline functions in callchains (Jin Yao)
- enable sorting by srcline as key (Milian Wolff)
- add 'brstackinsn' field in 'perf script' to reuse the x86
instruction decoder used in the Intel PT code to study hot paths to
samples (Andi Kleen)
- add PERF_RECORD_NAMESPACES so that the kernel can record
information required to associate samples to namespaces, helping in
container problem characterization. (Hari Bathini)
- allow sorting by symbol_size in 'perf report' and 'perf top'
(Charles Baylis)
- in perf stat, make system wide (-a) the default option if no target
was specified and one of following conditions is met:
- no workload specified (current behaviour)
- a workload is specified but all requested events are system wide
ones, like uncore ones. (Jiri Olsa)
- ... plus lots of other updates, enhancements, cleanups and fixes"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (235 commits)
perf tools: Fix the code to strip command name
tools arch x86: Sync cpufeatures.h
tools arch: Sync arch/x86/lib/memcpy_64.S with the kernel
tools: Update asm-generic/mman-common.h copy from the kernel
perf tools: Use just forward declarations for struct thread where possible
perf tools: Add the right header to obtain PERF_ALIGN()
perf tools: Remove poll.h and wait.h from util.h
perf tools: Remove string.h, unistd.h and sys/stat.h from util.h
perf tools: Remove stale prototypes from builtin.h
perf tools: Remove string.h from util.h
perf tools: Remove sys/ioctl.h from util.h
perf tools: Remove a few more needless includes from util.h
perf tools: Include sys/param.h where needed
perf callchain: Move callchain specific routines from util.[ch]
perf tools: Add compress.h for the *_decompress_to_file() headers
perf mem: Fix display of data source snoop indication
perf debug: Move dump_stack() and sighandler_dump_stack() to debug.h
perf kvm: Make function only used by 'perf kvm' static
perf tools: Move timestamp routines from util.h to time-utils.h
perf tools: Move units conversion/formatting routines to separate object
...
Pul x86/process updates from Ingo Molnar:
"The main change in this cycle was to add the ARCH_[GET|SET]_CPUID
prctl() ABI extension to control the availability of the CPUID
instruction, analogously to the existing PR_GET|SET_TSC ABI that
controls RDTSC.
Motivation: the 'rr' user-space record-and-replay execution debugger
would like to trap and emulate the CPUID instruction - which
instruction is normally unprivileged.
Trapping CPUID is possible on IvyBridge and later Intel CPUs - expose
this hardware capability"
* 'x86-process-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/syscalls/32: Ignore arch_prctl for other architectures
um/arch_prctl: Fix fallout from x86 arch_prctl() rework
x86/arch_prctl: Add ARCH_[GET|SET]_CPUID
x86/cpufeature: Detect CPUID faulting support
x86/syscalls/32: Wire up arch_prctl on x86-32
x86/arch_prctl: Add do_arch_prctl_common()
x86/arch_prctl/64: Rename do_arch_prctl() to do_arch_prctl_64()
x86/arch_prctl/64: Use SYSCALL_DEFINE2 to define sys_arch_prctl()
x86/arch_prctl: Rename 'code' argument to 'option'
x86/msr: Rename MISC_FEATURE_ENABLES to MISC_FEATURES_ENABLES
x86/process: Optimize TIF_NOTSC switch
x86/process: Correct and optimize TIF_BLOCKSTEP switch
x86/process: Optimize TIF checks in __switch_to_xtra()
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- a big round of FUTEX_UNLOCK_PI improvements, fixes, cleanups and
general restructuring
- lockdep updates such as new checks for lock_downgrade()
- introduce the new atomic_try_cmpxchg() locking API and use it to
optimize refcount code generation
- ... plus misc fixes, updates and cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (38 commits)
MAINTAINERS: Add FUTEX SUBSYSTEM
futex: Clarify mark_wake_futex memory barrier usage
futex: Fix small (and harmless looking) inconsistencies
futex: Avoid freeing an active timer
rtmutex: Plug preempt count leak in rt_mutex_futex_unlock()
rtmutex: Fix more prio comparisons
rtmutex: Fix PI chain order integrity
sched,tracing: Update trace_sched_pi_setprio()
sched/rtmutex: Refactor rt_mutex_setprio()
rtmutex: Clean up
sched/deadline/rtmutex: Dont miss the dl_runtime/dl_period update
sched/rtmutex/deadline: Fix a PI crash for deadline tasks
rtmutex: Deboost before waking up the top waiter
locking/ww-mutex: Limit stress test to 2 seconds
locking/atomic: Fix atomic_try_cmpxchg() semantics
lockdep: Fix per-cpu static objects
futex: Drop hb->lock before enqueueing on the rtmutex
futex: Futex_unlock_pi() determinism
futex: Rework futex_lock_pi() to use rt_mutex_*_proxy_lock()
futex,rt_mutex: Restructure rt_mutex_finish_proxy_lock()
...
