We no longer need the dma_caps since the dma driver
already clamps the burst length to the hardware limit,
so don't request and store dma_caps in device data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signal tx dma when spi fifo is less than half full,
and limit tx bursts to half the fifo length.
Clamp rx burst length to 1 to avoid alignment issues.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rxconf and txconf structs are allocated on the
stack, so make sure we zero them before filling out
the relevant fields.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
New driver for Qualcomm QuadSPI(QSPI) controller that is used to
communicate with slaves such as flash memory devices. The QSPI controller
can operate in 2 or 4 wire mode but only supports SPI Mode 0. The
controller can also operate in Single or Dual data rate modes.
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for a new devicetree compatible string called
'amazon,alpine-apb-ssi', which is necessary for the Amazon Alpine spi
controller. 'amazon,alpine-dw-apb-ssi' is used in the dw spi driver if
specified in the devicetree. Otherwise, fall back to driver default
behavior, i.e. original dw IP hw driver behavior.
Signed-off-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixing/optimizing bcm_qspi_bspi_read() performance introduced two
changes:
1) It added a loop to read all requested data using multiple BSPI ops.
2) It bumped max size of a single BSPI block request from 256 to 512 B.
The later change resulted in occasional BSPI timeouts causing a
regression.
For some unknown reason hardware doesn't always handle reads as expected
when using 512 B chunks. In such cases it may happen that BSPI returns
amount of requested bytes without the last 1-3 ones. It provides the
remaining bytes later but doesn't raise an interrupt until another LR
start.
Switching back to 256 B reads fixes that problem and regression.
Fixes: 345309fa7c ("spi: bcm-qspi: Fix bcm_qspi_bspi_read() performance")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
During implementation of the new API bcm_qspi_bspi_set_flex_mode() has
been modified breaking calculation of address length. An unnecessary
multiplication was added breaking flash reads.
Fixes: 5f195ee7d8 ("spi: bcm-qspi: Implement the spi_mem interface")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
spidev will make a big fuss if a device tree node binds a device by
using "spidev" as the node's compatible property.
However, the logic for this isn't looking for "spidev" in the
compatible, but rather checking that the device is NOT compatible with
spidev's list of devices.
This causes a false positive if a device not named "rohm,dh2228fv", etc.
binds to spidev, even if a means other than putting "spidev" in the
device tree was used. E.g., the sysfs driver_override attribute.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
This attribute works the same was as the identically named attribute
for PCI, AMBA, and platform devices. For reference, see:
commit 3cf3857134 ("ARM: 8256/1: driver coamba: add device binding
path 'driver_override'")
commit 3d713e0e38 ("driver core: platform: add device binding path
'driver_override'")
commit 782a985d7a ("PCI: Introduce new device binding path using
pci_dev.driver_override")
If the name of a driver is written to this attribute, then the device
will bind to the named driver and only the named driver.
The device will bind to the driver even if the driver does not list the
device in its id table. This behavior is different than the driver's
bind attribute, which only allows binding to devices that are listed as
supported by the driver.
It can be used to bind a generic driver, like spidev, to a device.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Certain devices don't work well when a transmit FIFO underrun or
receive FIFO overrun occurs. Example is the SAF400x radio chip when
running at high speed which leads to garbage being sent to/received from
the chip. In which case, it should stall waiting for further data to be
available before proceeding. This patch unset the NOSTALL bit in CFGR1
by default to prevent this issue.
Signed-off-by: Hieu Tran Dang <dangtranhieu2012@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clang warns when one enumerated type is implicitly converted to another.
drivers/spi/spi-ep93xx.c:342:62: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
nents = dma_map_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:428:58: note: expanded from macro
'dma_map_sg'
#define dma_map_sg(d, s, n, r) dma_map_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~ ^
drivers/spi/spi-ep93xx.c:348:57: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:429:62: note: expanded from macro
'dma_unmap_sg'
#define dma_unmap_sg(d, s, n, r) dma_unmap_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~~~ ^
drivers/spi/spi-ep93xx.c:377:56: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:429:62: note: expanded from macro
'dma_unmap_sg'
#define dma_unmap_sg(d, s, n, r) dma_unmap_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~~~ ^
3 warnings generated.
dma_{,un}map_sg expect an enum of type dma_data_direction but this
driver uses dma_transfer_direction for everything. Convert the driver to
use dma_data_direction for these two functions.
