Pointer dev is initialized and then re-assigned with the same value
a little later, hence the second assignment is redundant and can be
removed.
Cleans up clang warning:
drivers/usb/wusbcore/wa-nep.c:88:17: warning: Value stored to 'dev'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel would like to have all stack VLA usage removed[1]. We
already have a pre-processor constant defined MAX_SGLEN. We can use
this instead of the variable param-sglen.
[1]: https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB device gets plugged on ASUS PRIME B350M-A's front ports, the
xHC stops working:
[ 549.114587] xhci_hcd 0000:02:00.0: WARN: xHC CMD_RUN timeout
[ 549.114608] suspend_common(): xhci_pci_suspend+0x0/0xc0 returns -110
[ 549.114638] xhci_hcd 0000:02:00.0: can't suspend (hcd_pci_runtime_suspend returned -110)
Delay before running xHC command CMD_RUN can workaround the issue.
Use a new quirk to make the delay only targets to the affected xHC.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reverts the commit 835e4241e7 ("usb: host: xhci-plat:
enable clk in resume timing") because this driver also has runtime PM
and the commit 560869100b ("clk: renesas: cpg-mssr: Restore module
clocks during resume") will restore the clock on R-Car H3 environment.
If the xhci_plat_suspend() disables the clk, the system cannot enable
the clk in resume like the following behavior:
< In resume >
- genpd_resume_noirq() runs and enable the clk (enable_count = 1)
- cpg_mssr_resume_noirq() restores the clk register.
-- Since the clk was disabled in suspend, cpg_mssr_resume_noirq()
will disable the clk and keep the enable_count.
- Even if xhci_plat_resume() calls clk_prepare_enable(), since
the enable_count is 1, the clk will be not enabled.
After this patch is applied, the cpg-mssr driver will save the clk
as enable, so the clk will be enabled in resume.
Fixes: 835e4241e7 ("usb: host: xhci-plat: enable clk in resume timing")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felipe writes:
usb: fixes for v4.16-rc4
Just small fixes now. The two most important are a fix for a a lock up
on USB ID pin change during system suspend/resume on dwc3 and a
use-after-free fix in ffs_fs_kill_sb().
Apart from that, some DT compatible fixes.
When the host wants to fetch OS descriptors, it sends two requests. The
first is only for the header and the second for the full amount
specified by the header in the first request. The OS descriptor handling
code is distinguishing the header-only requests based on the wLength of
the setup packet, but the same code is executed in both cases to
construct the actual header. Simplify this by always constructing the
header and then filling out the rest of the request if the wLength is
greater than the size of the header.
Also remove the duplicate code for queueing the request to ep0 by adding
a goto label.
Signed-off-by: Chris Dickens <christopher.a.dickens@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When handling an OS descriptor request, one of the first operations is
to zero out the request buffer using the wLength from the setup packet.
There is no bounds checking, so a wLength > 4096 would clobber memory
adjacent to the request buffer. Fix this by taking the min of wLength
and the request buffer length prior to the memset. While at it, define
the buffer length in a header file so that magic numbers don't appear
throughout the code.
When returning data to the host, the data length should be the min of
the wLength and the valid data we have to return. Currently we are
returning wLength, thus requests for a wLength greater than the amount
of data in the OS descriptor buffer would return invalid (albeit zero'd)
data following the valid descriptor data. Fix this by counting the
number of bytes when constructing the data and using this when
determining the length of the request.
Signed-off-by: Chris Dickens <christopher.a.dickens@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As devm_ioremap_resource() checks for valid resource,
make use of it instead of testing ourselves. As a bonus
memory region is requested.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Pointer tv_nexus is being initialized a value and this is never read
and is later being updated with the same value. Remove the redundant
initialization so that the assignment to tv_nexus is performed later
and more local to when it is being read.
Cleans up clang warning:
drivers/usb/gadget/function/f_tcm.c:1097:25: warning: Value stored to
'tv_nexus' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The local variable event is of type enum usb_phy_events. Use
the same enum value USB_EVENT_NONE instead of UX500_MUSB_NONE.