Pull EFI updates from Ingo Molnar:
"The main changes in this cycle were:
- move BGRT handling to drivers/acpi so it can be shared between x86
and ARM
- bring the EFI stub's initrd and FDT allocation logic in line with
the latest changes to the arm64 boot protocol
- improvements and fixes to the EFI stub's command line parsing
routines
- randomize the virtual mapping of the UEFI runtime services on
ARM/arm64
- ... and other misc enhancements, cleanups and fixes"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/libstub/arm: Don't use TASK_SIZE when randomizing the RT space
ef/libstub/arm/arm64: Randomize the base of the UEFI rt services region
efi/libstub/arm/arm64: Disable debug prints on 'quiet' cmdline arg
efi/libstub: Unify command line param parsing
efi/libstub: Fix harmless command line parsing bug
efi/arm32-stub: Allow boot-time allocations in the vmlinux region
x86/efi: Clean up a minor mistake in comment
efi/pstore: Return error code (if any) from efi_pstore_write()
efi/bgrt: Enable ACPI BGRT handling on arm64
x86/efi/bgrt: Move efi-bgrt handling out of arch/x86
efi/arm-stub: Round up FDT allocation to mapping size
efi/arm-stub: Correct FDT and initrd allocation rules for arm64
Pull timer updates from Thomas Gleixner:
"The timer departement delivers:
- more year 2038 rework
- a massive rework of the arm achitected timer
- preparatory patches to allow NTP correction of clock event devices
to avoid early expiry
- the usual pile of fixes and enhancements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (91 commits)
timer/sysclt: Restrict timer migration sysctl values to 0 and 1
arm64/arch_timer: Mark errata handlers as __maybe_unused
Clocksource/mips-gic: Remove redundant non devicetree init
MIPS/Malta: Probe gic-timer via devicetree
clocksource: Use GENMASK_ULL in definition of CLOCKSOURCE_MASK
acpi/arm64: Add SBSA Generic Watchdog support in GTDT driver
clocksource: arm_arch_timer: add GTDT support for memory-mapped timer
acpi/arm64: Add memory-mapped timer support in GTDT driver
clocksource: arm_arch_timer: simplify ACPI support code.
acpi/arm64: Add GTDT table parse driver
clocksource: arm_arch_timer: split MMIO timer probing.
clocksource: arm_arch_timer: add structs to describe MMIO timer
clocksource: arm_arch_timer: move arch_timer_needs_of_probing into DT init call
clocksource: arm_arch_timer: refactor arch_timer_needs_probing
clocksource: arm_arch_timer: split dt-only rate handling
x86/uv/time: Set ->min_delta_ticks and ->max_delta_ticks
unicore32/time: Set ->min_delta_ticks and ->max_delta_ticks
um/time: Set ->min_delta_ticks and ->max_delta_ticks
tile/time: Set ->min_delta_ticks and ->max_delta_ticks
score/time: Set ->min_delta_ticks and ->max_delta_ticks
...
Pull irq updates from Thomas Gleixner:
"Nothing exciting from the irq side for this merge window:
- a new driver for a Mediatek SoC
- ACPI support for ARM GICV3
- support for shared nested interrupts
- the usual pile of fixes and updates all over te place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
irqchip/mbigen: Fix return value check in mbigen_device_probe()
irqchip/mips-gic: Replace static map with dynamic
irqchip/mips-gic: Remove device IRQ domain
irqchip/mips-gic: Separate IPI reservation & usage tracking
genirq: Use irqd_get_trigger_type to compare the trigger type for shared IRQs
genirq: Use cpumask_available() for check of cpumask variable
cpumask: Add helper cpumask_available()
irqchip/irq-imx-gpcv2: Clear OF_POPULATED flag
irqchip/atmel-aic5: Handle suspend to RAM
irqchip: Add Mediatek mtk-cirq driver
dt-bindings: mtk-cirq: Add binding document
irqchip/gic-v3-its: Add IORT hook for platform MSI support
irqchip/mbigen: Add ACPI support
irqchip/mbigen: Introduce mbigen_of_create_domain()
irqchip/mbigen: Drop module owner
platform-msi: Make platform_msi_create_device_domain() ACPI aware
irqchip/gicv3-its: platform-msi: Scan MADT to create platform msi domain
irqchip/gicv3-its: platform-msi: Refactor its_pmsi_init() to prepare for ACPI
irqchip/gicv3-its: platform-msi: Refactor its_pmsi_prepare()
irqchip/gic-v3-its: Keep the include header files in alphabetic order
...
