The 1588 standard defines one step operation for both Sync and
PDelay_Resp messages. Up until now, hardware with P2P one step has
been rare, and kernel support was lacking. This patch adds support of
the mode in anticipation of new hardware developments.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While PHY time stamping drivers can simply attach their interface
directly to the PHY instance, stand alone drivers require support in
order to manage their services. Non-PHY MII time stamping drivers
have a control interface over another bus like I2C, SPI, UART, or via
a memory mapped peripheral. The controller device will be associated
with one or more time stamping channels, each of which sits snoops in
on a MII bus.
This patch provides a glue layer that will enable time stamping
channels to find their controlling device.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the stack supports time stamping in PHY devices. However,
there are newer, non-PHY devices that can snoop an MII bus and provide
time stamps. In order to support such devices, this patch introduces
a new interface to be used by both PHY and non-PHY devices.
In addition, the one and only user of the old PHY time stamping API is
converted to the new interface.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool layer tests fields of the phy_device in order to determine
whether to invoke the PHY's tsinfo ethtool callback. This patch
replaces the open coded logic with an invocation of the proper
methods.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan layer tests fields of the phy_device in order to determine
whether to invoke the PHY's tsinfo ethtool callback. This patch
replaces the open coded logic with an invocation of the proper
methods.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The supervision frame is L2 frame.
When supervision frame is created, hsr module doesn't set network header.
If tap routine is enabled, dev_queue_xmit_nit() is called and it checks
network_header. If network_header pointer wasn't set(or invalid),
it resets network_header and warns.
In order to avoid unnecessary warning message, resetting network_header
is needed.
Test commands:
ip netns add nst
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link set veth1 netns nst
ip link set veth3 netns nst
ip link set veth0 up
ip link set veth2 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec nst ip link set veth1 up
ip netns exec nst ip link set veth3 up
ip netns exec nst ip link add hsr1 type hsr slave1 veth1 slave2 veth3
ip netns exec nst ip a a 192.168.100.2/24 dev hsr1
ip netns exec nst ip link set hsr1 up
tcpdump -nei veth0
Splat looks like:
[ 175.852292][ C3] protocol 88fb is buggy, dev veth0
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hsr nodes are protected by RCU and there is no write side lock.
But node insertions and deletions could be being operated concurrently.
So write side locking is needed.
Test commands:
ip netns add nst
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link set veth1 netns nst
ip link set veth3 netns nst
ip link set veth0 up
ip link set veth2 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec nst ip link set veth1 up
ip netns exec nst ip link set veth3 up
ip netns exec nst ip link add hsr1 type hsr slave1 veth1 slave2 veth3
ip netns exec nst ip a a 192.168.100.2/24 dev hsr1
ip netns exec nst ip link set hsr1 up
for i in {0..9}
do
for j in {0..9}
do
for k in {0..9}
do
for l in {0..9}
do
arping 192.168.100.2 -I hsr0 -s 00:01:3$i:4$j:5$k:6$l -c1 &
done
done
done
done
Splat looks like:
[ 236.066091][ T3286] list_add corruption. next->prev should be prev (ffff8880a5940300), but was ffff8880a5940d0.
[ 236.069617][ T3286] ------------[ cut here ]------------
[ 236.070545][ T3286] kernel BUG at lib/list_debug.c:25!
