This adds IRQ_HARD_DIS to irq_happened. Although it doesn't seem to
matter much because we're not allowed to enable irqs in an NMI
handler, the soft-irq debugging code is becoming more strict about
ensuring IRQ_HARD_DIS is in sync with MSR[EE], this may help avoid
asserts or other issues.
Add a comment explaining why MCE does not have this. Early machine
check is generally much smaller and more contained code which will
explode if you look at it wrong anyway as it runs in real mode, though
there's an argument that we should do similar reconciling for the MCE
as well.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200225173541.1549955-22-npiggin@gmail.com
Apart from SRESET, MCE, and syscall (hcall variant), the SRR type
interrupts are not escalated to hypervisor mode, so are delivered to
the OS.
When running PR KVM, the OS is the hypervisor, and the guest runs with
MSR[PR]=1 (ie. usermode), so these interrupts must test if a guest was
running when interrupted. These tests are required at the real-mode
entry points because the PR KVM host runs with LPCR[AIL]=0.
In HV KVM and nested HV KVM, the guest always receives these
interrupts, so there is no need for the host to make this test. So
remove the tests if PR KVM is not configured.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200225173541.1549955-21-npiggin@gmail.com
The hdec interrupt handler is reported to sometimes fire in Linux if
KVM leaves it pending after a guest exists. This is harmless, so there
is a no-op handler for it.
The interrupt handler currently uses the regular kernel stack. Change
this to avoid touching the stack entirely.
This should be the last place where the regular Linux stack can be
accessed with asynchronous interrupts (including PMI) soft-masked.
It might be possible to take advantage of this invariant, e.g., to
context switch the kernel stack SLB entry without clearing MSR[EE].
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200225173541.1549955-17-npiggin@gmail.com
Replace IEARLY=1 and IEARLY=2 with IBRANCH_COMMON, which controls if
the entry code branches to a common handler; and IREALMODE_COMMON,
which controls whether the common handler should remain in real mode.
These special cases no longer avoid loading the SRR registers, there
is no point as most of them load the registers immediately anyway.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200225173541.1549955-14-npiggin@gmail.com
This allows more code to be moved out of unrelocated regions. The
system call KVMTEST is changed to be open-coded and remain in the
tramp area to avoid having to move it to entry_64.S. The custom nature
of the system call entry code means the hcall case can be made more
streamlined than regular interrupt handlers.
mpe: Incorporate fix from Nick:
Moving KVM test to the common entry code missed the case of HMI and
MCE, which do not do __GEN_COMMON_ENTRY (because they don't want to
switch to virt mode).
This means a MCE or HMI exception that is taken while KVM is running a
guest context will not be switched out of that context, and KVM won't
be notified. Found by running sigfuz in guest with patched host on
POWER9 DD2.3, which causes some TM related HMI interrupts (which are
expected and supposed to be handled by KVM).
This fix adds a __GEN_REALMODE_COMMON_ENTRY for those handlers to add
the KVM test. This makes them look a little more like other handlers
that all use __GEN_COMMON_ENTRY.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200225173541.1549955-13-npiggin@gmail.com
The real mode interrupt entry points currently use rfid to branch to
the common handler in virtual mode. This is a significant amount of
code, and forces other code (notably the KVM test) to live in the
real mode handler.
In the interest of minimising the amount of code that runs unrelocated
move the switch to virt mode into the common code, and do it with
mtmsrd, which avoids clobbering SRRs (although the post-KVMTEST
performance of real-mode interrupt handlers is not a big concern these
days).
This requires CTR to always be saved (real-mode needs to reach 0xc...)
but that's not a huge impact these days. It could be optimized away in
future.
mpe: Incorporate fix from Nick:
It's possible for interrupts to be replayed when TM is enabled and
suspended, for example rt_sigreturn, where the mtmsrd MSR_KERNEL in
the real-mode entry point to the common handler causes a TM Bad Thing
exception (due to attempting to clear suspended).
The fix for this is to have replay interrupts go to the _virt entry
point and skip the mtmsrd, which matches what happens before this
patch.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200225173541.1549955-11-npiggin@gmail.com
The code generation macro arguments are difficult to read, and
defaults can't easily be used.
This introduces a block where parameters can be set for interrupt
handler code generation by the subsequent macros, and adds the first
generation macro for interrupt entry.
