Clean up the throttle implementation by dropping the redundant
throttle_req flag which was a remnant from back when USB serial had only
a single read URB, something which was later carried over to cdc-acm.
Also convert the throttled flag to an atomic bit flag.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix two long-standing bugs which could potentially lead to memory
corruption or leave the port throttled until it is reopened (on weakly
ordered systems), respectively, when read-URB completion races with
unthrottle().
First, the URB must not be marked as free before processing is complete
to prevent it from being submitted by unthrottle() on another CPU.
CPU 1 CPU 2
================ ================
complete() unthrottle()
process_urb();
smp_mb__before_atomic();
set_bit(i, free); if (test_and_clear_bit(i, free))
submit_urb();
Second, the URB must be marked as free before checking the throttled
flag to prevent unthrottle() on another CPU from failing to observe that
the URB needs to be submitted if complete() sees that the throttled flag
is set.
CPU 1 CPU 2
================ ================
complete() unthrottle()
set_bit(i, free); throttled = 0;
smp_mb__after_atomic(); smp_mb();
if (throttled) if (test_and_clear_bit(i, free))
return; submit_urb();
Note that test_and_clear_bit() only implies barriers when the test is
successful. To handle the case where the URB is still in use an explicit
barrier needs to be added to unthrottle() for the second race condition.
Also note that the first race was fixed by 36e59e0d70 ("cdc-acm: fix
race between callback and unthrottle") back in 2015, but the bug was
reintroduced a year later.
Fixes: 1aba579f3c ("cdc-acm: handle read pipe errors")
Fixes: 088c64f812 ("USB: cdc-acm: re-write read processing")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This update for DaVinci SoC support simplifies the VBUS enable
and overcurrent handling code in DA8XX OHCI driver by modeling
vbus GPIO as a regulator. This unifies code for all users, device
tree and non-device-tree.
The OHCI driver patches have been acked by its maintainer.
* tag 'davinci-for-v5.2/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
usb: ohci-da8xx: drop the vbus GPIO
ARM: davinci: da830-evm: add a fixed regulator for ohci-da8xx
ARM: davinci: omapl138-hawk: add a fixed regulator for ohci-da8xx
usb: ohci-da8xx: disable the regulator if the overcurrent irq fired
usb: ohci-da8xx: let the regulator framework keep track of use count
ARM: davinci: add missing sentinels to GPIO lookup tables
Signed-off-by: Olof Johansson <olof@lixom.net>
The configure endpoint command configures all the endpoints that were
flagged to be added or dropped.
To know the content of each of the added endpoints we need to add tracing
to the .add_endpoint() callback, just after initializing all the context
values.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add tracing for the add and drop bits in the input control context
used in Address device, configure endpoint, evaluate context commands.
The add and drop bits tell xHC which enpoints are added and dropped.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve port related dynamic debugging by printing out the bus number,
port number and port status register content each time there is a port
related debug messages.
Use the same port numbering method as usbcore to simplify debugging.
i.e. starting with port number 1.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Immediate data transfers (IDT) allow the HCD to copy small chunks of
data (up to 8bytes) directly into its output transfer TRBs. This avoids
the somewhat expensive DMA mappings that are performed by default on
most URBs submissions.
In the case an URB was suitable for IDT. The data is directly copied
into the "Data Buffer Pointer" region of the TRB and the IDT flag is
set. Instead of triggering memory accesses the HC will use the data
directly.
The implementation could cover all kind of output endpoints. Yet
Isochronous endpoints are bypassed as I was unable to find one that
matched IDT's constraints. As we try to bypass the default DMA mappings
on URB buffers we'd need to find a Isochronous device with an
urb->transfer_buffer_length <= 8 bytes.
The implementation takes into account that the 8 byte buffers provided
by the URB will never cross a 64KB boundary.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's pointless to scan the hub' i2c-bus segment if GPIOs aren't supported
by the system, since no GPIO-driven reset could be cleared by the driver
then. Moreover if CONFIG_GPIOLIB is disabled the gpio_chip structure
definition won't be available, which causes the incomplete type pointer
dereference compilation error. In order to fix this we need to create an
empty usb251x_check_gpio_chip() method returning zero, so the driver would
skip the i2c-bus segment checking and proceed with further probing in this
case.
