Implement common function for locking/unlocking 8 hardware
semaphores used for serializing access to shared resouces
on a NIC board by different PCI functions.
As by definition, callers of these semaphore API can be
put to sleep till the semaphore is locked.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove code for phy access on unreleased NX2031 based quad-gig board.
NX3031 based production quad-gig boards do not require direct phy
access by driver.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is based on commit d2f3ad4 (pxaficp-ir: remove incorrect
net_device_ops). Do the same for sa1100_ir.
Untested.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is based on commit d2f3ad4 (pxaficp-ir: remove incorrect
net_device_ops). Do the same for au1k_ir.
Untested.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NETPOLL requires that interrupts remain disabled in its callbacks.
Using *_irq_save()/irq_restore() to replace *_irq_disable()/irq_enable()
functions in NETPOLL's callbacks of smc91x, so that it doesn't enable
interrupts when already disabled, and kgdboe/netconsole would work
properly over smc91x.
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes broken pxaficp-ir. The problem was in incorrect
net_device_ops being specified which prevented the driver from
operating. The symptoms were:
- failing ifconfig for IrLAN, resulting in
SIOCSIFFLAGS: Cannot assign requested address
- irattach working for IrCOMM, but the port stayed disabled
Moreover this patch corrects missing sysfs device link.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NETPOLL API requires that interrupts remain disabled in
netpoll_send_skb(). The use of "A functions set" in the NETPOLL API
callbacks causes the interrupts to get enabled and can lead to kernel
instability.
The solution is to use "B functions set" to prevent the irqs from
getting enabled while in netpoll_send_skb().
A functions set:
local_irq_disable()/local_irq_enable()
spin_lock_irq()/spin_unlock_irq()
spin_trylock_irq()/spin_unlock_irq()
B functions set:
local_irq_save()/local_irq_restore()
spin_lock_irqsave()/spin_unlock_irqrestore()
spin_trylock_irqsave()/spin_unlock_irqrestore()
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of fully initializing an unusable second r6040
device, perform the PHY detection earlier and bail out
in r6040_init_one when we could not read the PHY identifier.
Signed-off-by: Mark Kelly <mark@bifferos.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
E100 places it's RX packet descriptors inside skb->data and uses them
with bidirectional streaming DMA mapping. Data in descriptors is
accessed simultaneously by the chip (writing status and size when
a packet is received) and CPU (reading to check if the packet was
received). This isn't a valid usage of PCI DMA API, which requires use
of the coherent (consistent) memory for such purpose. Unfortunately e100
chips working in "simplified" RX mode have to store received data
directly after the descriptor. Fixing the driver to conform to the API
would require using unsupported "flexible" RX mode or receiving data
into a coherent memory and using CPU to copy it to network buffers.
This patch, while not yet making the driver conform to the PCI DMA API,
allows it to work correctly on X86 with swiotlb (while not breaking
other architectures).
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate register definitions in netxen_nic_hdr.h
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement pci driver shutdown functionality, this helps
quiescing all PCI transaction before chipset is reset.
Amit Kumar Salecha <amit@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all tx skb mapping code into netxen_map_tx_skb().
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If netxen_need_fw_reset() return 0 [ implies firmware is up
and running], still go through dma mask check, etc.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool -K knob to control LRO in firmware.
LRO path is completely separated from GRO, LRO packets
are still fed with netif_receive_skb().
Also fix ethtool statistics to include LRO packets.
Also use correct message type while configuring interrupt coalescing.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Set the USE_INT_PARAM bit so the rx-frames-irq and tx-frames-irq will take
effect on 5709.
- Increase the default rx-frames to reduce interrupt count.
- Decrease the default rx-frames-irq and tx-frames-irq to catch more events
during NAPI poll.
