The channels spfi->tx_ch and spfi->rx_ch are not set to NULL after they
are released. As a result, they will be released again, either on the
error handling branch in the same function or in the corresponding
remove function, i.e. img_spfi_remove(). This patch fixes the bug by
setting the two members to NULL.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/1573007769-20131-1-git-send-email-bianpan2016@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the TXX9 SPI driver to use GPIO descriptors
to control the GPIO chip selects.
As the driver was clearly (ab)using the device tree "reg"
property to offset into the global GPIO chip we have to
add a hack to counter the hack: add a 1-to-1 chip select
to GPIO offset mapping for all 16 lines on the TXX9 GPIO
chip. The details are described in a largeish comment
in the patch.
We do not need to set up the GPIO as output any more since
the core will take care of this, as well as it will handle
the polarity inversion semantics.
Cc: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191030073832.24038-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When rebooting system, the PMIC watchdog time loading may not be loaded
correctly when another system is feeding the PMIC watchdog, since we did
not check the watchdog busy status before loading time values.
Thus we should set the BIT_WDG_NEW bit before loading time values, that
can support multiple loads without checking busy status to make sure the
time values can be loaded successfully to avoid this potential issue.
Signed-off-by: Lingling Xu <ling_ling.xu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/5655318a7252c9ea518c2f7950a61228ab8f42bf.1572257085.git.baolin.wang@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver does the wrong thing when cs_change is set on a non-last
xfer in a message. When cs_change is set, the driver deactivates the
CS and leaves it off until a later xfer again has cs_change set whereas
it should be briefly toggling CS off and on again.
This patch brings the behaviour of the driver back in line with the
documentation and common sense. The delay of 10 us is the same as is
used by the default spi_transfer_one_message() function in spi.c.
[gregory: rebased on for-5.5 from spi tree]
Fixes: 8090d6d1a4 ("spi: atmel: Refactor spi-atmel to use SPI framework queue")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191018153504.4249-1-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the previous implementation of this driver, the index of the GPIO
used as CS was linked to the offset of the CS register used to
configure the transfer.
With this new implementation the first CS register not used by
internal CS is associated to all the GPIO CS. It allows to not be
anymore limited to have only 4 CS managed, now it is possible to have
in the same time until 3 internal CS and no more limit for the CS
GPIO.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-7-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As platform_get_irq_byname() now prints an error when the interrupt
does not exist, scary warnings may be printed for optional interrupts:
renesas_spi e6b10000.spi: IRQ rx not found
renesas_spi e6b10000.spi: IRQ mux not found
Fix this by calling platform_get_irq_byname_optional() instead.
Remove the no longer needed printing of platform_get_irq errors, as the
remaining calls to platform_get_irq() and platform_get_irq_byname() take
care of that.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20191016143101.28738-1-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Until a few years ago, this driver was only used with CS GPIO. The
only exception is CS0 on AT91RM9200 which has to use internal CS. A
limitation of the internal CS is that they don't support CS High.
So by using the CS GPIO the CS high configuration was available except
for the particular case CS0 on RM9200.
When the support for the internal chip-select was added, the check of
the CS high support was not updated. Due to this the driver accepts
this configuration for all the SPI controller v2 (used by all SoCs
excepting the AT91RM9200) whereas the hardware doesn't support it for
infernal CS.
This patch fixes the test to match the hardware capabilities.
Fixes: 4820303480 ("spi: atmel: add support for the internal chip-select of the spi controller")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-3-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When improving the CS GPIO support at core level, the SPI_CS_HIGH
has been enabled for all the CS lines used for a given SPI controller.
However, the SPI framework allows to have on the same controller native
CS and GPIO CS. The native CS may not support the SPI_CS_HIGH, so they
should not be setup automatically.
With this patch the setting is done only for the CS that will use a
GPIO as CS
Fixes: f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191018152929.3287-1-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In DMA mode we have a maximum transfer size, past that the driver
falls back to PIO (see the check at the top of pxa2xx_spi_transfer_one).
Falling back to PIO for big transfers defeats the point of a dma engine,
hence set the max transfer size to inform spi clients that they need
to do something smarter.
This was uncovered by the drm_mipi_dbi spi panel code, which does
large spi transfers, but stopped splitting them after:
commit e143364b4c
Author: Noralf Trønnes <noralf@tronnes.org>
Date: Fri Jul 19 17:59:10 2019 +0200
drm/tinydrm: Remove tinydrm_spi_max_transfer_size()
After this commit the code relied on the spi core to split transfers
into max dma-able blocks, which also papered over the PIO fallback issue.