This untangles the DM_MAPIO_* values returned from ->clone_and_map_rq
from the error codes used by the block layer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Instead of returning either a DM_ENDIO_* constant or an error code, add
a new DM_ENDIO_DONE value that means keep errno as is. This allows us
to easily keep the existing error code in case where we can't push back,
and it also preparares for the new block level status codes with strict
type checking.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Pull uaccess unification updates from Al Viro:
"This is the uaccess unification pile. It's _not_ the end of uaccess
work, but the next batch of that will go into the next cycle. This one
mostly takes copy_from_user() and friends out of arch/* and gets the
zero-padding behaviour in sync for all architectures.
Dealing with the nocache/writethrough mess is for the next cycle;
fortunately, that's x86-only. Same for cleanups in iov_iter.c (I am
sold on access_ok() in there, BTW; just not in this pile), same for
reducing __copy_... callsites, strn*... stuff, etc. - there will be a
pile about as large as this one in the next merge window.
This one sat in -next for weeks. -3KLoC"
* 'work.uaccess' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (96 commits)
HAVE_ARCH_HARDENED_USERCOPY is unconditional now
CONFIG_ARCH_HAS_RAW_COPY_USER is unconditional now
m32r: switch to RAW_COPY_USER
hexagon: switch to RAW_COPY_USER
microblaze: switch to RAW_COPY_USER
get rid of padding, switch to RAW_COPY_USER
ia64: get rid of copy_in_user()
ia64: sanitize __access_ok()
ia64: get rid of 'segment' argument of __do_{get,put}_user()
ia64: get rid of 'segment' argument of __{get,put}_user_check()
ia64: add extable.h
powerpc: get rid of zeroing, switch to RAW_COPY_USER
esas2r: don't open-code memdup_user()
alpha: fix stack smashing in old_adjtimex(2)
don't open-code kernel_setsockopt()
mips: switch to RAW_COPY_USER
mips: get rid of tail-zeroing in primitives
mips: make copy_from_user() zero tail explicitly
mips: clean and reorder the forest of macros...
mips: consolidate __invoke_... wrappers
...
Pull generic device properties framework updates from Rafael Wysocki:
"These add support for the ports and endpoints concepts, based on the
existing DT support for them, to the generic device properties
framework and update the ACPI _DSD properties code to recognize ports
and endpoints accordingly.
Specifics:
- Extend the ACPI _DSD properties code and the generic device
properties framework to support the concept of remote endponts
(Mika Westerberg, Sakari Ailus).
- Document the support for ports and endpoints in _DSD properties and
extend the generic device properties framework to make it more
suitable for the handling of ports and endpoints (Sakari Ailus)"
* tag 'devprop-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
device property: Read strings using string array reading functions
device property: fwnode_property_read_string_array() returns nr of strings
device property: Fix reading pset strings using array access functions
device property: fwnode_property_read_string_array() may return -EILSEQ
ACPI / DSD: Document references, ports and endpoints
device property: Add fwnode_get_next_parent()
device property: Add support for fwnode endpoints
device property: Make dev_fwnode() public
of: Add of_fwnode_handle() to convert device nodes to fwnode_handle
device property: Add fwnode_handle_get()
device property: Add support for remote endpoints
ACPI / property: Add support for remote endpoints
device property: Add fwnode_get_named_child_node()
ACPI / property: Add fwnode_get_next_child_node()
device property: Add fwnode_get_parent()
ACPI / property: Add possiblity to retrieve parent firmware node
Pull ACPI updates from Rafael Wysocki:
"These are some device enumeration code changes, updates of the AC and
battery drivers to help them avoid attaching to devices that cannot be
handled by them, new operation region driver for the Intel CHT Whiskey
Cove PMIC, new sysfs entries for CPPC performance capabilities, a new
_REV quirk blacklist entry and a couple of assorted minor fixes and
cleanups.
Specifics:
- Update the core device enumeration code to make it more internally
consistent and robust and drop the force_remove sysfs attribute
that could be used to tell it to ignore errors on device
hot-removal which was dangerous in general and no real and still
relevant use cases for it could be found (Rafael Wysocki, Michal
Hocko).
- Make the core device enumeration code use _PXM to associate
platform devices created by it with specific NUMA nodes (Shanker
Donthineni).
- Extend the CPPC library by adding more sysfs entries for
performance capabilities to it and making it use the lowest
nonlinear performance parameter (Prashanth Prakash).
- Make the CPU online more consistent with CPU initialization in the
ACPI processor driver (Prashanth Prakash).
- Update the AC and battery drivers to help them avoid attaching to
devices that cannot be handled by them and update the
axp288_charger power supply driver to work correctly on ACPI
systems without the INT3496 device (Hans de Goede).