There are two places that strictly require an enum of type
dma_transfer_direction: the direction member in struct dma_slave_config
and the direction parameter in dmaengine_prep_slave_sg. To avoid using
an explicit cast, add a simple function, ep93xx_dma_data_to_trans_dir,
to safely map between the two types because they are not 1 to 1 in
meaning.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With this commit the DSPI driver on the BK4 board can be used for SPI
transmission managed from user space (via /dev/spidev0.0).
Example usage/testing:
insmod ./spi-fsl-dspi.ko
./spidev_test -D /dev/spidev0.0 -s 3000000 -v -H -b 8 -p "\xCC\x11\x22\x74"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rewrite switch code block to directly do the expected number
of shifts in each case and have break statements.
Addresses-Coverity-ID: 1056539 ("Missing break in switch")
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Apparently, this code does not actually fall through to the next case
because the machine restarts before it has a chance. However, for the
sake of maintenance and readability, we better add the missing break
statement.
Addresses-Coverity-ID: 1437892 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark writes:
"spi: Fixes for v4.19
Quite a few fixes for the Renesas drivers in here, plus a fix for the
Tegra driver and some documentation fixes for the recently added
spi-mem code. The Tegra fix is relatively large but fairly
straightforward and mechanical, it runs on probe so it's been
reasonably well covered in -next testing."
* tag 'spi-fix-v4.19-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-mem: Move the DMA-able constraint doc to the kerneldoc header
spi: spi-mem: Add missing description for data.nbytes field
spi: rspi: Fix interrupted DMA transfers
spi: rspi: Fix invalid SPI use during system suspend
spi: sh-msiof: Fix handling of write value for SISTR register
spi: sh-msiof: Fix invalid SPI use during system suspend
spi: gpio: Fix copy-and-paste error
spi: tegra20-slink: explicitly enable/disable clock
The of_find_spi_device_by_node() helper function is useful for other
modules too. Export the funciton as GPL like all other spi helper
functions and make it available if CONFIG_OF is enabled, because it isn't
related to the CONFIG_OF_DYNAMIC context. Finally add a stub if
CONFIG_OF isn't enabled, so others must not care about it.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the appropriate SPDX license identifier and drop the previous
license text.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
On r8a7791/koelsch:
m25p80 spi0.0: error -22 reading 9f
m25p80: probe of spi0.0 failed with error -22
Apparently the logic in spi_mem_check_op() is wrong, rejecting the
spi-mem operation if any buswidth is valid, instead of invalid.
Fixes: 380583227c ("spi: spi-mem: Add extra sanity checks on the op param")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The __exit section is left out for built-in drivers, so a
'remove' callback must not be marked as such to avoid breaking when
we unbind a device at runtime. This was pointed out by kbuild:
`sprd_spi_remove' referenced in section `.data' of drivers/spi/spi-sprd.o: defined in discarded section `.exit.text' of drivers/spi/spi-sprd.o
Fixes: e7d973a31c ("spi: sprd: Add SPI driver for Spreadtrum SC9860")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clang warns when one enumerated type is converted implicitly to another:
drivers/spi/spi-pic32.c:323:8: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
DMA_FROM_DEVICE,
^~~~~~~~~~~~~~~
drivers/spi/spi-pic32.c:333:8: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
DMA_TO_DEVICE,
^~~~~~~~~~~~~
2 warnings generated.