Fix this by setting the overall max transfer size to the DMA limit,
but only when the controller runs in DMA mode.
Fixes: e143364b4c ("drm/tinydrm: Remove tinydrm_spi_max_transfer_size()")
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Andy Shevchenko <andriy.shevchenko@intel.com>
Reported-and-tested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-spi@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://lore.kernel.org/r/20191017064426.30814-1-daniel.vetter@ffwll.ch
Signed-off-by: Mark Brown <broonie@kernel.org>
For many places in the spi drivers, using the new `spi_transfer_delay`
helper is straightforward.
It's just replacing:
```
if (t->delay_usecs)
udelay(t->delay_usecs);
```
with `spi_transfer_delay(t)` which handles both `delay_usecs` and the new
`delay` field.
This change replaces in all places (in the spi drivers) where this change
is simple.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-10-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This change implements CS control for setup, hold & inactive delays.
The `cs_setup` delay is completely new, and can help with cases where
asserting the CS, also brings the device out of power-sleep, where there
needs to be a longer (than usual), before transferring data.
The `cs_hold` time can overlap with the `delay` (or `delay_usecs`) from an
SPI transfer. The main difference is that `cs_hold` implies that CS will be
de-asserted.
The `cs_inactive` delay does not have a clear use-case yet. It has been
implemented mostly because the `spi_set_cs_timing()` function implements
it. To some degree, this could overlap or replace `cs_change_delay`, but
this will require more consideration/investigation in the future.
All these delays have been added to the `spi_controller` struct, as they
would typically be configured by calling `spi_set_cs_timing()` after an
`spi_setup()` call.
Software-mode for CS control, implies that the `set_cs_timing()` hook has
not been provided for the `spi_controller` object.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-16-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The initial version of `spi_set_cs_timing()` was implemented with
consideration only for clock-cycles as delay.
For cases like `CS setup` time, it's sometimes needed that micro-seconds
(or nano-seconds) are required, or sometimes even longer delays, for cases
where the device needs a little longer to start transferring that after CS
is asserted.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-15-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The `delay` field has type `struct spi_delay`.
This allows users to specify nano-second or clock-cycle delays (if needed).
Converting to use `delay` is straightforward: it's just assigning the
value to `delay.value` and hard-coding the `delay.unit` to
`SPI_DELAY_UNIT_USECS`.
This keeps the uapi for spidev un-changed. Changing it can be part of
another changeset and discussion.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-14-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This conversion to the spi_transfer_delay_exec() helper is not
straightforward, as it seems that when a delay is present, the controller
issues a command, and then a delay is followed.
This change adds support for the new `delay` field which is of type
`spi_delay` and keeps backwards compatibility with the old `delay_usecs`
field.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-12-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The tegra114 driver has a weird/separate `tegra_spi_transfer_delay()`
function that does 2 delays: one mdelay() and one udelay().
This was introduced via commit f4fade12d5
("spi/tegra114: Correct support for cs_change").
There doesn't seem to be a mention in that commit message to suggest a
specific need/use-case for having the 2 delay calls.
For the most part, udelay() should be sufficient.
This change replaces it with the new `spi_transfer_delay_exec()`, which
should do the same thing.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-11-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The change introduces the `delay` field to the `spi_transfer` struct as an
`struct spi_delay` type.
This intends to eventually replace `delay_usecs`.
But, since there are many users of `delay_usecs`, this needs some
intermediate work.
A helper called `spi_transfer_delay_exec()` is also added, which maintains
backwards compatibility with `delay_usecs`, by assigning the value to
`delay` if non-zero.
This should maintain backwards compatibility with current users of
`udelay_usecs`.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-9-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This change does a conversion from the `word_delay_usecs` -> `word_delay`
for the `spi_device` struct.
This allows users to specify inter-word delays in other unit types
(nano-seconds or clock cycles), depending on how users want.
The Atmel SPI driver is the only current user of the `word_delay_usecs`
field (from the `spi_device` struct).
So, it needed a slight conversion to use the `word_delay` as an `spi_delay`
struct.
In SPI core, the only required mechanism is to update the `word_delay`
information per `spi_transfer`. This requires a bit more logic than before,
because it needs that both delays be converted to a common unit
(nano-seconds) for comparison.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-8-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