- Add an ACPI operation region driver for the Intel CHT Whiskey Cove
PMIC and update the xpower operation region driver to work without
IIO which isn't really necessary for it to work (Hans de Goede).
- Add a new entry for Dell Inspiron 7537 to the _REV quirk blacklist
(Kai Heng Feng).
- Make the code in the ACPI video driver easier to follow by adding
symbols and comments to it (Dmitry Frank).
- Update ACPI documentation and drop a function that has no users
from the tables-handling code (Cao jin, Baoquan He)"
* tag 'acpi-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PMIC: Stop xpower OPRegion handler relying on IIO
ACPI / PMIC: Add opregion driver for Intel CHT Whiskey Cove PMIC
ACPI / scan: Avoid enumerating devices more than once
ACPI / scan: Apply default enumeration to devices with ACPI drivers
power: supply: axp288_charger: Only wait for INT3496 device if present
ACPI / AC: Add a blacklist with PMIC ACPI HIDs with a native charger driver
ACPI / battery: Add a blacklist with PMIC ACPI HIDs with a native battery driver
ACPI / battery: Fix acpi_battery_exit on acpi_battery_init_async errors
ACPI / utils: Add new acpi_dev_present helper
ACPI / video: add comments about subtle cases
ACPI / video: get rid of magic numbers and use enum instead
ACPI / doc: linuxized-acpica.txt: fix typos
ACPI / blacklist: add _REV quirk for Dell Inspiron 7537
ACPI / tables: Drop acpi_parse_entries() which is not used
ACPI / CPPC: add sysfs entries for CPPC perf capabilities
ACPI / CPPC: Read lowest nonlinear perf in cppc_get_perf_caps()
ACPI / platform: Update platform device NUMA node based on _PXM method
ACPI / Processor: Drop setup_max_cpus check from acpi_processor_add()
ACPI / scan: Drop support for force_remove
Pull power management updates from Rafael Wysocki:
"This time the majority of changes go to the cpufreq subsystem (and to
the intel_pstate driver in particular) and there are some updates in
the generic power domains framework, cpuidle, tools and a couple of
other places.
One thing worth mentioning is that the intel_pstate's sysfs interface
has been reworked to be more consistent with the general expectations
of the cpufreq core and less confusing, hopefully for the better.
Also, we have a new cpufreq driver for Tegra186 and new hardware
support in intel_pstata and the Mediatek cpufreq driver.
Apart from that, the AnalyzeSuspend utility for system suspend
profiling gets a companion called AnalyzeBoot for the analogous
profiling of system boot and they both go into one place under
tools/power/pm-graph/.
The rest is mostly fixes, cleanups and code reorganization.
Specifics:
- Rework the intel_pstate driver's sysfs interface to make it more
straightforward and more intuitive (Rafael Wysocki).
- Make intel_pstate support all processors which advertise HWP
(hardware-managed P-states) to the kernel in all operation modes
and make it use the load-based P-state selection algorithm on a
wider range of systems in the active mode (Rafael Wysocki).
- Add cpufreq driver for Tegra186 (Mikko Perttunen).
- Add support for Gemini Lake SoCs to intel_pstate (David Box).
- Add support for MT8176 and MT817x to the Mediatek cpufreq driver
and clean up that driver a bit (Daniel Kurtz).
- Clean up intel_pstate and optimize it slightly (Rafael Wysocki).
- Update the schedutil cpufreq governor, mostly to fix a couple of
issues with it related to specific workloads, and rework its sysfs
tunable and initialization a bit (Rafael Wysocki, Viresh Kumar).
- Fix minor issues in the imx6q, dbx500 and qoriq cpufreq drivers
(Christophe Jaillet, Irina Tirdea, Leonard Crestez, Viresh Kumar,
YuanTian Tang).
- Add file patterns for cpufreq DT bindings to MAINTAINERS (Geert
Uytterhoeven).
- Add support for "always on" power domains to the genpd (generic
power domains) framework and clean up that code somewhat (Ulf
Hansson, Lina Iyer, Viresh Kumar).
- Fix minor issues in the powernv cpuidle driver and clean it up
(Anton Blanchard, Gautham Shenoy).
- Move the AnalyzeSuspend utility under tools/power/pm-graph/ and add
an analogous boot-profiling utility called AnalyzeBoot to it (Todd
Brandt).
- Add rk3328 support to the rockchip-io AVS (Adaptive Voltage
Scaling) driver (David Wu).