This avoids a warning when building with clang:
drivers/usb/phy/phy-ab8500-usb.c:906:30: warning: implicit conversion from
enumeration type 'enum ux500_musb_vbus_id_status' to different enumeration
type 'enum usb_phy_events' [-Wenum-conversion]
enum usb_phy_events event = UX500_MUSB_NONE;
~~~~~ ^~~~~~~~~~~~~~~
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
mxs_charger_secondary_detection() is only used in this file, so make
it static.
This fixes the following sparse warning:
drivers/usb/phy/phy-mxs-usb.c:581:23: warning: symbol 'mxs_charger_secondary_detection' was not declared. Should it be static?
Acked-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
commit d178bc3a70 ("user namespace: usb:
make usb urbs user namespace aware (v2)") changed kill_pid_info_as_uid
to kill_pid_info_as_cred, saving and passing a cred structure instead of
uids. Since the secid can be obtained from the cred, drop the secid fields
from the usb_dev_state and async structures, and drop the secid argument to
kill_pid_info_as_cred. Replace the secid argument to security_task_kill
with the cred. Update SELinux, Smack, and AppArmor to use the cred, which
avoids the need for Smack and AppArmor to use a secid at all in this hook.
Further changes to Smack might still be required to take full advantage of
this change, since it should now be possible to perform capability
checking based on the supplied cred. The changes to Smack and AppArmor
have only been compile-tested.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Paul Moore <paul@paul-moore.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Commit 57e6f0d7b8 ("typec: tcpm: Only request matching pdos") is causing
a regression, before this commit e.g. the GPD win and GPD pocket devices
were charging at 9V 3A with a PD charger, now they are instead slowly
discharging at 5V 0.4A, as this commit causes the ports max_snk_mv/ma/mw
settings to be completely ignored.
Arguably the way to fix this would be to add a PDO_VAR() describing the
voltage range to the snk_caps of boards which can handle any voltage in
their range, but the "typec: tcpm: Only request matching pdos" commit
looks at the type of PDO advertised by the source/charger and if that
is fixed (as it typically is) only compairs against PDO_FIXED entries
in the snk_caps so supporting a range of voltage would require adding a
PDO_FIXED entry for *every possible* voltage to snk_caps.
AFAICT there is no reason why a fixed source_cap cannot be matched against
a variable snk_cap, so at a minimum the commit should be rewritten to
support that.
For now lets revert the "typec: tcpm: Only request matching pdos" commit,
fixing the regression.
Fixes: 57e6f0d7b8 ("typec: tcpm: Only request matching pdos")
Cc: Badhri Jagan Sridharan <badhri@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without pm_runtime_{get,put}_sync calls in place, reading
vbus status via /sys causes the following error:
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0ab060
pgd = b333e822
[fa0ab060] *pgd=48011452(bad)
[<c05261b0>] (musb_default_readb) from [<c0525bd0>] (musb_vbus_show+0x58/0xe4)
[<c0525bd0>] (musb_vbus_show) from [<c04c0148>] (dev_attr_show+0x20/0x44)
[<c04c0148>] (dev_attr_show) from [<c0259f74>] (sysfs_kf_seq_show+0x80/0xdc)
[<c0259f74>] (sysfs_kf_seq_show) from [<c0210bac>] (seq_read+0x250/0x448)
[<c0210bac>] (seq_read) from [<c01edb40>] (__vfs_read+0x1c/0x118)
[<c01edb40>] (__vfs_read) from [<c01edccc>] (vfs_read+0x90/0x144)
[<c01edccc>] (vfs_read) from [<c01ee1d0>] (SyS_read+0x3c/0x74)
[<c01ee1d0>] (SyS_read) from [<c0106fe0>] (ret_fast_syscall+0x0/0x54)
Solution was suggested by Tony Lindgren <tony@atomide.com>.
Signed-off-by: Merlijn Wajer <merlijn@wizzup.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Corsair Strafe RGB keyboard does not respond to usb control messages
sometimes and hence generates timeouts.
