Since the driver was first introduced into the kernel, it has only
handled the ciphers associated with WEP, WPA, and WPA2. It fails with
WPA3 even though mac80211 can handle those additional ciphers in software,
b43legacy did not report that it could handle them. By setting MFP_CAPABLE using
ieee80211_set_hw(), the problem is fixed.
With this change, b43legacy will handle the ciphers it knows in hardware,
and let mac80211 handle the others in software. It is not necessary to
use the module parameter NOHWCRYPT to turn hardware encryption off.
Although this change essentially eliminates that module parameter,
I am choosing to keep it for cases where the hardware is broken,
and software encryption is required for all ciphers.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200526155909.5807-3-Larry.Finger@lwfinger.net
Since the driver was first introduced into the kernel, it has only
handled the ciphers associated with WEP, WPA, and WPA2. It fails with
WPA3 even though mac80211 can handle those additional ciphers in software,
b43 did not report that it could handle them. By setting MFP_CAPABLE using
ieee80211_set_hw(), the problem is fixed.
With this change, b43 will handle the ciphers it knows in hardware,
and let mac80211 handle the others in software. It is not necessary to
use the module parameter NOHWCRYPT to turn hardware encryption off.
Although this change essentially eliminates that module parameter,
I am choosing to keep it for cases where the hardware is broken,
and software encryption is required for all ciphers.
Reported-and-tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200526155909.5807-2-Larry.Finger@lwfinger.net
This reverts commit 07d0f55349.
For rtw88 driver, the SDIO is going to be supported, so there is
no need to remove the SDIO related power sequence settings. And
while the power sequence parser will pass in the mask of the HCI,
the SDIO part will not be used to set registers accordingly.
Moreover, the power sequence table is released as a whole package,
so the next time if we are going to update, the SDIO settings will
be overwritten. So, revert this now.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200520055350.23328-1-yhchuang@realtek.com
A test with the command below gives this error:
arch/arm/boot/dts/rk3188-bqedison2qc.dt.yaml:
touchscreen@3e: reg:0:0: 56 was expected
The touchscreen chip on 'rk3188-bqedison2qc' and other BQ models
was shipped with different addresses then the binding currently allows.
Change the reg property that any address will pass.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/input/touchscreen/
edt-ft5x06.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Baikal-T1 SoC provides a DW DMA controller to perform low-speed peripherals
Mem-to-Dev and Dev-to-Mem transaction. This is also applicable to the DW
APB SSI devices embedded into the SoC. Currently the DMA-based transfers
are supported by the DW APB SPI driver only as a middle layer code for
Intel MID/Elkhart PCI devices. Seeing the same code can be used for normal
platform DMAC device we introduced a set of patches to fix it within this
series.
First of all we need to add the Tx and Rx DMA channels support into the DW
APB SSI binding. Then there are several fixes and cleanups provided as a
initial preparation for the Generic DMA support integration: add Tx/Rx
finish wait methods, clear DMAC register when done or stopped, Fix native
CS being unset, enable interrupts in accordance with DMA xfer mode,
discard static DW DMA slave structures, discard unused void priv pointer
and dma_width member of the dw_spi structure, provide the DMA Tx/Rx burst
length parametrisation and make sure it's optionally set in accordance
with the DMA max-burst capability.
In order to have the DW APB SSI MMIO driver working with DMA we need to
initialize the paddr field with the physical base address of the DW APB SSI
registers space. Then we unpin the Intel MID specific code from the
generic DMA one and placed it into the spi-dw-pci.c driver, which is a
better place for it anyway. After that the naming cleanups are performed
since the code is going to be used for a generic DMAC device. Finally the
Generic DMA initialization can be added to the generic version of the
DW APB SSI IP.
Last but not least we traditionally convert the legacy plain text-based
dt-binding file with yaml-based one and as a cherry on a cake replace
the manually written DebugFS registers read method with a ready-to-use
for the same purpose regset32 DebugFS interface usage.
This patchset is rebased and tested on the spi/for-next (5.7-rc5):
base-commit: fe9fce6b2cf3 ("Merge remote-tracking branch 'spi/for-5.8' into spi-next")
Link: https://lore.kernel.org/linux-spi/20200508132943.9826-1-Sergey.Semin@baikalelectronics.ru/
Changelog v2:
- Rebase on top of the spi repository for-next branch.