One interrupt handler is converted to the new macros to demonstrate
the change, the rest will be coverted all at once.
No generated code change.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200225173541.1549955-2-npiggin@gmail.com
In restore_tm_sigcontexts() we take the trap value directly from the
user sigcontext with no checking:
err |= __get_user(regs->trap, &sc->gp_regs[PT_TRAP]);
This means we can be in the kernel with an arbitrary regs->trap value.
Although that's not immediately problematic, there is a risk we could
trigger one of the uses of CHECK_FULL_REGS():
#define CHECK_FULL_REGS(regs) BUG_ON(regs->trap & 1)
It can also cause us to unnecessarily save non-volatile GPRs again in
save_nvgprs(), which shouldn't be problematic but is still wrong.
It's also possible it could trick the syscall restart machinery, which
relies on regs->trap not being == 0xc00 (see 9a81c16b52 ("powerpc:
fix double syscall restarts")), though I haven't been able to make
that happen.
Finally it doesn't match the behaviour of the non-TM case, in
restore_sigcontext() which zeroes regs->trap.
So change restore_tm_sigcontexts() to zero regs->trap.
This was discovered while testing Nick's upcoming rewrite of the
syscall entry path. In that series the call to save_nvgprs() prior to
signal handling (do_notify_resume()) is removed, which leaves the
low-bit of regs->trap uncleared which can then trigger the FULL_REGS()
WARNs in setup_tm_sigcontexts().
Fixes: 2b0a576d15 ("powerpc: Add new transactional memory state to the signal context")
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200401023836.3286664-1-mpe@ellerman.id.au
Every remaining user just has the error case returning -EFAULT.
In fact, the exception was __get_user_asm_nozero(), which was removed in
commit 4b842e4e25 ("x86: get rid of small constant size cases in
raw_copy_{to,from}_user()"), and the other __get_user_xyz() macros just
followed suit for consistency.
Fix up some macro whitespace while at it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The last user was removed by commit 4b842e4e25 ("x86: get rid of small
constant size cases in raw_copy_{to,from}_user()"). Get rid of the
left-overs before somebody tries to use it again.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
Pull tty/serial updates from Greg KH:
"Here is the big set of TTY / Serial patches for 5.7-rc1
Lots of console fixups and reworking in here, serial core tweaks
(doesn't that ever get old, why are we still creating new serial
devices?), serial driver updates, line-protocol driver updates, and
some vt cleanups and fixes included in here as well.
All have been in linux-next with no reported issues"
* tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (161 commits)
serial: 8250: Optimize irq enable after console write
serial: 8250: Fix rs485 delay after console write
vt: vt_ioctl: fix use-after-free in vt_in_use()
vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use virtual console
tty: serial: make SERIAL_SPRD depend on COMMON_CLK
tty: serial: fsl_lpuart: fix return value checking
tty: serial: fsl_lpuart: move dma_request_chan()
ARM: dts: tango4: Make /serial compatible with ns16550a
ARM: dts: mmp*: Make the serial ports compatible with xscale-uart
ARM: dts: mmp*: Fix serial port names
ARM: dts: mmp2-brownstone: Don't redeclare phandle references
ARM: dts: pxa*: Make the serial ports compatible with xscale-uart
ARM: dts: pxa*: Fix serial port names
ARM: dts: pxa*: Don't redeclare phandle references
serial: omap: drop unused dt-bindings header
serial: 8250: 8250_omap: Add DMA support for UARTs on K3 SoCs
serial: 8250: 8250_omap: Work around errata causing spurious IRQs with DMA
serial: 8250: 8250_omap: Extend driver data to pass FIFO trigger info
serial: 8250: 8250_omap: Move locking out from __dma_rx_do_complete()
serial: 8250: 8250_omap: Account for data in flight during DMA teardown
...