Fixes: 6e3c8beb4f ("usb: usb251xb: Lock i2c-bus segment the hub resides")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Override the initial terminal settings provided by core directly instead
of first resetting them to tty_std_termios.
Also reorder the cflags as they are usually seen (in bit order).
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop bogus TIOCM_CTS, which is not a cflag, from the initial terminal
settings.
Note that the corresponding bit is already set by CS8.
Signed-off-by: Johan Hovold <johan@kernel.org>
Now that init_termios() is only called on first use, we can clean up the
cypress_m8 initial-termios handling.
Note that only the earthmate chip type used settings different from the
defaults provided by USB serial core, and that the chip type is indeed
known when init_termios is called at tty-install time.
Signed-off-by: Johan Hovold <johan@kernel.org>
The initial terminal settings set by the driver matches the default
settings provided by core so drop the redundant init_termios callback.
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB-serial driver init_termios callback is used to override the
default initial terminal settings provided by USB-serial core.
After a bug was fixed in the original implementation introduced by
commit fe1ae7fdd2 ("tty: USB serial termios bits"), the init_termios
callback was no longer called just once on first use as intended but
rather on every (first) open.
This specifically meant that the terminal settings saved on (final)
close were ignored when reopening a port for drivers overriding the
initial settings.
Also update the outdated function header referring to the creation of
termios objects.
Fixes: 7e29bb4b77 ("usb-serial: fix termios initialization logic")
Signed-off-by: Johan Hovold <johan@kernel.org>
The syzkaller USB fuzzer found a general-protection-fault bug in the
yurex driver. The fault occurs when a device has been unplugged; the
driver's interrupt-URB handler logs an error message referring to the
device by name, after the device has been unregistered and its name
deallocated.
This problem is caused by the fact that the interrupt URB isn't
cancelled until the driver's private data structure is released, which
can happen long after the device is gone. The cure is to make sure
that the interrupt URB is killed before yurex_disconnect() returns;
this is exactly the sort of thing that usb_poison_urb() was meant for.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+2eb9121678bdb36e6d57@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change the validation of number_of_packets in get_pipe to compare the
number of packets to a fixed maximum number of packets allowed, set to
be 1024. This number was chosen due to it being used by other drivers as
well, for example drivers/usb/host/uhci-q.c
Background/reason:
The get_pipe function in stub_rx.c validates the number of packets in
isochronous mode and aborts with an error if that number is too large,
in order to prevent malicious input from possibly triggering large
memory allocations. This was previously done by checking whether
pdu->u.cmd_submit.number_of_packets is bigger than the number of packets
that would be needed for pdu->u.cmd_submit.transfer_buffer_length bytes
if all except possibly the last packet had maximum length, given by
usb_endpoint_maxp(epd) * usb_endpoint_maxp_mult(epd). This leads to an
error if URBs with packets shorter than the maximum possible length are
submitted, which is allowed according to
Documentation/driver-api/usb/URB.rst and occurs for example with the
snd-usb-audio driver.
Fixes: c6688ef9f2 ("usbip: fix stub_rx: harden CMD_SUBMIT path to handle malicious input")
Signed-off-by: Malte Leip <malte@leip.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change will send an OFFLINE event to udev with the ERROR=DEAD
environment variable set when the HC dies.
By notifying user space the appropriate policies can be applied.
i.e.,
* Collect error logs.
* Notify the user that USB is no longer functional.
* Perform a graceful reboot.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Latest NVIDIA GPUs support VirtualLink device. Since USBIF
has not assigned a Standard ID (SID) for VirtualLink
so using NVIDA VID 0x955 as SVID.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VirtualLink standard extends the DisplayPort Alt Mode by
utilizing also the USB 2 pins on the USB Type-C connector.
It uses the same messages as DisplayPort, but not the DP
SVID. At the time of writing, USB IF has not assigned a
Standard ID (SID) for VirtualLink, so the manufacturers of
VirtualLink adapters use their Vendor IDs as the SVID.