- Move bindings conversion patch to the tail of the series.
- Move fixes to the head of the series.
- Apply as many changes as possible to be applied the Generic DMA
functionality support is added and the spi-dw-mid is moved to the
spi-dw-dma driver.
- Discard patch "spi: dw: Fix dma_slave_config used partly uninitialized"
since the problem has already been fixed.
- Add new patch "spi: dw: Discard unused void priv pointer".
- Add new patch "spi: dw: Discard dma_width member of the dw_spi structure".
n_bytes member of the DW SPI data can be used instead.
- Build the DMA functionality into the DW APB SSI core if required instead
of creating a separate kernel module.
- Use conditional statement instead of the ternary operator in the ref
clock getter.
Link: https://lore.kernel.org/linux-spi/20200515104758.6934-1-Sergey.Semin@baikalelectronics.ru/
Changelog v3:
- Use spi_delay_exec() method to wait for the DMA operation completion.
- Explicitly initialize the dw_dma_slave members on stack.
- Discard the dws->fifo_len utilization in the Tx FIFO DMA threshold
setting from the patch where we just add the default burst length
constants.
- Use min() method to calculate the optimal burst values.
- Add new patch which moves the spi-dw.c source file to spi-dw-core.c in
order to preserve the DW APB SSI core driver name.
- Add commas in the debugfs_reg32 structure initializer and after the last
entry of the dw_spi_dbgfs_regs array.
Link: https://lore.kernel.org/linux-spi/20200521012206.14472-1-Sergey.Semin@baikalelectronics.ru
Changelog v4:
- Get back ndelay() method to wait for an SPI transfer completion.
spi_delay_exec() isn't suitable for the atomic context.
Link: https://lore.kernel.org/linux-spi/20200522000806.7381-1-Sergey.Semin@baikalelectronics.ru
Changelog v5:
- Refactor the Tx/Rx DMA-based SPI transfers wait methods.
- Add a new patch "spi: dw: Set xfer effective_speed_hz".
- Add a new patch "spi: dw: Return any value retrieved from the
dma_transfer callback" as a preparation patch before implementing
the local DMA, Tx SPI and Rx SPI transfers wait methods.
- Add a new patch "spi: dw: Locally wait for the DMA transactions
completion", which provides a local DMA transaction complete
method
- Create a dedicated patch which adds the Rx-done wait method:
"spi: dw: Add SPI Rx-done wait method to DMA-based transfer".
- Add more detailed description of the problems the Tx/Rx-wait
methods-related patches fix.
- Wait for the SPI Tx and Rx transfers being finished in the
mid_spi_dma_transfer() method executed in the task context.
- Use spi_delay_exec() to wait for the SPI Tx/Rx completion, since now
the driver calls the wait methods in the kernel thread context.
- Use SPI_DELAY_UNIT_SCK spi_delay unit for Tx-wait delay, since SPI
xfer's are now have the effective_speed_hz initialized.
- Rx-wait for a delay correlated with the APB/SSI synchronous clock
rate instead of using the SPI bus clock rate.