[ 236.071391][ T3286] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 236.072343][ T3286] CPU: 0 PID: 3286 Comm: arping Tainted: G W 5.5.0-rc1+ #209
[ 236.073463][ T3286] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 236.074695][ T3286] RIP: 0010:__list_add_valid+0x74/0xd0
[ 236.075499][ T3286] Code: 48 39 da 75 27 48 39 f5 74 36 48 39 dd 74 31 48 83 c4 08 b8 01 00 00 00 5b 5d c3 48 b
[ 236.078277][ T3286] RSP: 0018:ffff8880aaa97648 EFLAGS: 00010286
[ 236.086991][ T3286] RAX: 0000000000000075 RBX: ffff8880d4624c20 RCX: 0000000000000000
[ 236.088000][ T3286] RDX: 0000000000000075 RSI: 0000000000000008 RDI: ffffed1015552ebf
[ 236.098897][ T3286] RBP: ffff88809b53d200 R08: ffffed101b3c04f9 R09: ffffed101b3c04f9
[ 236.099960][ T3286] R10: 00000000308769a1 R11: ffffed101b3c04f8 R12: ffff8880d4624c28
[ 236.100974][ T3286] R13: ffff8880d4624c20 R14: 0000000040310100 R15: ffff8880ce17ee02
[ 236.138967][ T3286] FS: 00007f23479fa680(0000) GS:ffff8880d9c00000(0000) knlGS:0000000000000000
[ 236.144852][ T3286] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 236.145720][ T3286] CR2: 00007f4a14bab210 CR3: 00000000a61c6001 CR4: 00000000000606f0
[ 236.146776][ T3286] Call Trace:
[ 236.147222][ T3286] hsr_add_node+0x314/0x490 [hsr]
[ 236.153633][ T3286] hsr_forward_skb+0x2b6/0x1bc0 [hsr]
[ 236.154362][ T3286] ? rcu_read_lock_sched_held+0x90/0xc0
[ 236.155091][ T3286] ? rcu_read_lock_bh_held+0xa0/0xa0
[ 236.156607][ T3286] hsr_dev_xmit+0x70/0xd0 [hsr]
[ 236.157254][ T3286] dev_hard_start_xmit+0x160/0x740
[ 236.157941][ T3286] __dev_queue_xmit+0x1961/0x2e10
[ 236.158565][ T3286] ? netdev_core_pick_tx+0x2e0/0x2e0
[ ... ]
Reported-by: syzbot+3924327f9ad5f4d2b343@syzkaller.appspotmail.com
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hsr interface has own debugfs file, which name is same with interface name.
So, interface name is changed, debugfs file name should be changed too.
Fixes: fc4ecaeebd ("net: hsr: add debugfs support for display node list")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current hsr code, when hsr interface is created, it creates debugfs
directory /sys/kernel/debug/<interface name>.
If there is same directory or file name in there, it fails.
In order to reduce possibility of failure of creation of debugfs,
this patch adds root directory.
Test commands:
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1
Before this patch:
/sys/kernel/debug/hsr0/node_table
After this patch:
/sys/kernel/debug/hsr/hsr0/node_table
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hsr_dev_finalize() is called to create new hsr interface.
There are some wrong error handling codes.
1. wrong checking return value of debugfs_create_{dir/file}.
These function doesn't return NULL. If error occurs in there,
it returns error pointer.
So, it should check error pointer instead of NULL.
2. It doesn't unregister interface if it fails to setup hsr interface.
If it fails to initialize hsr interface after register_netdevice(),
it should call unregister_netdevice().
3. Ignore failure of creation of debugfs
If creating of debugfs dir and file is failed, creating hsr interface
will be failed. But debugfs doesn't affect actual logic of hsr module.
So, ignoring this is more correct and this behavior is more general.
Fixes: c5a7591172 ("net/hsr: Use list_head (and rcu) instead of array for slave devices.")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that mlxsw is converted to use the new FIB notifications it is
possible to delete the old ones and use the new replace / append /
delete notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an entire multipath route is deleted, only emit a notification if
it is the first route in the node. Emit a replace notification in case
the last sibling is followed by another route. Otherwise, emit a delete
notification.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the purpose of route offload, when a single route is deleted, it is
only of interest if it is the first route in the node or if it is
sibling to such a route.
In the first case, distinguish between several possibilities:
1. Route is the last route in the node. Emit a delete notification
2. Route is followed by a non-multipath route. Emit a replace
notification for the non-multipath route.
3. Route is followed by a multipath route. Emit a replace notification
for the multipath route.
In the second case, only emit a delete notification to ensure the route
is no longer used as a valid nexthop.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new listener is registered to the FIB notification chain it
receives a dump of all the available routes in the system. Instead, make
sure to only replay the IPv6 routes that are actually used in the data
path and are of any interest to the new listener.