Commit de3af5bf25 ("usb: quirks: add delay init quirk for Corsair
Strafe RGB keyboard") tried to fix those timeouts by adding
USB_QUIRK_DELAY_INIT.
Unfortunately, even with this quirk timeouts of usb_control_msg()
can still be seen, but with a lower frequency (approx. 1 out of 15):
[ 29.103520] usb 1-8: string descriptor 0 read error: -110
[ 34.363097] usb 1-8: can't set config #1, error -110
Adding further delays to different locations where usb control
messages are issued just moves the timeouts to other locations,
e.g.:
[ 35.400533] usbhid 1-8:1.0: can't add hid device: -110
[ 35.401014] usbhid: probe of 1-8:1.0 failed with error -110
The only way to reliably avoid those issues is having a pause after
each usb control message. In approx. 200 boot cycles no more timeouts
were seen.
Addionaly, keep USB_QUIRK_DELAY_INIT as it turned out to be necessary
to have the delay in hub_port_connect() after hub_port_init().
The overall boot time seems not to be influenced by these additional
delays, even on fast machines and lightweight distributions.
Fixes: de3af5bf25 ("usb: quirks: add delay init quirk for Corsair Strafe RGB keyboard")
Cc: stable@vger.kernel.org
Signed-off-by: Danilo Krummrich <danilokrummrich@dk-develop.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When I debug a kernel crash issue in funcitonfs, found ffs_data.ref
overflowed, While functionfs is unmounting, ffs_data is put twice.
Commit 43938613c6 ("drivers, usb: convert ffs_data.ref from atomic_t to
refcount_t") can avoid refcount overflow, but that is risk some situations.
So no need put ffs data in ffs_fs_kill_sb, already put in ffs_data_closed.
The issue can be reproduced in Mediatek mt6763 SoC, ffs for ADB device.
KASAN enabled configuration reports use-after-free errro.
BUG: KASAN: use-after-free in refcount_dec_and_test+0x14/0xe0 at addr ffffffc0579386a0
Read of size 4 by task umount/4650
====================================================
BUG kmalloc-512 (Tainted: P W O ): kasan: bad access detected
-----------------------------------------------------------------------------
INFO: Allocated in ffs_fs_mount+0x194/0x844 age=22856 cpu=2 pid=566
alloc_debug_processing+0x1ac/0x1e8
___slab_alloc.constprop.63+0x640/0x648
__slab_alloc.isra.57.constprop.62+0x24/0x34
kmem_cache_alloc_trace+0x1a8/0x2bc
ffs_fs_mount+0x194/0x844
mount_fs+0x6c/0x1d0
vfs_kern_mount+0x50/0x1b4
do_mount+0x258/0x1034
INFO: Freed in ffs_data_put+0x25c/0x320 age=0 cpu=3 pid=4650
free_debug_processing+0x22c/0x434
__slab_free+0x2d8/0x3a0
kfree+0x254/0x264
ffs_data_put+0x25c/0x320
ffs_data_closed+0x124/0x15c
ffs_fs_kill_sb+0xb8/0x110
deactivate_locked_super+0x6c/0x98
deactivate_super+0xb0/0xbc
INFO: Object 0xffffffc057938600 @offset=1536 fp=0x (null)
......
Call trace:
[<ffffff900808cf5c>] dump_backtrace+0x0/0x250
[<ffffff900808d3a0>] show_stack+0x14/0x1c
[<ffffff90084a8c04>] dump_stack+0xa0/0xc8
[<ffffff900826c2b4>] print_trailer+0x158/0x260
[<ffffff900826d9d8>] object_err+0x3c/0x40
[<ffffff90082745f0>] kasan_report_error+0x2a8/0x754
[<ffffff9008274f84>] kasan_report+0x5c/0x60
[<ffffff9008273208>] __asan_load4+0x70/0x88
[<ffffff90084cd81c>] refcount_dec_and_test+0x14/0xe0
[<ffffff9008d98f9c>] ffs_data_put+0x80/0x320
[<ffffff9008d9d904>] ffs_fs_kill_sb+0xc8/0x110
[<ffffff90082852a0>] deactivate_locked_super+0x6c/0x98
[<ffffff900828537c>] deactivate_super+0xb0/0xbc
[<ffffff90082af0c0>] cleanup_mnt+0x64/0xec
[<ffffff90082af1b0>] __cleanup_mnt+0x10/0x18
[<ffffff90080d9e68>] task_work_run+0xcc/0x124
[<ffffff900808c8c0>] do_notify_resume+0x60/0x70
[<ffffff90080866e4>] work_pending+0x10/0x14
Cc: stable@vger.kernel.org
Signed-off-by: Xinyong <xinyong.fang@linux.alibaba.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To reproduce the lock up do the following
- connect otg host adapter and a USB device to the dual-role port
so that it is in host mode.