Since the SVID specific communication is exactly the same as
with DisplayPort alternate mode, there is no need to
implement separate driver for VirtualLink. We'll handle the
current VirtualLink adapters with probe drivers, and once
there is SVID assigned for it, we add it to the displayport
alt mode driver.
To support probing drivers, exporting the probe and remove
functions, and also changing the DP_HEADER helper macro to
use the SVID of the alternate mode device instead of the
DisplayPort alt mode SVID.
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes it possible to bind a driver to a DisplayPort
alt mode adapter devices.
The driver attempts to cope with the limitations of UCSI by
"emulating" behaviour and attempting to guess things when
ever possible in order to satisfy the requirements the
standard DisplayPort alt mode driver has.
Tested-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With UCSI the alternate modes, just like everything else
related to USB Type-C connectors, are handled in firmware.
The operating system can see the status and is allowed to
request certain things, for example entering and exiting the
modes, but the support for alternate modes is very limited
in UCSI. The feature is also optional, which means that even
when the platform supports alternate modes, the operating
system may not be even made aware of them.
UCSI does not support direct VDM reading or writing.
Instead, alternate modes can be entered and exited using a
single custom command which takes also an optional SVID
specific configuration value as parameter. That means every
supported alternate mode has to be handled separately in
UCSI driver.
This commit does not include support for any specific
alternate mode. The discovered alternate modes are now
registered, but binding a driver to an alternate mode will
not be possible until support for that alternate mode is
added to the UCSI driver.
Tested-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CCGx has two copies of the firmware in addition to the bootloader.
If the device is running FW1, FW2 can be updated with the new version.
Dual firmware mode allows the CCG device to stay in a PD contract and
support USB PD and Type-C functionality while a firmware update is in
progress.
First we read the currently flashed firmware version of both
primary and secondary firmware and then compare it with
version of firmware file to determine if flashing is required.
Command framework is added to support sending commands to CCGx
controller. We wait for response after sending the command and then
read the response from RAB_RESPONSE register.
Below commands are supported,
- ENTER_FLASHING
- RESET
- PDPORT_ENABLE
- JUMP_TO_BOOT
- FLASH_ROW_RW
- VALIDATE_FW
Command specific mutex lock is also added to sync between driver
and user threads.
PD port number information is added which is required while sending
PD_PORT_ENABLE command
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
[ heikki: Added ABI documentation. ]
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function is to get the details of ccg firmware and device version.
It will be useful in debugging and also during firmware update.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SMBus slave configuration is activated by CFG_SEL[1:0]=0x1 pins
state. This is the mode the hub is supposed to be to let this driver
work correctly. But a race condition might happen right after reset
is cleared due to CFG_SEL[0] pin being multiplexed with SMBus SCL
function. In case if the reset pin is handled by a i2c GPIO expander,
which is also placed at the same i2c-bus segment as the usb251x
SMB-interface connected to, then the hub reset clearance might
cause the CFG_SEL[0] being latched in unpredictable state. So
sometimes the hub configuration mode might be 0x1 (as expected),
but sometimes being 0x0, which doesn't imply to have the hub SMBus-slave
interface activated and consequently causes this driver failure.
In order to fix the problem we must make sure the GPIO-reset chip doesn't
reside the same i2c-bus segment as the SMBus-interface of the hub. If
it doesn't, we can safely block the segment for the time the reset is
cleared to prevent anyone generating a traffic at the i2c-bus SCL lane
connected to the CFG_SEL[0] pin. But if it does, nothing we can do, so
just return an error. If we locked the i2c-bus segment and tried to
communicate with the GPIO-expander, it would cause a deadlock. If we didn't
lock the i2c-bus segment, it would randomly cause the CFG_SEL[0] bit flip.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keep EXTCON support optional, as some platforms do not need it.
Do the same for USB_DWC3_OMAP while we're at it.
Fixes: 3def4031b3 ("usb: dwc3: add EXTCON dependency for qcom")
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up set_termios() by adding missing white space around operators
and making a couple of continuation lines more readable.