This is done by iterating over all the routing tables in the given
namespace, but from each traversed node only the first route ('leaf') is
notified. Multipath routes are notified in a single notification instead
of one for each nexthop.
Add fib6_rt_dump_tmp() to do that. Later on in the patch set it will be
renamed to fib6_rt_dump() instead of the existing one.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to previous patches, only notify the new multipath
route if it is the first route in the node or if it was appended to such
route.
The type of the notification (replace vs. append) is determined based on
the number of routes added ('nhn') and the number of sibling routes. If
the two do not match, then an append notification should be sent.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the corresponding IPv4 patch, only notify the new route if it
is replacing the currently offloaded one. Meaning, the one pointed to by
'fn->leaf'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib6_add_rt2node() takes care of adding a single route ('struct
fib6_info') to a FIB node. The route in question should only be notified
in case it is added as the first route in the node (lowest metric) or if
it is added as a sibling route to the first route in the node.
The first criterion can be tested by checking if the route is pointed to
by 'fn->leaf'. The second criterion can be tested by checking the new
'notify_sibling_rt' variable that is set when the route is added as a
sibling to the first route in the node.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
Although vti and vti6 are immune to this problem because they are IFF_NOARP
interfaces, as Guillaume pointed. There is still no sense to confirm neighbour
here.
v5: Update commit description.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When do tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
v5: No Change.
v4: Update commit description
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Fixes: 0dec879f63 ("net: use dst_confirm_neigh for UDP, RAW, ICMP, L2TP")
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Tested-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we do ipv6 gre pmtu update, we will also do neigh confirm currently.
This will cause the neigh cache be refreshed and set to REACHABLE before
xmit.
But if the remote mac address changed, e.g. device is deleted and recreated,
we will not able to notice this and still use the old mac address as the neigh
cache is REACHABLE.
Fix this by disable neigh confirm when do pmtu update
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reported-by: Jianlin Shi <jishi@redhat.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTU update code is supposed to be invoked in response to real
networking events that update the PMTU. In IPv6 PMTU update function
__ip6_rt_update_pmtu() we called dst_confirm_neigh() to update neighbor
confirmed time.
But for tunnel code, it will call pmtu before xmit, like:
- tnl_update_pmtu()
- skb_dst_update_pmtu()
- ip6_rt_update_pmtu()
- __ip6_rt_update_pmtu()
- dst_confirm_neigh()
If the tunnel remote dst mac address changed and we still do the neigh
confirm, we will not be able to update neigh cache and ping6 remote
will failed.
So for this ip_tunnel_xmit() case, _EVEN_ if the MTU is changed, we
should not be invoking dst_confirm_neigh() as we have no evidence
of successful two-way communication at this point.
On the other hand it is also important to keep the neigh reachability fresh
for TCP flows, so we cannot remove this dst_confirm_neigh() call.
To fix the issue, we have to add a new bool parameter for dst_ops.update_pmtu
to choose whether we should do neigh update or not. I will add the parameter
in this patch and set all the callers to true to comply with the previous
way, and fix the tunnel code one by one on later patches.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Suggested-by: David Miller <davem@davemloft.net>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing PUSH MPLS action inserts MPLS header between ethernet header
and the IP header. Though this behaviour is fine for L3 VPN where an IP
packet is encapsulated inside a MPLS tunnel, it does not suffice the L2
VPN (l2 tunnelling) requirements. In L2 VPN the MPLS header should
encapsulate the ethernet packet.
The new mpls action ADD_MPLS inserts MPLS header at the start of the
packet or at the start of the l3 header depending on the value of l3 tunnel
flag in the ADD_MPLS arguments.
POP_MPLS action is extended to support ethertype 0x6558.
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rephrased comments section of skb_mpls_pop() to align it with
comments section of skb_mpls_push().
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing skb_mpls_push() implementation always inserts mpls header
after the mac header. L2 VPN use cases requires MPLS header to be
inserted before the ethernet header as the ethernet packet gets tunnelled
inside MPLS header in those cases.