Link: https://lore.kernel.org/linux-spi/20200529035915.20790-1-Sergey.Semin@baikalelectronics.ru
Changelog v6:
- Provide a more detailed description of the patch:
2901db35bea1 ("spi: dw: Locally wait for the DMA transfers completion")
- Calculate the Rx delay with better accuracy by moving 4-multiplication
to the head of the formulae:
ns = 4U * NSEC_PER_SEC / dws->max_freq * nents.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Maxim Kaurkin <Maxim.Kaurkin@baikalelectronics.ru>
Cc: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Cc: Ekaterina Skachko <Ekaterina.Skachko@baikalelectronics.ru>
Cc: Vadim Vlasov <V.Vlasov@baikalelectronics.ru>
Cc: Alexey Kolotnikov <Alexey.Kolotnikov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-spi@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Serge Semin (16):
spi: dw: Set xfer effective_speed_hz
spi: dw: Return any value retrieved from the dma_transfer callback
spi: dw: Locally wait for the DMA transfers completion
spi: dw: Add SPI Tx-done wait method to DMA-based transfer
spi: dw: Add SPI Rx-done wait method to DMA-based transfer
spi: dw: Parameterize the DMA Rx/Tx burst length
spi: dw: Use DMA max burst to set the request thresholds
spi: dw: Fix Rx-only DMA transfers
spi: dw: Add core suffix to the DW APB SSI core source file
spi: dw: Move Non-DMA code to the DW PCIe-SPI driver
spi: dw: Remove DW DMA code dependency from DW_DMAC_PCI
spi: dw: Add DW SPI DMA/PCI/MMIO dependency on the DW SPI core
spi: dw: Cleanup generic DW DMA code namings
spi: dw: Add DMA support to the DW SPI MMIO driver
spi: dw: Use regset32 DebugFS method to create regdump file
dt-bindings: spi: Convert DW SPI binding to DT schema
.../bindings/spi/snps,dw-apb-ssi.txt | 44 --
.../bindings/spi/snps,dw-apb-ssi.yaml | 127 +++++
.../devicetree/bindings/spi/spi-dw.txt | 24 -
drivers/spi/Kconfig | 15 +-
drivers/spi/Makefile | 5 +-
drivers/spi/{spi-dw.c => spi-dw-core.c} | 95 ++--
drivers/spi/spi-dw-dma.c | 482 ++++++++++++++++++
drivers/spi/spi-dw-mid.c | 382 --------------
drivers/spi/spi-dw-mmio.c | 4 +
drivers/spi/spi-dw-pci.c | 50 +-
drivers/spi/spi-dw.h | 20 +-
11 files changed, 719 insertions(+), 529 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt
create mode 100644 Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml
delete mode 100644 Documentation/devicetree/bindings/spi/spi-dw.txt
rename drivers/spi/{spi-dw.c => spi-dw-core.c} (82%)
create mode 100644 drivers/spi/spi-dw-dma.c
delete mode 100644 drivers/spi/spi-dw-mid.c
--
2.26.2
bcm2711, Rasberry Pi 4's SoC, shares one interrupt for multiple
instances of the bcm2835 SPI controller. So this enables shared
interrupt support for them.
The early bail out in the interrupt routine avoids messing with buffers
of transfers being done by other means. Otherwise, the driver can handle
receiving interrupts asserted by other controllers during an IRQ based
transfer.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200528185805.28991-1-nsaenzjulienne@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Most of blk-mq drivers depend on managed IRQ's auto-affinity to setup
up queue mapping. Thomas mentioned the following point[1]:
"That was the constraint of managed interrupts from the very beginning:
The driver/subsystem has to quiesce the interrupt line and the associated
queue _before_ it gets shutdown in CPU unplug and not fiddle with it
until it's restarted by the core when the CPU is plugged in again."
However, current blk-mq implementation doesn't quiesce hw queue before
the last CPU in the hctx is shutdown. Even worse, CPUHP_BLK_MQ_DEAD is a
cpuhp state handled after the CPU is down, so there isn't any chance to
quiesce the hctx before shutting down the CPU.
Add new CPUHP_AP_BLK_MQ_ONLINE state to stop allocating from blk-mq hctxs
where the last CPU goes away, and wait for completion of in-flight
requests. This guarantees that there is no inflight I/O before shutting
down the managed IRQ.
Add a BLK_MQ_F_STACKING and set it for dm-rq and loop, so we don't need
to wait for completion of in-flight requests from these drivers to avoid
a potential dead-lock. It is safe to do this for stacking drivers as those
do not use interrupts at all and their I/O completions are triggered by
underlying devices I/O completion.
[1] https://lore.kernel.org/linux-block/alpine.DEB.2.21.1904051331270.1802@nanos.tec.linutronix.de/
[hch: different retry mechanism, merged two patches, minor cleanups]
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a new blk_mq_all_tag_iter function to iterate over all allocated
scheduler tags and driver tags. This is more flexible than the existing
blk_mq_all_tag_busy_iter function as it allows the callers to do whatever
they want on allocated request instead of being limited to started
requests.