Pull Kbuild updates from Masahiro Yamada:
"Build system:
- add CONFIG_UNUSED_KSYMS_WHITELIST, which will be useful to define a
fixed set of export symbols for Generic Kernel Image (GKI)
- allow to run 'make dt_binding_check' without .config
- use full schema for checking DT examples in *.yaml files
- make modpost fail for missing MODULE_IMPORT_NS(), which makes more
sense because we know the produced modules are never loadable
- Remove unused 'AS' variable
Kconfig:
- sanitize DEFCONFIG_LIST, and remove ARCH_DEFCONFIG from Kconfig
files
- relax the 'imply' behavior so that symbols implied by 'y' can
become 'm'
- make 'imply' obey 'depends on' in order to make 'imply' really weak
Misc:
- add documentation on building the kernel with Clang/LLVM
- revive __HAVE_ARCH_STRLEN for 32bit sparc to use optimized strlen()
- fix warning from deb-pkg builds when CONFIG_DEBUG_INFO=n
- various script and Makefile cleanups"
* tag 'kbuild-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (34 commits)
Makefile: Update kselftest help information
kbuild: deb-pkg: fix warning when CONFIG_DEBUG_INFO is unset
kbuild: add outputmakefile to no-dot-config-targets
kbuild: remove AS variable
net: wan: wanxl: refactor the firmware rebuild rule
net: wan: wanxl: use $(M68KCC) instead of $(M68KAS) for rebuilding firmware
net: wan: wanxl: use allow to pass CROSS_COMPILE_M68k for rebuilding firmware
kbuild: add comment about grouped target
kbuild: add -Wall to KBUILD_HOSTCXXFLAGS
kconfig: remove unused variable in qconf.cc
sparc: revive __HAVE_ARCH_STRLEN for 32bit sparc
kbuild: refactor Makefile.dtbinst more
kbuild: compute the dtbs_install destination more simply
Makefile: disallow data races on gcc-10 as well
kconfig: make 'imply' obey the direct dependency
kconfig: allow symbols implied by y to become m
net: drop_monitor: use IS_REACHABLE() to guard net_dm_hw_report()
modpost: return error if module is missing ns imports and MODULE_ALLOW_MISSING_NAMESPACE_IMPORTS=n
modpost: rework and consolidate logging interface
kbuild: allow to run dt_binding_check without kernel configuration
...
Currently, kernel shows the below values
"persistence_domain":"cpu_cache"
"persistence_domain":"memory_controller"
"persistence_domain":"unknown"
"cpu_cache" indicates no extra instructions is needed to ensure the persistence
of data in the pmem media on power failure.
"memory_controller" indicates cpu cache flush instructions are required to flush
the data. Platform provides mechanisms to automatically flush outstanding
write data from memory controler to pmem on system power loss.
Based on the above use memory_controller for non volatile regions on ppc64.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Link: https://lore.kernel.org/r/20200324034821.60869-1-aneesh.kumar@linux.ibm.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pull x86 vmware updates from Ingo Molnar:
"The main change in this tree is the addition of 'steal time clock
support' for VMware guests"
* 'x86-vmware-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vmware: Use bool type for vmw_sched_clock
x86/vmware: Enable steal time accounting
x86/vmware: Add steal time clock support for VMware guests
x86/vmware: Remove vmware_sched_clock_setup()
x86/vmware: Make vmware_select_hypercall() __init
Pull x86 mm updates from Ingo Molnar:
"A handful of changes:
- two memory encryption related fixes
- don't display the kernel's virtual memory layout plaintext on
32-bit kernels either
- two simplifications"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Remove the now redundant N_MEMORY check
dma-mapping: Fix dma_pgprot() for unencrypted coherent pages
x86: Don't let pgprot_modify() change the page encryption bit
x86/mm/kmmio: Use this_cpu_ptr() instead get_cpu_var() for kmmio_ctx
x86/mm/init/32: Stop printing the virtual memory layout
Pull misc x86 updates from Ingo Molnar:
- extend the decoder maps with CET instructions
- fix !vDSO corner cases
* 'x86-misc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/tests: Add CET instructions to the new instructions test
x86/insn: Add Control-flow Enforcement (CET) instructions to the opcode map
selftests/x86/ptrace_syscall_32: Fix no-vDSO segfault
selftests/x86/vdso: Fix no-vDSO segfaults
Currently, all harts have to jump Linux in RISC-V. This complicates the
multi-stage boot process as every transient stage also has to ensure all
harts enter to that stage and jump to Linux afterwards. It also obstructs
a clean Kexec implementation.
SBI HSM extension provides alternate solutions where only a single hart
need to boot and enter Linux. The booting hart can bring up secondary
harts one by one afterwards.