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells says:
====================
rxrpc: Fixes
Here are a couple of bugfixes plus a patch that makes one of the bugfixes
easier:
(1) Move the ping and mutex unlock on a new call from rxrpc_input_packet()
into rxrpc_new_incoming_call(), which it calls. This means the
lock-unlock section is entirely within the latter function. This
simplifies patch (2).
(2) Don't take the call->user_mutex at all in the softirq path. Mutexes
aren't allowed to be taken or released there and a patch was merged
that caused a warning to be emitted every time this happened. Looking
at the code again, it looks like that taking the mutex isn't actually
necessary, as the value of call->state will block access to the call.
(3) Fix the incoming call path to check incoming calls earlier to reject
calls to RPC services for which we don't have a security key of the
appropriate class. This avoids an assertion failure if YFS tries
making a secure call to the kafs cache manager RPC service.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The fix on 951c6db954 fixed the issued reported there but introduced
another. When the allocation fails within sctp_stream_init() it is
okay/necessary to free the genradix. But it is also called when adding
new streams, from sctp_send_add_streams() and
sctp_process_strreset_addstrm_in() and in those situations it cannot
just free the genradix because by then it is a fully operational
association.
The fix here then is to only free the genradix in sctp_stream_init()
and on those other call sites move on with what it already had and let
the subsequent error handling to handle it.
Tested with the reproducers from this report and the previous one,
with lksctp-tools and sctp-tests.
Reported-by: syzbot+9a1bc632e78a1a98488b@syzkaller.appspotmail.com
Fixes: 951c6db954 ("sctp: fix memleak on err handling of stream initialization")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the size of the receive buffer for a socket is close to 2^31 when
computing if we have enough space in the buffer to copy a packet from
the queue to the buffer we might hit an integer overflow.
When an user set net.core.rmem_default to a value close to 2^31 UDP
packets are dropped because of this overflow. This can be visible, for
instance, with failure to resolve hostnames.
This can be fixed by casting sk_rcvbuf (which is an int) to unsigned
int, similarly to how it is done in TCP.
Signed-off-by: Antonio Messina <amessina@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso,
including adding a missing ipv6 match description.
2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi
Bhat.
3) Fix uninit value in bond_neigh_init(), from Eric Dumazet.
4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold.
5) Fix use after free in tipc_disc_rcv(), from Tuong Lien.
6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul
Chaignon.
7) Multicast MAC limit test is off by one in qede, from Manish Chopra.
8) Fix established socket lookup race when socket goes from
TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening
RCU grace period. From Eric Dumazet.
9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet.
10) Fix active backup transition after link failure in bonding, from
Mahesh Bandewar.
11) Avoid zero sized hash table in gtp driver, from Taehee Yoo.
12) Fix wrong interface passed to ->mac_link_up(), from Russell King.
13) Fix DSA egress flooding settings in b53, from Florian Fainelli.
14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost.
15) Fix double free in dpaa2-ptp code, from Ioana Ciornei.
16) Reject invalid MTU values in stmmac, from Jose Abreu.
17) Fix refcount leak in error path of u32 classifier, from Davide
Caratti.
18) Fix regression causing iwlwifi firmware crashes on boot, from Anders
Kaseorg.
19) Fix inverted return value logic in llc2 code, from Chan Shu Tak.
20) Disable hardware GRO when XDP is attached to qede, frm Manish
Chopra.
21) Since we encode state in the low pointer bits, dst metrics must be
at least 4 byte aligned, which is not necessarily true on m68k. Add
annotations to fix this, from Geert Uytterhoeven.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits)
sfc: Include XDP packet headroom in buffer step size.