It will be used to implement draining allocated requests on specified
hctx in this patchset.
[hch: switch from the two booleans to a more readable flags field and
consolidate the tags iter functions]
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Bart van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_mq_alloc_request_hctx is only used for NVMeoF connect commands, so
tailor it to the specific requirements, and don't bother the general
fast path code with its special twinkles.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Don't split request initialization between __blk_mq_alloc_request and
blk_mq_rq_ctx_init. Also remove the op argument as it can be derived
from the blk_mq_alloc_data structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The bio argument is entirely unused, and the request_queue can be passed
through the alloc_data, given that it needs to be filled out for the
low-level tag allocation anyway. Also rename the function to
__blk_mq_alloc_request as the switch between get and alloc in the call
chains is rather confusing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Drivers may need to bypass error injection for error recovery. Rename
__blk_mq_complete_request() to blk_mq_force_complete_rq() and export
that function so drivers may skip potential fake timeouts after they've
reclaimed lost requests.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
kobject_init_and_add() takes reference even when it fails.
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object.
Previous commit "b8eb718348b8" fixed a similar problem.
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Versions of VMD with the Host Physical Address shadow register use this
register to calculate the bus address offset needed to do guest
passthrough of the domain. This register shadows the Host Physical
Address registers including the resource type bits. After calculating
the offset, the extra resource type bits lead to the VMD resources being
over-provisioned at the front and under-provisioned at the back.
Example:
pci 10000:80:02.0: reg 0x10: [mem 0xf801fffc-0xf803fffb 64bit]
Expected:
pci 10000:80:02.0: reg 0x10: [mem 0xf8020000-0xf803ffff 64bit]
If other devices are mapped in the over-provisioned front, it could lead
to resource conflict issues with VMD or those devices.
Link: https://lore.kernel.org/r/20200528030240.16024-3-jonathan.derrick@intel.com
Fixes: a1a3017013 ("PCI: vmd: Fix shadow offsets to reflect spec changes")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The name of pm_runtime_callbacks_present() is confusing, because
it suggests that the device has PM-runtime callbacks if 'true' is
returned by that function, but in fact that may not be the case,
so replace it with pm_runtime_has_no_callbacks() which is not
ambiguous.
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
FE state is SND_SOC_DPCM_STATE_PREPARE now, BE1 is
used by FE.
Later when new BE2 is added to FE by mixer update,
it will call dpcm_run_update_startup() to update
BE2's state, but unfortunately BE2 .prepare() meets
error, it will disconnect all non started BE.
This make BE1 dai skip .hw_free() and .shutdown(),
and the BE1 users will never decrease to zero.
Signed-off-by: zhucancan <zhucancan@vivo.com>
Link: https://lore.kernel.org/r/ALMAWwB5CP9aAcKXCU5FzqqF.1.1590747164172.Hmail.zhucancan@vivo.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add documentation for the interconnects and interconnect-names
properties for USB.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Use 'struct domain_pgtable' instead to free_pagetable(). This solves
the problem that amd_iommu_domain_direct_map() needs to restore
domain->pt_root after the device table has been updated just to make
free_pagetable release the domain page-table.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20200527115313.7426-4-joro@8bytes.org
This function is internal to the AMD IOMMU driver and only exported
because the amd_iommu_v2 modules calls it. But the reason it is called
from there could better be handled by amd_iommu_is_attach_deferred().
So unexport get_dev_data() and use amd_iommu_is_attach_deferred()
instead.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20200527115313.7426-3-joro@8bytes.org
get_user_pages_fast() doesn't need the caller to check that.
NB: reachable only from ioctl(2) and only under USER_DS
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
pin_user_pages_fast() doesn't need that from its caller.
NB: only reachable from ->ioctl(), and only under USER_DS
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
in all affected cases addresses are passed only to
copy_from()_user or copy_to_user().
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
No, you do NOT need to "protect copy from user" that way.
Incidentally, your userland ABI stinks. I understand that you
wanted to accept "reset" and "reset\n" as equivalent, but I suspect
that accepting "reset this, you !@^!@!" had been an accident.
Nothing to do about that now - it is a userland ABI...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