Add SBI HSM based cpu_ops that implements an ordered booting method in
RISC-V. This change is also backward compatible with older firmware not
implementing HSM extension. If a latest kernel is used with older
firmware, it will continue to use the default spinning booting method.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Pull x86 fpu updates from Ingo Molnar:
"Misc changes:
- add a pkey sanity check
- three commits to improve and future-proof xstate/xfeature handling
some more"
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pkeys: Add check for pkey "overflow"
x86/fpu/xstate: Warn when checking alignment of disabled xfeatures
x86/fpu/xstate: Fix XSAVES offsets in setup_xstate_comp()
x86/fpu/xstate: Fix last_good_offset in setup_xstate_features()
All SBI related extensions will not be implemented in sbi.c to avoid
bloating. Thus, sbi_err_map_linux_errno() will be used in other files
implementing that specific extension.
Export the function so that it can be used later.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Currently, all non-booting harts start booting after the booting hart
updates the per-hart stack pointer. This is done in a way that, it's
difficult to implement any other booting method without breaking the
backward compatibility.
Define a cpu_ops method that allows to introduce other booting methods
in future. Modify the current booting method to be compatible with
cpu_ops.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
The secondary hart booting and relocation code are under .init section.
As a result, it will be freed once kernel booting is done. However,
ordered booting protocol and CPU hotplug always requires these functions
to be present to bringup harts after initial kernel boot.
Move the required functions to a different section and make sure that
they are in memory within first 2MB offset as trampoline page directory
only maps first 2MB.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Few v0.1 SBI calls are being replaced by new SBI calls that follows v0.2
calling convention.
Implement the replacement extensions and few additional new SBI function calls
that makes way for a better SBI interface in future.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
We now have SBI v0.2 which is more scalable and extendable to handle
future needs for RISC-V supervisor interfaces.
Introduce a new config and move all SBI v0.1 code under that config.
This allows to implement the new replacement SBI extensions cleanly
and remove v0.1 extensions easily in future. Currently, the config
is enabled by default. Once all M-mode software, with v0.1, is no
longer in use, this config option and all relevant code can be easily
removed.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Few v0.1 SBI calls are being replaced by new SBI calls that follows
v0.2 calling convention.
This patch just defines these new extensions.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
The SBI v0.2 introduces a base extension which is backward compatible
with v0.1. Implement all helper functions and minimum required SBI
calls from v0.2 for now. All other base extension function will be
added later as per need.
As v0.2 calling convention is backward compatible with v0.1, remove
the v0.1 helper functions and just use v0.2 calling convention.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
As per the new SBI specification, current SBI implementation version
is defined as 0.1 and will be removed/replaced in future. Each of the
function call in 0.1 is defined as a separate extension which makes
easier to replace them one at a time.
Rename existing implementation to reflect that. This patch is just
a preparatory patch for SBI v0.2 and doesn't introduce any functional
changes.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Pull x86 cleanups from Ingo Molnar:
"This topic tree contains more commits than usual:
- most of it are uaccess cleanups/reorganization by Al
- there's a bunch of prototype declaration (--Wmissing-prototypes)
cleanups
- misc other cleanups all around the map"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
x86/mm/set_memory: Fix -Wmissing-prototypes warnings
x86/efi: Add a prototype for efi_arch_mem_reserve()
x86/mm: Mark setup_emu2phys_nid() static
x86/jump_label: Move 'inline' keyword placement
x86/platform/uv: Add a missing prototype for uv_bau_message_interrupt()
kill uaccess_try()
x86: unsafe_put-style macro for sigmask
x86: x32_setup_rt_frame(): consolidate uaccess areas
x86: __setup_rt_frame(): consolidate uaccess areas
x86: __setup_frame(): consolidate uaccess areas
x86: setup_sigcontext(): list user_access_{begin,end}() into callers
x86: get rid of put_user_try in __setup_rt_frame() (both 32bit and 64bit)
x86: ia32_setup_rt_frame(): consolidate uaccess areas
x86: ia32_setup_frame(): consolidate uaccess areas
x86: ia32_setup_sigcontext(): lift user_access_{begin,end}() into the callers
x86/alternatives: Mark text_poke_loc_init() static
x86/cpu: Fix a -Wmissing-prototypes warning for init_ia32_feat_ctl()
x86/mm: Drop pud_mknotpresent()
x86: Replace setup_irq() by request_irq()
x86/configs: Slightly reduce defconfigs
...