- suspend to mem.
- disconnect otg adapter.
- resume the system.
If we call dwc3_host_exit() before tasks are thawed
xhci_plat_remove() seems to lock up at the second usb_remove_hcd() call.
To work around this we queue the _dwc3_set_mode() work on
the system_freezable_wq.
Fixes: 41ce1456e1 ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: <stable@vger.kernel.org> # v4.12+
Suggested-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This expands the no-op dummy functions into full prototypes to avoid
indirect call mismatches when running under Control Flow Integrity
checking, like with Clang's -fsanitize=cfi.
Co-Developed-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As done in commit:
724ba8b30b ("console/dummy: leave .con_font_get set to NULL")
This drops the dummy .con_font_get(), as it could leave arguments
uninitialized.
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull USB fixes from Greg KH:
"Here are a number of USB fixes for 4.16-rc3
Nothing major, but a number of different fixes all over the place in
the USB stack for reported issues. Mostly gadget driver fixes,
although the typical set of xhci bugfixes are there, along with some
new quirks additions as well.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (39 commits)
Revert "usb: musb: host: don't start next rx urb if current one failed"
usb: musb: fix enumeration after resume
usb: cdc_acm: prevent race at write to acm while system resumes
Add delay-init quirk for Corsair K70 RGB keyboards
usb: ohci: Proper handling of ed_rm_list to handle race condition between usb_kill_urb() and finish_unlinks()
usb: host: ehci: always enable interrupt for qtd completion at test mode
usb: ldusb: add PIDs for new CASSY devices supported by this driver
usb: renesas_usbhs: missed the "running" flag in usb_dmac with rx path
usb: host: ehci: use correct device pointer for dma ops
usbip: keep usbip_device sockfd state in sync with tcp_socket
ohci-hcd: Fix race condition caused by ohci_urb_enqueue() and io_watchdog_func()
USB: serial: option: Add support for Quectel EP06
xhci: fix xhci debugfs errors in xhci_stop
xhci: xhci debugfs device nodes weren't removed after device plugged out
xhci: Fix xhci debugfs devices node disappearance after hibernation
xhci: Fix NULL pointer in xhci debugfs
xhci: Don't print a warning when setting link state for disabled ports
xhci: workaround for AMD Promontory disabled ports wakeup
usb: dwc3: core: Fix ULPI PHYs and prevent phy_get/ulpi_init during suspend/resume
USB: gadget: udc: Add missing platform_device_put() on error in bdc_pci_probe()
...
Instead of kmalloc() with manually calculated values followed by
multiple strcpy()/strcat() calls, just fold it all into a single
kasprintf() call.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On dm3730 there are enumeration problems after resume.
Investigation led to the cause that the MUSB_POWER_SOFTCONN
bit is not set. If it was set before suspend (because it
was enabled via musb_pullup()), it is set in
musb_restore_context() so the pullup is enabled. But then
musb_start() is called which overwrites MUSB_POWER and
therefore disables MUSB_POWER_SOFTCONN, so no pullup is
enabled and the device is not enumerated.
So let's do a subset of what musb_start() does
in the same way as musb_suspend() does it. Platform-specific
stuff it still called as there might be some phy-related stuff
which needs to be enabled.
Also interrupts are enabled, as it was the original idea
of calling musb_start() in musb_resume() according to
Commit 6fc6f4b87c ("usb: musb: Disable interrupts on suspend,
enable them on resume")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