- Fix minor issues in the cpuidle core, the intel_pstate_tracer
utility, the devfreq framework and the PM core documentation
(Chanwoo Choi, Doug Smythies, Johan Hovold, Marcin Nowakowski)"
* tag 'pm-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (56 commits)
PM / runtime: Document autosuspend-helper side effects
PM / runtime: Fix autosuspend documentation
tools: power: pm-graph: Package makefile and man pages
tools: power: pm-graph: AnalyzeBoot v2.0
tools: power: pm-graph: AnalyzeSuspend v4.6
cpufreq: Add Tegra186 cpufreq driver
cpufreq: imx6q: Fix error handling code
cpufreq: imx6q: Set max suspend_freq to avoid changes during suspend
cpufreq: imx6q: Fix handling EPROBE_DEFER from regulator
cpuidle: powernv: Avoid a branch in the core snooze_loop() loop
cpuidle: powernv: Don't continually set thread priority in snooze_loop()
cpuidle: powernv: Don't bounce between low and very low thread priority
cpuidle: cpuidle-cps: remove unused variable
tools/power/x86/intel_pstate_tracer: Adjust directory ownership
cpufreq: schedutil: Use policy-dependent transition delays
cpufreq: schedutil: Reduce frequencies slower
PM / devfreq: Move struct devfreq_governor to devfreq directory
PM / Domains: Ignore domain-idle-states that are not compatible
cpufreq: intel_pstate: Add support for Gemini Lake
powernv-cpuidle: Validate DT property array size
...
Pull cgroup updates from Tejun Heo:
"Nothing major. Two notable fixes are Li's second stab at fixing the
long-standing race condition in the mount path and suppression of
spurious warning from cgroup_get(). All other changes are trivial"
* 'for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: mark cgroup_get() with __maybe_unused
cgroup: avoid attaching a cgroup root to two different superblocks, take 2
cgroup: fix spurious warnings on cgroup_is_dead() from cgroup_sk_alloc()
cgroup: move cgroup_subsys_state parent field for cache locality
cpuset: Remove cpuset_update_active_cpus()'s parameter.
cgroup: switch to BUG_ON()
cgroup: drop duplicate header nsproxy.h
kernel: convert css_set.refcount from atomic_t to refcount_t
kernel: convert cgroup_namespace.count from atomic_t to refcount_t
From Boris:
"""
This pull request contains:
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
"""
Pull libata updates from Tejun Heo:
"The biggest core change is removal of SCT WRITE SAME support, which
never worked properly.
Other than that, trivial updates in core code and specific embedded
driver updates"
* 'for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: remove SCT WRITE SAME support
libata: reject passthrough WRITE SAME requests
dt-bindings: ata: add DT bindings for ahci-dm816 SATA controller
ata: ahci: add support for DaVinci DM816 SATA controller
pata: remove the at91 driver
libata: make ata_sg_clean static over again
libata: use setup_deferrable_timer
ata: allow subsystem to be used on m32r and s390 archs
Delete redundant return value check of platform_get_resource()
ata: constify of_device_id structures
By using smaller datatypes this (rather large) struct shrinks considerably
(80 -> 48 bytes on x86_64).
As this is embedded in other structs, this also rerduces size of several
others, e.g. cls_fl_head or nft_hash.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull LED updates from Jacek Anaszewski:
"New drivers:
- add LED support for MT6323 PMIC
- add LED support for Motorola CPCAP PMIC
New features and improvements:
- add LED trigger for all CPUs aggregated which is useful on tiny
boards with more CPU cores than LED pins
- add OF variants of LED registering functions as a preparation for
adding generic support for Device Tree parsing
- dell-led improvements and cleanups, followed by moving it to the
x86 platform driver subsystem which is a more appropriate place for
it
- extend pca9532 Device Tree support by adding the LEDs
'default-state' property
- extend pca963x Device Tree support by adding nxp,inverted-out
property for inverting the polarity of the output
- remove ACPI support for lp3952 since it relied on a non-official
ACPI IDs"
* tag 'leds_for_4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: pca9532: Extend pca9532 device tree support
leds: cpcap: new driver
mfd: cpcap: Add missing include dependencies
leds: lp3952: Use 'if (ret)' pattern
leds: lp3952: Remove ACPI support for lp3952
leds: mt6323: Fix an off by one bug in probe
dt-bindings: leds: Add document bindings for leds-mt6323
leds: Add LED support for MT6323 PMIC
leds: gpio: use OF variant of LED registering function
leds: core: add OF variants of LED registering functions
platform/x86: dell-wmi-led: fix coding style issues
dell-led: move driver to drivers/platform/x86/dell-wmi-led.c
dell-led: remove code related to mic mute LED
platform/x86: dell-laptop: import dell_micmute_led_set() from drivers/leds/dell-led.c
ALSA: hda - rename dell_led_set_func to dell_micmute_led_set_func
ALSA: hda - use dell_micmute_led_set() instead of dell_app_wmi_led_set()
dell-led: remove GUID check from dell_micmute_led_set()
leds/trigger/cpu: Add LED trigger for all CPUs aggregated
Pull mailbox updates from Jassi Brar:
- new driver for Broadcom FlexRM controller
- constify data structures of callback functions in some drivers
- a few bug fixes uncovered by multi-threaded use of mailbox channels
in blocking mode
* 'mailbox-for-next' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: handle empty message in tx_tick
mailbox: skip complete wait event if timer expired
mailbox: always wait in mbox_send_message for blocking Tx mode
mailbox: Remove depends on COMPILE_TEST for BCM_FLEXRM_MBOX
mailbox: check ->last_tx_done for NULL in case of timer-based polling
dt-bindings: Add DT bindings info for FlexRM ring manager
mailbox: Add driver for Broadcom FlexRM ring manager
dt-bindings: mailbox: Update doc with NSP PDC/mailbox support
mailbox: bcm-pdc: Add Northstar Plus support to PDC driver
mailbox: constify mbox_chan_ops structures
Add port_xmit_wait to the error counters read by mlx5_ib_process_mad to
ensure sysfs port counter provides correct value for PortXmitWait.