sfc: fix channel allocation with brute force
net: dst: Force 4-byte alignment of dst_metrics
selftests: pmtu: fix init mtu value in description
hv_netvsc: Fix unwanted rx_table reset
net: phy: ensure that phy IDs are correctly typed
mod_devicetable: fix PHY module format
qede: Disable hardware gro when xdp prog is installed
net: ena: fix issues in setting interrupt moderation params in ethtool
net: ena: fix default tx interrupt moderation interval
net/smc: unregister ib devices in reboot_event
net: stmmac: platform: Fix MDIO init for platforms without PHY
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
net: hisilicon: Fix a BUG trigered by wrong bytes_compl
net: dsa: ksz: use common define for tag len
s390/qeth: don't return -ENOTSUPP to userspace
s390/qeth: fix promiscuous mode after reset
s390/qeth: handle error due to unsupported transport mode
cxgb4: fix refcount init for TC-MQPRIO offload
tc-testing: initial tdc selftests for cls_u32
...
In the reboot_event handler, unregister the ib devices and enable
the IB layer to release the devices before the reboot.
Fixes: a33a803cfe ("net/smc: guarantee removal of link groups in reboot")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a frame with NULL DSAP is received, llc_station_rcv is called.
In turn, llc_stat_ev_rx_null_dsap_xid_c is called to check if it is a NULL
XID frame. The return statement of llc_stat_ev_rx_null_dsap_xid_c returns 1
when the incoming frame is not a NULL XID frame and 0 otherwise. Hence, a
NULL XID response is returned unexpectedly, e.g. when the incoming frame is
a NULL TEST command.
To fix the error, simply remove the conditional operator.
A similar error in llc_stat_ev_rx_null_dsap_test_c is also fixed.
Signed-off-by: Chan Shu Tak, Alex <alexchan@task.com.hk>
Signed-off-by: David S. Miller <davem@davemloft.net>
To enable iproute2/tipc to generate backwards compatible
printouts and validate command parameters for nodes using a
<z.c.n> node address, it needs to be able to read the legacy
address flag from the kernel. The legacy address flag records
the way in which the node identity was originally specified.
The legacy address flag is requested by the netlink message
TIPC_NL_ADDR_LEGACY_GET. If the flag is set the attribute
TIPC_NLA_NET_ADDR_LEGACY is set in the return message.
Signed-off-by: John Rutherford <john.rutherford@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove special taglen define KSZ8795_INGRESS_TAG_LEN
and use generic KSZ_INGRESS_TAG_LEN instead.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add comments on how the ring access functions are named and how they
are supposed to be used for producers and consumers. The functions are
also reordered so that the consumer functions are in the beginning and
the producer functions in the end, for easier reference. Put this in a
separate patch as the diff might look a little odd, but no
functionality has changed in this patch.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/1576759171-28550-12-git-send-email-magnus.karlsson@intel.com
There are two unnecessary READ_ONCE of descriptor data. These are not
needed since the data is written by the producer before it signals
that the data is available by incrementing the producer pointer. As the
access to this producer pointer is serialized and the consumer always
reads the descriptor after it has read and synchronized with the
producer counter, the write of the descriptor will have fully
completed and it does not matter if the consumer has any read tearing.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/1576759171-28550-11-git-send-email-magnus.karlsson@intel.com
Change the name of xsk_umem_discard_addr to xsk_umem_release_addr to
better reflect the new naming of the AF_XDP queue manipulation
functions. As this functions is used by drivers implementing support
for AF_XDP zero-copy, it requires a name change to these drivers. The
function xsk_umem_release_addr_rq has also changed name in the same
fashion.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/1576759171-28550-10-git-send-email-magnus.karlsson@intel.com
Change the names of the validation functions to better reflect what
they are doing. The uppermost ones are reading entries from the rings
and only the bottom ones validate entries. So xskq_cons_read_ is a
better prefix name.
Also change the xskq_cons_read_ functions to return a bool
as the the descriptor or address is already returned by reference
in the parameters. Everyone is using the return value as a bool
anyway.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/1576759171-28550-9-git-send-email-magnus.karlsson@intel.com
Simplify and refactor consumer ring functions. The consumer first
"peeks" to find descriptors or addresses that are available to
read from the ring, then reads them and finally "releases" these
descriptors once it is done. The two local variables cons_tail
and cons_head are turned into one single variable called
cached_cons. cached_tail referred to the cached value of the
global consumer pointer and will be stored in cached_cons. For
cached_head, we just use cached_prod instead as it was not used
for a consumer queue before. It also better reflects what it
really is now: a cached copy of the producer pointer.