Use the proper enums from dma_transfer_direction (DMA_FROM_DEVICE =
DMA_DEV_TO_MEM = 2, DMA_TO_DEVICE = DMA_MEM_TO_DEV = 1) to satify Clang.
Link: https://github.com/ClangBuiltLinux/linux/issues/159
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some combinations are simply not valid and should be rejected before
the op is passed to the SPI controller driver.
Add an spi_mem_check_op() helper and use it in spi_mem_exec_op() and
spi_mem_supports_op() to make sure the spi-mem operation is valid.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This remove the check and subsequent return of error for the case when
a SPI device requires SPI_CS_WORD and is also configured to use a GPIO
for the CS line.
Commit a134cc414e86 ("spi: always use software fallback for SPI_CS_WORD
when using cs_gio") handles this case now, so this check is no longer
necessary.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This modifies the condition for using the software fallback
implementation for SPI_CS_WORD when the SPI controller is using a GPIO
for the CS line. When using a GPIO for CS, the hardware implementation
won't work, so we just enable the software fallback globally in this
case.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mediatek SPI driver modifies some fields (tx_buf, rx_buf, len, tx_dma,
rx_dma) of the spi_transfer* passed in when doing transfer_one and in
interrupt handler. This is somewhat unexpected, and there are some
caller (e.g. Cr50 spi driver) that reuse the spi_transfer for multiple
messages. Add a field to record how many bytes have been transferred,
and calculate the right len / buffer based on it instead.
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Change-Id: I23e218cd964f16c0b2b26127d4a5ca6529867673
Signed-off-by: Mark Brown <broonie@kernel.org>
If the pll clock needs to be enabled to get its rate, it will also need
to be enabled to provide it. So ensure it is kept enabled through the
lifetime of the device.
Fixes: 0d7412ed1f ("spi/bcm63xx-hspi: Enable the clock before calling clk_get_rate().")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It makes no sense to remove the device on shutdown. And it break things
when the hardware crucial for shutdown (such as the embedded controller)
is attached to the SPI bus.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for the SPI_CS_WORD flag to the TI DaVinci SPI
driver. This mode can be used as long as we are using the hardware
chip select and not a GPIO chip select.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds a default software implementation for the SPI_CS_WORD flag for
controllers that don't have such a feature.
The SPI_CS_WORD flag indicates that the CS line should be toggled
between each word sent, not just between each transfer. The
implementation works by using existing functions to split transfers into
one-word-sized transfers and sets the cs_change bit for each of the
new transfers.
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark writes:
"spi: Fixes for v4.19
As well as one driver fix there's a couple of fixes here which address
issues with the use of IDRs for allocation of dynamic bus numbers,
ensuring that dynamic bus numbers interact well with static bus numbers
assigned via DT and otherwise."
* tag 'spi-fix-v4.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-fsl-dspi: fix broken DSPI_EOQ_MODE
spi: Fix double IDR allocation with DT aliases
spi: fix IDR collision on systems with both fixed and dynamic SPI bus numbers
Almost all spi drivers assign spi master->dev.of_node from
its parent platform device without additional refcounting.
It seems of_node_get() in pic32_sqi_probe() is unnecessary
and there is no corresponding of_node_put().
Found by Linux Driver Verification project (linuxtesting.org)
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-davinci.c: In function 'davinci_spi_setup':
drivers/spi/spi-davinci.c:422:36: warning:
variable 'pdata' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DaVinci SPI can use either:
- Internal chip selects (inside the SPI host)
- External chip selects (using GPIO)
- External chip selects passed in pdata
The last way of passing external chip selects through
platform data is not used in the kernel. Delete it to make
the code simpler when refactoring GPIO.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Michele Dionisio <michele.dionisio@gmail.com>
Cc: Frode Isaksen <fisaksen@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need that to adjust the len of the 2nd transfer (called data in
spi-mem) if it's too long to fit in a SPI message or SPI transfer.