Otherwise the sysfs port_xmit_wait file always contains zero.
The previous MAD_IFC implementation populated this counter, but it was
removed during the migration to PPCNT for error counters (32-bit only).
Signed-off-by: Tim Wright <tim@binbash.co.uk>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pull hwmon updates from Guenter Roeck:
- removed twl4030-madc driver
- added ASPEED PWM/fan driver
- various minor improvements and fixes in several drivers
* tag 'hwmon-for-linus-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (36 commits)
hwmon: (twl4030-madc) drop driver
hwmon: (tmp103) Use SIMPLE_DEV_PM_OPS helper macro
hwmon: (adt7475) set start bit in probe
hwmon: (ina209) Handled signed registers
hwmon: (lm87) Add OF device ID table
hwmon: (lm87) Remove unused I2C devices driver_data
drivers: hwmon: Support for ASPEED PWM/Fan tach
Documentation: dt-bindings: Document bindings for ASPEED AST2400/AST2500 PWM and Fan tach controller device driver
hwmon: (lm87) Allow channel data to be set from dts file
Documentation: dtb: lm87: Add hwmon binding documentation
hwmon: (ads7828) Accept optional parameters from device tree
hwmon: (dell-smm) Add Dell XPS 15 9560 into DMI list
hwmon: Constify str parameter of hwmon_ops->read_string
dt: Add vendor prefix for Sensirion
hwmon: (tmp421) Add OF device ID table
hwmon: (tmp103) Add OF device ID table
hwmon: (tmp102) Add OF device ID table
hwmon: (stts751) Add OF device ID table
hwmon: (ucd9200) Add OF device ID table
hwmon: (ucd9000) Add OF device ID table
...
Pull EDAC updates from Borislav Petkov:
- an EDAC driver for Cavium ThunderX RAS IP (Sergey Temerkhanov)
- removal of DRAM error reporting through PCI SERR NMI (Borislav
Petkov)
- misc small fixes (Jan Glauber, Thor Thayer)
* tag 'edac_for_4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, ghes: Do not enable it by default
EDAC: Rename report status accessors
EDAC: Delete edac_stub.c
EDAC: Update Kconfig help text
EDAC: Remove EDAC_MM_EDAC
EDAC: Issue tracepoint only when it is defined
ACPI/extlog: Add EDAC dependency
EDAC: Move edac_op_state to edac_mc.c
EDAC: Remove edac_err_assert
EDAC: Get rid of edac_handlers
x86/nmi, EDAC: Get rid of DRAM error reporting thru PCI SERR NMI
EDAC, highbank: Align Makefile directives
EDAC, thunderx: Remove unused code
EDAC, thunderx: Change LMC index calculation
EDAC, altera: Fix peripheral warnings for Cyclone5
EDAC, thunderx: Fix L2C MCI interrupt disable
EDAC, thunderx: Add Cavium ThunderX EDAC driver
Pull block layer updates from Jens Axboe:
- Add BFQ IO scheduler under the new blk-mq scheduling framework. BFQ
was initially a fork of CFQ, but subsequently changed to implement
fairness based on B-WF2Q+, a modified variant of WF2Q. BFQ is meant
to be used on desktop type single drives, providing good fairness.
From Paolo.
- Add Kyber IO scheduler. This is a full multiqueue aware scheduler,
using a scalable token based algorithm that throttles IO based on
live completion IO stats, similary to blk-wbt. From Omar.
- A series from Jan, moving users to separately allocated backing
devices. This continues the work of separating backing device life
times, solving various problems with hot removal.
- A series of updates for lightnvm, mostly from Javier. Includes a
'pblk' target that exposes an open channel SSD as a physical block
device.