Also drop a couple of redundant braces.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up modem-control handling somewhat by adding missing whitespace
around operators and splitting a long statement in two.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The syzkaller fuzzer reported a bug in the USB hub driver which turned
out to be caused by a negative runtime-PM usage counter. This allowed
a hub to be runtime suspended at a time when the driver did not expect
it. The symptom is a WARNING issued because the hub's status URB is
submitted while it is already active:
URB 0000000031fb463e submitted while active
WARNING: CPU: 0 PID: 2917 at drivers/usb/core/urb.c:363
The negative runtime-PM usage count was caused by an unfortunate
design decision made when runtime PM was first implemented for USB.
At that time, USB class drivers were allowed to unbind from their
interfaces without balancing the usage counter (i.e., leaving it with
a positive count). The core code would take care of setting the
counter back to 0 before allowing another driver to bind to the
interface.
Later on when runtime PM was implemented for the entire kernel, the
opposite decision was made: Drivers were required to balance their
runtime-PM get and put calls. In order to maintain backward
compatibility, however, the USB subsystem adapted to the new
implementation by keeping an independent usage counter for each
interface and using it to automatically adjust the normal usage
counter back to 0 whenever a driver was unbound.
This approach involves duplicating information, but what is worse, it
doesn't work properly in cases where a USB class driver delays
decrementing the usage counter until after the driver's disconnect()
routine has returned and the counter has been adjusted back to 0.
Doing so would cause the usage counter to become negative. There's
even a warning about this in the USB power management documentation!
As it happens, this is exactly what the hub driver does. The
kick_hub_wq() routine increments the runtime-PM usage counter, and the
corresponding decrement is carried out by hub_event() in the context
of the hub_wq work-queue thread. This work routine may sometimes run
after the driver has been unbound from its interface, and when it does
it causes the usage counter to go negative.
It is not possible for hub_disconnect() to wait for a pending
hub_event() call to finish, because hub_disconnect() is called with
the device lock held and hub_event() acquires that lock. The only
feasible fix is to reverse the original design decision: remove the
duplicate interface-specific usage counter and require USB drivers to
balance their runtime PM gets and puts. As far as I know, all
existing drivers currently do this.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+7634edaea4d0b341c625@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_clk_get_optional() to get optional clock instead of
optional_clk_get() which uses devm_clk_get() to get clock and
checks for -EPROBE_DEFER but not -ENOENT as devm_clk_get_optional()
does, in fact, only ignoring -ENOENT will cover more errors, so
the replacement doesn't change original purpose.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the driver tries to get optional clock, it ignores all errors except
-EPROBE_DEFER, but if only ignores -ENOENT, it will cover some real errors,
such as -ENOMEM, so use devm_clk_get_optional() to get optional clock.
Cc: Peter Chen <Peter.Chen@nxp.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Peter Chen <Peter.Chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the driver tries to get optional clock, it ignores all errors,
but if only ignores -ENOENT, it will cover some real errors, such as
-EPROBE_DEFER, so use devm_clk_get_optional() to get optional clock.
Cc: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the driver tries to get optional clock, it ignores all errors except
-EPROBE_DEFER, but if only ignores -ENOENT, it will cover some real errors,
such as -ENOMEM, so use devm_clk_get_optional() to get optional clock.
And remove unnecessary stack variable clk.
Cc: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the driver tries to get optional clock, it ignores all errors except
-EPROBE_DEFER, but if only ignores -ENOENT, it will cover some real errors,
such as -ENOMEM, so use devm_clk_get_optional() to get optional clock.
Cc: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_clk_get_optional() to get optional clock instead of
optional_clk_get() which uses devm_clk_get() to get clock and
checks for -EPROBE_DEFER but not -ENOENT as devm_clk_get_optional()
does, in fact, only ignoring -ENOENT will cover more errors, so the
replacement doesn't change original purpose.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some tcpc device-drivers need to explicitly be told to watch for connection
events, otherwise the tcpc will not generate any TCPM_CC_EVENTs and devices
being plugged into the Type-C port will not be noticed.
For dual-role ports tcpm_start_drp_toggling() is used to tell the tcpc to
watch for connection events. But for single-role ports we've so far been
falling back to just calling tcpm_set_cc(). For some tcpc-s such as the
fusb302 this is not enough and no TCPM_CC_EVENT will be generated.
