[Why]
We need to update TTU properly if DRAMClockChangeWatermark changes. If
TTU < DRAMClockChangeWatermark, we pstate won't be allowed and we will
hang in some PSR cases.
[How]
Update TTU if DramClockChangeWatermark value increases (only if TTU was
dependent on the watermark value on the DRAMClockChangeWatermark value
in the first place).
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
RV2 and variants are indistinguishable by hw internal rev alone, need to
be distinguishable in order to correctly set max vlevel. Previous
detection change incorrectly checked for hw internal rev.
[HOW]
Use pci revision to check if RV2 or low power variant Correct a few
overlapping ASICREV range checks
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Michael Strauss <Michael.Strauss@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DalMPVisualConfirm does not support FreeSync 2 ARGB2101010 which causes
black visual confirm bar when playing HDR video on FreeSync 2 display in
full screen mode
[How]
Added pink color for DalMPVisualConfirm on FreeSync 2 ARGB2101010
surface
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some displays clear ignore MSA bit on mode change, which cause
blackscreen when programming variable vtotals. Ignore MSA bit needs
programming needs to be delayed or re-set to be retained.
[How]
Create patch to delay programming ignore MSA bit after unblanking
stream.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A software workaround is required for all vendor-built cards on platform.
[How]
When performing DP link training, we must send TPS1 before DPCD:100h is
written with the proper bit rate value. This change must be applies in
ALL cases when LT happens.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Firmware state helps to debug sequence issues and hangs for DMCUB
commands and we don't have an easy mechanism to dump it from the driver.
[How]
Add a debugfs entry to dump the current firmware state.
Example usage:
cat /sys/kernel/debug/dri/0/amdgpu_dm_dmub_fw_state
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently DAL programs negative slope for the last point of output
transfer function curve.
[How]
Applying a check for the last PWL point for RGB values not to be
smaller than previous. If smaller, initialize the last point values
to a sum of previous PWL value and previous PWL delta;
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are some structures and functions meant only to be used in the
scope of that single rn_clk_mgr c file.
[How]
Make structs and funcs static if only meant to be used within
rn_clk_mgr
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Make panel backlight and power on/off functions into
hardware specific function pointers
[How]
Add function pointers for panel related hw functions
- is_panel_powered_on
- is_panel_backlight_on
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When calculating nominal refresh rates, don't round.
Only the VSIF needs to be rounded.
[How]
Revert rounding change for nominal and just round when forming the
FreeSync VSIF.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Unused VMIDs were not evicted correctly
[How]
1. evict_vmids() logic was fixed;
2. Added boundary check for add_ptb_to_table() and
clear_entry_from_vmid_table() to avoid crash caused by array out of
boundary;
3. For mod_vmid_get_for_ptb(), vimd is changed from unsigned to signed
due to vimd is signed.
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Add optimization to allow pstate change support when all displays
are off in DCN2.
[How]
Add clk_mgr_helper_get_active_plane_cnt() to sum plane_count for all
valid stream_status[]. If plane_count is 0, then there are no active
or virtual streams present. Use plane_count == 0 as extra condition to
enable p_state_change_support in dcn2_update_clocks().
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If we're doing backdoor load then do it entirely ourselves without
invoking any of the frontdoor path to avoid potential issues with
outdated tOS.
[How]
Check the load type and don't pass it to base if we don't want it
loaded.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When we execute the first command for ASIC_INIT for command table
offloading we can hit a timing scenario such that the interrupts
for the inbox wptr haven't been enabled yet and the first command
is ignored until the second command is sent.
[How]
This happens when either the SCRATCH0 is already the correct status
code or autoload check is unsupported.
Clear SCRATCH0 during reset.
Also ensure that we don't accidentally reset the ASIC again in case
of a hang by clearing GPINT while we're at it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
According to HW team, PG is dropped for NV12, but programming
the registers will still cause power to be consumed, so don't
program for NV12.
[How]
Set function pointer to NULL if NV12
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently there is a minor error in scaling filter coefficients
caused by truncation to fit the HW registers.This error accummulates
with increased taps, but has gone unnoticed due to vast majority of
scaling being done with only 4 taps.
Scaling filters are now updated using HW team's filter generator
which has quantization error minimization built in.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
core_link_read_dpcd() will invoke dm_helpers_dp_read_dpcd(),
which needs to read dpcd info with the help of aconnector.
If aconnector (dc->links[i]->prev) is NULL, then dpcd status
cannot be read.
As a result, dpcd read fails and a line of error will be
printed out in dmesg.log as:
"*ERROR* Failed to found connector for link!"
[How]
Make sure that aconnector (dc->links[i]->prev) is not NULL,
then read dpcd status.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Joseph Gravenor <Joseph.Gravenor@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Using a heavy-weight TLB flush once is not sufficient. Concurrent
memory accesses in the same TLB cache line can re-populate TLB entries
from stale texture cache (TC) entries while the heavy-weight TLB
flush is in progress. To fix this race condition, perform another TLB
flush after the heavy-weight one, when TC is known to be clean.
Move the workaround into the low-level TLB flushing functions. This way
they apply to amdgpu as well, and KIQ-based TLB flush only needs to
synchronize once.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: shaoyun liu <shaoyun.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
what:
some os preemption path is messed up with world switch preemption
fix:
cleanup those logics so os preemption not mixed with world switch
this patch is a general fix for issues comes from SRIOV MCBP, but
there is still UMD side issues not resovlved yet, so this patch
cannot fix all world switch bug.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1)
we shouldn't load PSP kdb and sys/sos for VF, they are
supposed to be handled by hypervisor
2)
ih reroute doesn't work on VF thus we should avoid calling
it, besides VF should not use those PSP register sets for PF
3)
shouldn't load SMU ucode under SRIOV, otherwise PSP would report
error
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Propagate bus format/flags so that the previous bridge element in the
chain knows which input format the panel bridge expects.
v11:
* Fix a typo in the subject
* Update the commit message so it's readable by itself
v10:
* Add changelog to the commit message
v8 -> v9:
* No changes
v7:
* Set atomic state hooks explicitly
v4 -> v6:
* Not part of the series
v3:
* Adjust things to match the new bus-format negotiation approach
* Use drm_atomic_helper_bridge_propagate_bus_fmt
* Don't implement ->atomic_check() (the core now takes care of bus
flags propagation)
v2:
* Adjust things to match the new bus-format negotiation approach
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128135514.108171-11-boris.brezillon@collabora.com
The larb device remains NULL if the type is MTK_DISP_OVL_2L.
A kernel panic is raised when a crtc uses mtk_smi_larb_get or
mtk_smi_larb_put.
Fixes: b17bdd0d7a ("drm/mediatek: add component OVL_2L0")
Signed-off-by: Phong LE <ple@baylibre.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