- A series of fixes and improvements for nbd from Josef.
- A series from Omar, removing queue sharing between devices on mostly
legacy drivers. This helps us clean up other bits, if we know that a
queue only has a single device backing. This has been overdue for
more than a decade.
- Fixes for the blk-stats, and improvements to unify the stats and user
windows. This both improves blk-wbt, and enables other users to
register a need to receive IO stats for a device. From Omar.
- blk-throttle improvements from Shaohua. This provides a scalable
framework for implementing scalable priotization - particularly for
blk-mq, but applicable to any type of block device. The interface is
marked experimental for now.
- Bucketized IO stats for IO polling from Stephen Bates. This improves
efficiency of polled workloads in the presence of mixed block size
IO.
- A few fixes for opal, from Scott.
- A few pulls for NVMe, including a lot of fixes for NVMe-over-fabrics.
From a variety of folks, mostly Sagi and James Smart.
- A series from Bart, improving our exposed info and capabilities from
the blk-mq debugfs support.
- A series from Christoph, cleaning up how handle WRITE_ZEROES.
- A series from Christoph, cleaning up the block layer handling of how
we track errors in a request. On top of being a nice cleanup, it also
shrinks the size of struct request a bit.
- Removal of mg_disk and hd (sorry Linus) by Christoph. The former was
never used by platforms, and the latter has outlived it's usefulness.
- Various little bug fixes and cleanups from a wide variety of folks.
* 'for-4.12/block' of git://git.kernel.dk/linux-block: (329 commits)
block: hide badblocks attribute by default
blk-mq: unify hctx delay_work and run_work
block: add kblock_mod_delayed_work_on()
blk-mq: unify hctx delayed_run_work and run_work
nbd: fix use after free on module unload
MAINTAINERS: bfq: Add Paolo as maintainer for the BFQ I/O scheduler
blk-mq-sched: alloate reserved tags out of normal pool
mtip32xx: use runtime tag to initialize command header
scsi: Implement blk_mq_ops.show_rq()
blk-mq: Add blk_mq_ops.show_rq()
blk-mq: Show operation, cmd_flags and rq_flags names
blk-mq: Make blk_flags_show() callers append a newline character
blk-mq: Move the "state" debugfs attribute one level down
blk-mq: Unregister debugfs attributes earlier
blk-mq: Only unregister hctxs for which registration succeeded
blk-mq-debugfs: Rename functions for registering and unregistering the mq directory
blk-mq: Let blk_mq_debugfs_register() look up the queue name
blk-mq: Register <dev>/queue/mq after having registered <dev>/queue
ide-pm: always pass 0 error to ide_complete_rq in ide_do_devset
ide-pm: always pass 0 error to __blk_end_request_all
..
mlx5-updates-2017-04-30
Or says:
================
mlx5 neigh update
This series (whose code name is 'neigh update') from Hadar, enhances the
mlx5 TC IP tunnel offloads to deal with changes to tunnel destination
neighbours used in offloaded flows which involved encapsulation.
In order to keep track on the validity state of such neighbours, we register
a netevent notifier callback and act on NEIGH_UPDATE events: if a neighbour
becomes valid, offload the related flows to HW (the other way around when
neigh becomes invalid) and similarly when a neigh mac addresses changes.
Since this traffic is offloaded from the host OS, the neighbour for the IP
tunnel destination can mistakenly become STALE and deleted by the kernel
since its 'used' value wasn't changed. To address that, we proactively
update the neighbour 'used' value every DELAY_PROBE_TIME seconds, using
time stamps generated by the existing driver code for HW flow counters.
We use the DELAY_PROBE_TIME_UPDATE event to adjust the frequency of the updates.
Prior to the core of the series, there's a patch from Saeed that introduces an
extendable vport representor implementation scheme. It provides a separation
between the eswitch to the netdev related aspects of the representors.
We would like to thank Ido Schimmel and Ilya Lesokhin for their coaching && advice
through the long design and review cycles while we struggled to understand and
(hopefully correctly) implement the locking around the different driver flows(..) .
- Or.
=================
Misc Updates:
From Tariq:
Some small performance and trivial code optimization for mlx5 netdev driver
- Optimize poll ICOSQ completion queue
- Use prefetchw when a write is to follow
- Use u8 as ownership type in mlx5e_get_cqe()
From Eran:
- Disable LRO by default on specific setups
From Eli:
- Small cleanup for E-Switch to avoid redundant allocation
Signed-off-by: David S. Miller <davem@davemloft.net>
Output to the RDMA driver whether DPM mode is enabled or disabled in
the HW and if so what is the number of WIDs it supports
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. A large bunch of code cleanups, simplify the conntrack extension
codebase, get rid of the fake conntrack object, speed up netns by
selective synchronize_net() calls. More specifically, they are:
1) Check for ct->status bit instead of using nfct_nat() from IPVS and
Netfilter codebase, patch from Florian Westphal.