Commit ea3b4d5523 ("usb: typec: fusb302: Resolve fixed power role
contract setup") fixed SRPs not working because of this by making the
fusb302 driver start connection detection on every tcpm_set_cc() call.
It turns out this breaks src->snk power-role swapping because during the
swap we first set the Cc pins to Rp, calling set_cc, and then send a PS_RDY
message. But the fusb302 cannot send PD messages while its toggling engine
is active, so sending the PS_RDY message fails.
Struct tcpc_dev now has a new start_srp_connection_detect callback and
fusb302.c now implements this. This callback gets called when we the
fusb302 needs to start connection detection, fixing fusb302 SRPs not
seeing connected devices.
This allows us to revert the changes to fusb302's set_cc implementation,
making it once again purely setup the Cc-s and matching disconnect
detection, fixing src->snk power-role swapping no longer working.
Note that since the code was refactored in between, codewise this is not a
straight forward revert. Functionality wise this is a straight revert and
the original functionality is fully restored.
Fixes: ea3b4d5523 ("usb: typec: fusb302: Resolve fixed power role ...")
Cc: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When in single-role port mode, we must start single-role toggling to
get an interrupt when a device / cable gets plugged into the port.
This commit modifies the fusb302 start_toggling implementation to
start toggling for all port-types, so that connection-detection works
on single-role ports too.
Fixes: ea3b4d5523bc("usb: typec: fusb302: Resolve fixed power role ...")
Cc: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some tcpc device-drivers need to explicitly be told to watch for connection
events, otherwise the tcpc will not generate any TCPM_CC_EVENTs and devices
being plugged into the Type-C port will not be noticed.
For dual-role ports tcpm_start_drp_toggling() is used to tell the tcpc to
watch for connection events. Sofar we lack a similar callback to the tcpc
for single-role ports. With some tcpc-s such as the fusb302 this means
no TCPM_CC_EVENTs will be generated when the port is configured as a
single-role port.
This commit renames start_drp_toggling to start_toggling and since the
device-properties are parsed by the tcpm-core, adds a port_type parameter
to the start_toggling callback so that the tcpc_dev driver knows the
port-type and can act accordingly when it starts toggling.
The new start_toggling callback now always gets called if defined, instead
of only being called for DRP ports.
To avoid this causing undesirable functional changes all existing
start_drp_toggling implementations are not only renamed to start_toggling,
but also get a port_type check added and return -EOPNOTSUPP when port_type
is not DRP.
Fixes: ea3b4d5523bc("usb: typec: fusb302: Resolve fixed power role ...")
Cc: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fhci_queue_urb() shouldn't use urb->pipe to compute the maxpacket
size anyway.It should use usb_endpoint_maxp(&urb->ep->desc).
Signed-off-by: Yan Zhu <zhuyan34@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzkaller USB fuzzer identified a failure mode in which dummy-hcd
would never give back an unlinked URB. This causes usb_kill_urb() to
hang, leading to WARNINGs and unkillable threads.
In dummy-hcd, all URBs are given back by the dummy_timer() routine as
it scans through the list of pending URBS. Failure to give back URBs
can be caused by failure to start or early exit from the scanning
loop. The code currently has two such pathways: One is triggered when
an unsupported bus transfer speed is encountered, and the other by
exhausting the simulated bandwidth for USB transfers during a frame.
This patch removes those two paths, thereby allowing all unlinked URBs
to be given back in a timely manner. It adds a check for the bus
speed when the gadget first starts running, so that dummy_timer() will
never thereafter encounter an unsupported speed. And it prevents the
loop from exiting as soon as the total bandwidth has been used up (the
scanning loop continues, giving back unlinked URBs as they are found,
but not transferring any more data).
Thanks to Andrey Konovalov for manually running the syzkaller fuzzer
to help track down the source of the bug.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+d919b0f29d7b5a4994b9@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SCSI core does not like to have devices or hosts unregistered
while error recovery is in progress. Trying to do so can lead to
self-deadlock: Part of the removal code tries to obtain a lock already
held by the error handler.