Pull x86 build updates from Ingo Molnar:
"A handful of updates: two linker script cleanups and a stock
defconfig+allmodconfig bootability fix"
* 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vdso: Discard .note.gnu.property sections in vDSO
x86, vmlinux.lds: Add RUNTIME_DISCARD_EXIT to generic DISCARDS
x86/Kconfig: Make CMDLINE_OVERRIDE depend on non-empty CMDLINE
Pull x86 boot updates from Ingo Molnar:
"Misc cleanups and small enhancements all around the map"
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot/compressed: Fix debug_puthex() parameter type
x86/setup: Fix static memory detection
x86/vmlinux: Drop unneeded linker script discard of .eh_frame
x86/*/Makefile: Use -fno-asynchronous-unwind-tables to suppress .eh_frame sections
x86/boot/compressed: Remove .eh_frame section from bzImage
x86/boot/compressed/64: Remove .bss/.pgtable from bzImage
x86/boot/compressed/64: Use 32-bit (zero-extended) MOV for z_output_len
x86/boot/compressed/64: Use LEA to initialize boot stack pointer
Pull arm64 updates from Catalin Marinas:
"The bulk is in-kernel pointer authentication, activity monitors and
lots of asm symbol annotations. I also queued the sys_mremap() patch
commenting the asymmetry in the address untagging.
Summary:
- In-kernel Pointer Authentication support (previously only offered
to user space).
- ARM Activity Monitors (AMU) extension support allowing better CPU
utilisation numbers for the scheduler (frequency invariance).
- Memory hot-remove support for arm64.
- Lots of asm annotations (SYM_*) in preparation for the in-kernel
Branch Target Identification (BTI) support.
- arm64 perf updates: ARMv8.5-PMU 64-bit counters, refactoring the
PMU init callbacks, support for new DT compatibles.
- IPv6 header checksum optimisation.
- Fixes: SDEI (software delegated exception interface) double-lock on
hibernate with shared events.
- Minor clean-ups and refactoring: cpu_ops accessor,
cpu_do_switch_mm() converted to C, cpufeature finalisation helper.
- sys_mremap() comment explaining the asymmetric address untagging
behaviour"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (81 commits)
mm/mremap: Add comment explaining the untagging behaviour of mremap()
arm64: head: Convert install_el2_stub to SYM_INNER_LABEL
arm64: Introduce get_cpu_ops() helper function
arm64: Rename cpu_read_ops() to init_cpu_ops()
arm64: Declare ACPI parking protocol CPU operation if needed
arm64: move kimage_vaddr to .rodata
arm64: use mov_q instead of literal ldr
arm64: Kconfig: verify binutils support for ARM64_PTR_AUTH
lkdtm: arm64: test kernel pointer authentication
arm64: compile the kernel with ptrauth return address signing
kconfig: Add support for 'as-option'
arm64: suspend: restore the kernel ptrauth keys
arm64: __show_regs: strip PAC from lr in printk
arm64: unwind: strip PAC from kernel addresses
arm64: mask PAC bits of __builtin_return_address
arm64: initialize ptrauth keys for kernel booting task
arm64: initialize and switch ptrauth kernel keys
arm64: enable ptrauth earlier
arm64: cpufeature: handle conflicts based on capability
arm64: cpufeature: Move cpu capability helpers inside C file
...
Pull microblaze updates from Michal Simek:
- convert license headers to SPDX
- cleanup header handling and use asm-generic one
- get rid of earlyprintk residues
- define barriers and use it in the code
- get rid of setup_irq() for timer
- various small addons and fixes
* tag 'microblaze-v5.7-rc1' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Replace setup_irq() by request_irq()
microblaze: Stop printing the virtual memory layout
microblaze: Use asm generic cmpxchg.h for !SMP case
microblaze: Define percpu sestion in linker file
microblaze: Remove unused boot_cpuid variable
microblaze: Add missing irqflags.h header
microblaze: Add sync to tlb operations
microblaze: Define microblaze barrier
microblaze: Remove empty headers
microblaze: Remove early printk setup
microblaze: Remove architecture tlb.h and use generic one
microblaze: Convert headers to SPDX license
microblaze: Fix _reset() function
microblaze: Kernel parameters should be parsed earlier