Fixes: c36ff266dc ("spi: Extend the core to ease integration of SPI memory controllers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the driver for at91-usart in spi mode. The USART IP can be configured
to work in many modes and one of them is SPI.
The driver was tested on sama5d3-xplained and sama5d4-xplained boards with
enc28j60 ethernet controller as slave.
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviwed-by: Mark Brown <broonie@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is a logical problem in spi-gpio with host just
assigning a MOSI line and no MISO: this is interpreted
as the host cannot do RX and the host is flagged with
SPI_MASTER_NO_RX.
This is wrong: since GPIO lines can switch direction,
in 3WIRE operation the host will simply reverse the
direction of the GPIO line and start reading from it,
there is even code for doing this in the driver, but
it went unnoticed because it was tested by using a
master with 4 wires but a device using just 3 wires.
Remove the offending flag.
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Almost all spi drivers assign spi master->dev.of_node from
its parent platform device without additional refcounting.
It seems of_node_get() in pic32_spi_probe() is unnecessary
and there is no corresponding of_node_put().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-pl022.c: In function 'do_polling_transfer':
drivers/spi/spi-pl022.c:1493:20: warning:
variable 'chip' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-dw driver currently only supports 8 or 16 bits per word.
Since the hardware supports 4-16 bits per word, adapt the driver
to also support this.
Tested on socfpga cyclone5 with a 9-bit SPI display.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-gpio.c: In function 'spi_gpio_remove':
drivers/spi/spi-gpio.c:450:33: warning:
variable 'pdata' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When interrupted, wait_event_interruptible_timeout() returns
-ERESTARTSYS, and the SPI transfer in progress will fail, as expected:
m25p80 spi0.0: SPI transfer failed: -512
spi_master spi0: failed to transfer one message from queue
However, as the underlying DMA transfers may not have completed, all
subsequent SPI transfers may start to fail:
spi_master spi0: receive timeout
qspi_transfer_out_in() returned -110
m25p80 spi0.0: SPI transfer failed: -110
spi_master spi0: failed to transfer one message from queue
Fix this by calling dmaengine_terminate_all() not only for timeouts, but
also for errors.
This can be reproduced on r8a7991/koelsch, using "hd /dev/mtd0" followed
by CTRL-C.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
If the SPI queue is running during system suspend, the system may lock
up.
Fix this by stopping/restarting the queue during system suspend/resume,
by calling spi_master_suspend()/spi_master_resume() from the PM
callbacks. In-kernel users will receive an -ESHUTDOWN error while
system suspend/resume is in progress.
Based on a patch for sh-msiof by Gaku Inami.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch changes writing to the SISTR register according to the H/W
user's manual.
The TDREQ bit and RDREQ bits of SISTR are read-only, and must be written
their initial values of zero.
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
[geert: reword]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
If the SPI queue is running during system suspend, the system may lock
up.
Fix this by stopping/restarting the queue during system suspend/resume
by calling spi_master_suspend()/spi_master_resume() from the PM
callbacks. In-kernel users will receive an -ESHUTDOWN error while
system suspend/resume is in progress.
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
[geert: Cleanup, reword]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
spi_controller_{suspend,resume}() already prints an error message on
failure, so there is no need to repeat this in individual drivers.
Note: spi_master_{suspend,resume}() is an alias for
spi_controller_{suspend,resume}().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Daniel Mack <daniel@zonque.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes an embarrassing copy-and-paste error in the
errorpath of spi_gpio_request(): we were checking the wrong
struct member for error code right after retrieveing the
sck GPIO.
Fixes: 9b00bc7b90 ("spi: spi-gpio: Rewrite to use GPIO descriptors")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change increases the source code readability.
Instead of using `spi->child[cs].direct_access.XXX` use `dir_acc->XXX`.
Instead of using `orion_spi->child[cs].direct_access.vaddr` use `vaddr`.
Signed-off-by: Kosta Zertsekel <zertsekel@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