This can cause problems for the usb-storage and uas drivers, because
their error handler routines perform a USB reset, and if the reset
fails then the USB core automatically goes on to unbind all drivers
from the device's interfaces -- all while still in the context of the
SCSI error handler.
As it turns out, practically all the scenarios leading to a USB reset
failure end up causing a device disconnect (the main error pathway in
usb_reset_and_verify_device(), at the end of the routine, calls
hub_port_logical_disconnect() before returning). As a result, the
hub_wq thread will soon become aware of the problem and will unbind
all the device's drivers in its own context, not in the
error-handler's context.
This means that usb_reset_device() does not need to call
usb_unbind_and_rebind_marked_interfaces() in cases where
usb_reset_and_verify_device() has returned an error, because hub_wq
will take care of everything anyway.
This particular problem was observed in somewhat artificial
circumstances, by using usbfs to tell a hub to power-down a port
connected to a USB-3 mass storage device using the UAS protocol. With
the port turned off, the currently executing command timed out and the
error handler started running. The USB reset naturally failed,
because the hub port was off, and the error handler deadlocked as
described above. Not carrying out the call to
usb_unbind_and_rebind_marked_interfaces() fixes this issue.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Kento Kobayashi <Kento.A.Kobayashi@sony.com>
Tested-by: Kento Kobayashi <Kento.A.Kobayashi@sony.com>
CC: Bart Van Assche <bvanassche@acm.org>
CC: Martin K. Petersen <martin.petersen@oracle.com>
CC: Jacky Cao <Jacky.Cao@sony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB subsystem has always had an unusual requirement for its
scatter-gather transfers: Each element in the scatterlist (except the
last one) must have a length divisible by the bulk maxpacket size.
This is a particular issue for USB mass storage, which uses SG lists
created by the block layer rather than setting up its own.
So far we have scraped by okay because most devices have a logical
block size of 512 bytes or larger, and the bulk maxpacket sizes for
USB 2 and below are all <= 512. However, USB 3 has a bulk maxpacket
size of 1024. Since the xhci-hcd driver includes native SG support,
this hasn't mattered much. But now people are trying to use USB-3
mass storage devices with USBIP, and the vhci-hcd driver currently
does not have full SG support.
The result is an overflow error, when the driver attempts to implement
an SG transfer of 63 512-byte blocks as a single
3584-byte (7 blocks) transfer followed by seven 4096-byte (8 blocks)
transfers. The device instead sends 31 1024-byte packets followed by
a 512-byte packet, and this overruns the first SG buffer.
Ideally this would be fixed by adding better SG support to vhci-hcd.
But for now it appears we can work around the problem by
asking the block layer to respect the maxpacket limitation, through
the use of the virt_boundary_mask.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Seth Bollinger <Seth.Bollinger@digi.com>
Tested-by: Seth Bollinger <Seth.Bollinger@digi.com>
CC: Ming Lei <tom.leiming@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some drivers (such as the vub300 MMC driver) expect usb_string() to
return a properly NUL-terminated string, even when an error occurs.
(In fact, vub300's probe routine doesn't bother to check the return
code from usb_string().) When the driver goes on to use an
unterminated string, it leads to kernel errors such as
stack-out-of-bounds, as found by the syzkaller USB fuzzer.
An out-of-range string index argument is not at all unlikely, given
that some devices don't provide string descriptors and therefore list
0 as the value for their string indexes. This patch makes
usb_string() return a properly terminated empty string along with the
-EINVAL error code when an out-of-range index is encountered.
And since a USB string index is a single-byte value, indexes >= 256
are just as invalid as values of 0 or below.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+b75b85111c10b8d680f1@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The returned value in status has never been used since
commit 4296c70a5e ("USB/xHCI: Enable USB 3.0 hub remote wakeup.")
So remove 'status' completely.
Remove warning (W=1):
drivers/usb/core/hub.c:3671:8: warning: variable 'status' set but not used [-Wunused-but-set-variable]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds Tegra186 XUSB host mode controller support. This is
very similar to the existing support for Tegra124 and Tegra210, except
that the number of ports and PHYs differs and the IPFS wrapper being
gone.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