2) Use kcalloc() wherever possible in the IPVS code, from Varsha Rao.
3) Simplify FTP IPVS helper module registration path, from Arushi Singhal.
4) Introduce nft_is_base_chain() helper function.
5) Enforce expectation limit from userspace conntrack helper,
from Gao Feng.
6) Add nf_ct_remove_expect() helper function, from Gao Feng.
7) NAT mangle helper function return boolean, from Gao Feng.
8) ctnetlink_alloc_expect() should only work for conntrack with
helpers, from Gao Feng.
9) Add nfnl_msg_type() helper function to nfnetlink to build the
netlink message type.
10) Get rid of unnecessary cast on void, from simran singhal.
11) Use seq_puts()/seq_putc() instead of seq_printf() where possible,
also from simran singhal.
12) Use list_prev_entry() from nf_tables, from simran signhal.
13) Remove unnecessary & on pointer function in the Netfilter and IPVS
code.
14) Remove obsolete comment on set of rules per CPU in ip6_tables,
no longer true. From Arushi Singhal.
15) Remove duplicated nf_conntrack_l4proto_udplite4, from Gao Feng.
16) Remove unnecessary nested rcu_read_lock() in
__nf_nat_decode_session(). Code running from hooks are already
guaranteed to run under RCU read side.
17) Remove deadcode in nf_tables_getobj(), from Aaron Conole.
18) Remove double assignment in nf_ct_l4proto_pernet_unregister_one(),
also from Aaron.
19) Get rid of unsed __ip_set_get_netlink(), from Aaron Conole.
20) Don't propagate NF_DROP error to userspace via ctnetlink in
__nf_nat_alloc_null_binding() function, from Gao Feng.
21) Revisit nf_ct_deliver_cached_events() to remove unnecessary checks,
from Gao Feng.
22) Kill the fake untracked conntrack objects, use ctinfo instead to
annotate a conntrack object is untracked, from Florian Westphal.
23) Remove nf_ct_is_untracked(), now obsolete since we have no
conntrack template anymore, from Florian.
24) Add event mask support to nft_ct, also from Florian.
25) Move nf_conn_help structure to
include/net/netfilter/nf_conntrack_helper.h.
26) Add a fixed 32 bytes scratchpad area for conntrack helpers.
Thus, we don't deal with variable conntrack extensions anymore.
Make sure userspace conntrack helper doesn't go over that size.
Remove variable size ct extension infrastructure now this code
got no more clients. From Florian Westphal.
27) Restore offset and length of nf_ct_ext structure to 8 bytes now
that wraparound is not possible any longer, also from Florian.
28) Allow to get rid of unassured flows under stress in conntrack,
this applies to DCCP, SCTP and TCP protocols, from Florian.
29) Shrink size of nf_conntrack_ecache structure, from Florian.
30) Use TCP_MAX_WSCALE instead of hardcoded 14 in TCP tracker,
from Gao Feng.
31) Register SYNPROXY hooks on demand, from Florian Westphal.
32) Use pernet hook whenever possible, instead of global hook
registration, from Florian Westphal.
33) Pass hook structure to ebt_register_table() to consolidate some
infrastructure code, from Florian Westphal.
34) Use consume_skb() and return NF_STOLEN, instead of NF_DROP in the
SYNPROXY code, to make sure device stats are not fooled, patch
from Gao Feng.
35) Remove NF_CT_EXT_F_PREALLOC this kills quite some code that we
don't need anymore if we just select a fixed size instead of
expensive runtime time calculation of this. From Florian.
36) Constify nf_ct_extend_register() and nf_ct_extend_unregister(),
from Florian.
37) Simplify nf_ct_ext_add(), this kills nf_ct_ext_create(), from
Florian.
38) Attach NAT extension on-demand from masquerade and pptp helper
path, from Florian.
39) Get rid of useless ip_vs_set_state_timeout(), from Aaron Conole.
40) Speed up netns by selective calls of synchronize_net(), from
Florian Westphal.
41) Silence stack size warning gcc in 32-bit arch in snmp helper,
from Florian.
42) Inconditionally call nf_ct_ext_destroy(), even if we have no
extensions, to deal with the NF_NAT_MANIP_SRC case. Patch from
Liping Zhang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers usually have a number of restrictions for running XDP
- most common being buffer sizes, LRO and number of rings.
Even though some drivers try to be helpful and print error
messages experience shows that users don't often consult
kernel logs on netlink errors. Try to use the new extended
ack mechanism to carry the message back to user space.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
