Allwinner H3 changes for 4.13
This tag is about bringing the EMAC support to the H3 boards.
* tag 'sunxi-dt-h3-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: sun8i: h3: Enable EMAC with external PHY on Orange Pi Plus 2E
arm: sun8i: orangepi-zero: Enable dwmac-sun8i
ARM: sun8i: bananapi-m2-plus: Enable dwmac-sun8i
ARM: sun8i: orangepi-plus: Enable dwmac-sun8i
arm: sun8i: nanopi-neo: Enable dwmac-sun8i
arm: sun8i: orangepi-pc-plus: Set EMAC activity LEDs to active high
arm: sun8i: orangepi-2: Enable dwmac-sun8i
arm: sun8i: orangepi-one: Enable dwmac-sun8i
arm: sun8i: orangepi-pc: Enable dwmac-sun8i
arm: sun8i: sunxi-h3-h5: add dwmac-sun8i ethernet driver
arm: sun8i: sunxi-h3-h5: Add dt node for the syscon control module
ARM: sunxi: h3-h5: Convert R_CCU raw numbers to macros
Signed-off-by: Olof Johansson <olof@lixom.net>
The dwmac-sun8i hardware is present on the Orange PI Zero.
It uses the internal PHY.
This patch create the needed emac node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add node for SPI NOR flash on orange-pi-zero board. Disable this node
by default and leave it to users to enable it if their board has
SPI NOR flash chip populated.
SPI NOR flash was optional in the first production batch in Dec 2016.
In later batches flash chip was pre-populated. However there should
be quite a few boards around which do not have flash chip.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner H3 DT changes for 4.12
H3 patches for 4.12, which are mostly related to reworking the H3 DTSI to
be usable on the arm64 H5 DTSI, that shares almost everything with the H3
but the CPU cores.
We also have some new device addition (USB, mostly) that would conflict
otherwise.
* tag 'sunxi-dt-h3-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: sun8i: h2+: enable USB OTG for Orange Pi Zero board
ARM: sun8i: h3: enable USB OTG on Orange Pi One
ARM: sunxi: h3/h5: add usb_otg and OHCI/EHCI for usbc0 on H3/H5
arm: sun8i: h3: split Allwinner H3 .dtsi
arm: sun8i: h3: correct the GIC compatible in H3 to gic-400
arm: sun8i: h3: drop pinctrl-a10.h inclusion for H3 DTSI
arm: sun8i: h3: drop skeleton.dtsi inclusion in H3 DTSI
Signed-off-by: Olof Johansson <olof@lixom.net>
Orange Pi Zero board features a USB OTG port, which has a ID pin, and
can be used to power up the board. However, even if the board is powered
via +5V pin in GPIO/expansion headers, the VBUS in the OTG port cannot
be powered up, thus it's impossible to use it in host mode with simple
OTG cables.
Add support for it in peripheral mode.
If someone really want to use it in host mode, the mode of PHY can be
switch via sysfs, then use a powered USB OTG cable or powered USB HUB to
power up external USB devices.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All dts files for the sunxi platform have been switched to the generic
pinconf bindings. As a result, the sunxi specific pinctrl macros are
no longer used.
Remove the #include entry with the following command:
sed --follow-symlinks -i -e '/pinctrl\/sun4i-a10.h/D' \
arch/arm/boot/dts/sun?i*.*
arch/arm/boot/dts/sun9i-a80.dtsi was then edited to remove the extra
empty line.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
XR819 seems to need a delay after its reset line to be deasserted,
otherwise it may not respond MMC commands correctly, and fail to
initialize.
Add a 200ms delay in the mmc-pwrseq.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Orange Pi Zero is a board that came with the new Allwinner H2+ SoC and a
SDIO Wi-Fi chip by Allwinner (XR819).
Add a device tree file for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