The names of the functions are also renamed in the same manner as
the producer functions. The new functions are called xskq_cons_
followed by what it does.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/1576759171-28550-8-git-send-email-magnus.karlsson@intel.com
In the xsk consumer ring code there is a variable called RX_BATCH_SIZE
that dictates the minimum number of entries that we try to grab from
the fill and Tx rings. In fact, the code always try to grab the
maximum amount of entries from these rings. The only thing this
variable does is to throw an error if there is less than 16 (as it is
defined) entries on the ring. There is no reason to do this and it
will just lead to weird behavior from user space's point of view. So
eliminate this variable.
With this change, we will be able to simplify the xskq_nb_free and
xskq_nb_avail code in the next commit.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/1576759171-28550-6-git-send-email-magnus.karlsson@intel.com
Adopt the naming of the producer ring access functions to have a
similar naming convention as the functions in libbpf, but adapted to
the kernel. You first reserve a number of entries that you later
submit to the global state of the ring. This is much clearer, IMO,
than the one that was in the kernel part. Once renamed, we also
discover that two functions are actually the same, so remove one of
them. Some of the primitive ring submission operations are also the
same so break these out into __xskq_prod_submit that the upper level
ring access functions can use.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/1576759171-28550-5-git-send-email-magnus.karlsson@intel.com
Currently, the xsk ring code has two cached producer pointers:
prod_head and prod_tail. This patch consolidates these two into a
single one called cached_prod to make the code simpler and easier to
maintain. This will be in line with the user space part of the the
code found in libbpf, that only uses a single cached pointer.
The Rx path only uses the two top level functions
xskq_produce_batch_desc and xskq_produce_flush_desc and they both use
prod_head and never prod_tail. So just move them over to
cached_prod.
The Tx XDP_DRV path uses xskq_produce_addr_lazy and
xskq_produce_flush_addr_n and unnecessarily operates on both prod_tail
and prod_head, so move them over to just use cached_prod by skipping
the intermediate step of updating prod_tail.
The Tx path in XDP_SKB mode uses xskq_reserve_addr and
xskq_produce_addr. They currently use both cached pointers, but we can
operate on the global producer pointer in xskq_produce_addr since it
has to be updated anyway, thus eliminating the use of both cached
pointers. We can also remove the xskq_nb_free in xskq_produce_addr
since it is already called in xskq_reserve_addr. No need to do it
twice.
When there is only one cached producer pointer, we can also simplify
xskq_nb_free by removing one argument.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/1576759171-28550-4-git-send-email-magnus.karlsson@intel.com
In order to set the correct return flags for poll, the xsk code has to
check if the Rx queue is empty and if the Tx queue is full. This code
was unnecessarily large and complex as it used the functions that are
used to update the local state from the global state (xskq_nb_free and
xskq_nb_avail). Since we are not doing this nor updating any data
dependent on this state, we can simplify the functions. Another
benefit from this is that we can also simplify the xskq_nb_free and
xskq_nb_avail functions in a later commit.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/1576759171-28550-3-git-send-email-magnus.karlsson@intel.com
The lazy update threshold was introduced to keep the producer and
consumer some distance apart in the completion ring. This was
important in the beginning of the development of AF_XDP as the ring
format as that point in time was very sensitive to the producer and
consumer being on the same cache line. This is not the case
anymore as the current ring format does not degrade in any noticeable
way when this happens. Moreover, this threshold makes it impossible
to run the system with rings that have less than 128 entries.
So let us remove this threshold and just get one entry from the ring
as in all other functions. This will enable us to remove this function
in a later commit. Note that xskq_produce_addr_lazy followed by
xskq_produce_flush_addr_n are still not the same function as
xskq_produce_addr() as it operates on another cached pointer.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/1576759171-28550-2-git-send-email-magnus.karlsson@intel.com