All these will reduce interrupts without affecting latency.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report this counter to ethtool -S and include it in netstat.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unable to allocate memory for new MTU or new ring size, we need
to close the device to prevent it from crashing.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add this check to bnx2_netif_stop() and bnx2_vlan_rx_register() to
prevent bus lockups on some systems when the chip is in low power state.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case IRQs are shared, we will not mistakenly start processing
the ring based on old status block indices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8187B always needs MSR_LINK_ENEDCA flag to be set even when it is in
no link mode, otherwise it'll not be able to associate when this flag is
not set after the change "mac80211: fix managed mode BSSID handling".
By accident, setting BSSID of AP before association makes 8187B to
successfuly associate even when ENEDCA flag isn't set, which was the
case before the mac80211 change. But now the BSSID of AP we are trying
to associate is only available after association is successful, and
any attempt to associate without the needed flag doesn't work.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current mwl8k_priv->fw_lock spinlock doesn't actually protect
against multiple commands being submitted at once, as it is not kept
held over the entire firmware command submission. And since waiting
for command completion sleeps, we can't use a spinlock anyway.
To fix mwl8k firmware command serialisation properly, we have the
following requirements:
- Some commands require that the packet transmit path is idle when
the command is issued. (For simplicity, we'll just quiesce the
transmit path for every command.)
- There are certain sequences of commands that need to be issued to
the hardware sequentially, with no other intervening commands.
This leads to an implementation of a "firmware lock" as a mutex that
can be taken recursively, and which is taken by both the low-level
command submission function (mwl8k_post_cmd) as well as any users of
that function that require issuing of an atomic sequence of commands,
and quiesces the transmit path whenever it's taken.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delete most of the mwl8k_work_struct fields and options, since most
of them are unused or never changed from their defaults:
- We always use priv->config_wq, so delete the wqueue argument from
mwl8k_queue_work().
- MWL8K_WQ_SPIN and MWL8K_WQ_POST_REQUEST are never used, as all
callers sleep for request completion, so sleep unconditionally.
- MWL8K_WQ_FREE_WORKSTRUCT is never used.
- MWL8K_WQ_TX_WAIT_EMPTY is always set, so assume it unconditionally.
- timeout_ms/txwait_attempts/tx_timeout_ms are never changed from
their defaults, so just hardcode these in the workqueue worker.
- step is never used.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various mwl8k_txq_xmit changes:
- Extract the QoS field before adding the DMA header.
- Only write to tx->status once, and only after all the other
descriptor fields have been set.
- Do all tx state manipulation under the tx spinlock.
- Remove the priv->inconfig check, as all transmit queues will
be frozen during config cycles, so we won't ever be asked to
transmit if a config cycle is running.
- Remove some more dead code.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use MWL8K_TX_QUEUES instead of a hardcoded "4" in a couple of places.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since firmware load commands don't generate 'command done' interrupts
like normal commands do, polling for command done interrupts just
unnecessarily slows down the firmware load process. Removing this bit
of code speeds up loading a typical firmware image from 840 msec to
180 msec.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding and removing the DMA header that the mwl8k hardware requires
on tx and provides on rx can never fail, since we are guaranteed to
have enough headroom on the tx path to expand the packet, and we only
ever shrink the packet on the rx path. (And on both paths we are
guaranteed to be the only user of the skb we are handling.)
This allows removing all of the skb clone handling in the tx and tx
reclaim paths, and eliminates error checks in both the tx and rx
paths, simplifying the code a bit more.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to check for NL80211_IFTYPE_MONITOR in
->add_interface(), as this function is never called for monitor
interfaces. Also, there is no need to advertise this bit in our
wiphy's ->interface_modes.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k_configure_filter() passes pointers to total_flags and the
multicast address list to a workqueue function, while there is no
guarantee that those pointers will still be valid by the time the
workqueue function runs.
Solve this by passing total_flags by value, and by passing an
already built multicast address setup command packet to the workqueue
function so that we don't have to look at the multicast address list
itself outside of mwl8k_configure_filter().
Also, since ->configure_filter() can sleep now, wait synchronously
for the worker to finish.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
