USB2 devices with LPM enabled may interrupt the system suspend:
[ 932.510475] usb 1-7: usb suspend, wakeup 0
[ 932.510549] hub 1-0:1.0: hub_suspend
[ 932.510581] usb usb1: bus suspend, wakeup 0
[ 932.510590] xhci_hcd 0000:00:14.0: port 9 not suspended
[ 932.510593] xhci_hcd 0000:00:14.0: port 8 not suspended
..
[ 932.520323] xhci_hcd 0000:00:14.0: Port change event, 1-7, id 7, portsc: 0x400e03
..
[ 932.591405] PM: pci_pm_suspend(): hcd_pci_suspend+0x0/0x30 returns -16
[ 932.591414] PM: dpm_run_callback(): pci_pm_suspend+0x0/0x160 returns -16
[ 932.591418] PM: Device 0000:00:14.0 failed to suspend async: error -16
During system suspend, USB core will let HC suspends the device if it
doesn't have remote wakeup enabled and doesn't have any children.
However, from the log above we can see that the usb 1-7 doesn't get bus
suspended due to not in U0. After a while the port finished U2 -> U0
transition, interrupts the suspend process.
The observation is that after disabling LPM, port doesn't transit to U0
immediately and can linger in U2. xHCI spec 4.23.5.2 states that the
maximum exit latency for USB2 LPM should be BESL + 10us. The BESL for
the affected device is advertised as 400us, which is still not enough
based on my testing result.
So let's use the maximum permitted latency, 10000, to poll for U0
status to solve the issue.
Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200624135949.22611-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unable to complete the enumeration of a USB TV Tuner device.
Per XHCI spec (4.6.5), the EP state field of the input context shall
be cleared for a set address command. In the special case of an FS
device that has "MaxPacketSize0 = 8", the Linux XHCI driver does
not do this before evaluating the context. With an XHCI controller
that checks the EP state field for parameter context error this
causes a problem in cases such as the device getting reset again
after enumeration.
When that field is cleared, the problem does not occur.
This was found and fixed by Sasi Kumar.
Cc: stable@vger.kernel.org
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200624135949.22611-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A Synopsys USB2.0 core used in Huawei Kunpeng920 SoC has a bug which
might cause the host controller not issuing ping.
Bug description:
After indicating an Interrupt on Async Advance, the software uses the
doorbell mechanism to delete the Next Link queue head of the last
executed queue head. At this time, the host controller still references
the removed queue head(the queue head is NULL). NULL reference causes
the host controller to lose the USB device.
Solution:
After deleting the Next Link queue head, when has_synopsys_hc_bug set
to 1，the software can write one of the valid queue head addresses to
the ASYNCLISTADDR register to allow the host controller to get
the valid queue head. in order to solve that problem, this patch set
the flag for Huawei Kunpeng920
There are detailed instructions and solutions in this patch:
commit 2f7ac6c199 ("USB: ehci: add workaround for Synopsys HC bug")
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1591588019-44284-1-git-send-email-liulongfang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Pull USB/PHY driver updates from Greg KH:
"Here are the large set of USB and PHY driver updates for 5.8-rc1.
Nothing huge, just lots of little things:
- USB gadget fixes and additions all over the place
- new PHY drivers
- PHY driver fixes and updates
- XHCI driver updates
- musb driver updates
- more USB-serial driver ids added
- various USB quirks added
- thunderbolt minor updates and fixes
- typec updates and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (245 commits)
usb: dwc3: meson-g12a: fix USB2 PHY initialization on G12A and A1 SoCs
usb: dwc3: meson-g12a: fix error path when fetching the reset line fails
Revert "dt-bindings: usb: qcom,dwc3: Convert USB DWC3 bindings"
Revert "dt-bindings: usb: qcom,dwc3: Add compatible for SC7180"
Revert "dt-bindings: usb: qcom,dwc3: Introduce interconnect properties for Qualcomm DWC3 driver"
USB: serial: ch341: fix lockup of devices with limited prescaler
USB: serial: ch341: add basis for quirk detection
CDC-ACM: heed quirk also in error handling
USB: serial: option: add Telit LE910C1-EUX compositions
usb: musb: Fix runtime PM imbalance on error
usb: musb: jz4740: Prevent lockup when CONFIG_SMP is set
usb: musb: mediatek: add reset FADDR to zero in reset interrupt handle
usb: musb: use true for 'use_dma'
usb: musb: start session in resume for host port
usb: musb: return -ESHUTDOWN in urb when three-strikes error happened
USB: serial: qcserial: add DW5816e QDL support
thunderbolt: Add trivial .shutdown
usb: dwc3: keystone: Turn on USB3 PHY before controller
dt-bindings: usb: ti,keystone-dwc3.yaml: Add USB3.0 PHY property
dt-bindings: usb: convert keystone-usb.txt to YAML
...
The comparison of hcd->irq to less than zero for an error check will
never be true because hcd->irq is an unsigned int. Fix this by
assigning the int retval to the return of platform_get_irq and checking
this for the -ve error condition and assigning hcd->irq to retval.
Addresses-Coverity: ("Unsigned compared against 0")
Fixes: c856b4b0fd ("USB: EHCI: ehci-mv: fix error handling in mv_ehci_probe()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200515165453.104028-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When renesas module is not built, we get compiler warning on xhci driver
with W=1
CC [M] drivers/usb/host/xhci-rcar.o
drivers/usb/host/xhci-pci.h:13:5: warning: no previous prototype for ‘renesas_xhci_check_request_fw’ [-Wmissing-prototypes]
int renesas_xhci_check_request_fw(struct pci_dev *dev,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/usb/host/xhci-pci.h:19:6: warning: no previous prototype for ‘renesas_xhci_pci_exit’ [-Wmissing-prototypes]
void renesas_xhci_pci_exit(struct pci_dev *dev) { };
^~~~~~~~~~~~~~~~~~~~~
We have defined these symbols when CONFIG_USB_XHCI_PCI_RENESAS is not
defined, but missed making then static.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 8bd5741e31 ("usb: renesas-xhci: Add the renesas xhci driver")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200519093002.1152144-1-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci-pci-renesas module exports symbols for xhci-pci to load the
RAM/ROM on renesas xhci controllers. We had dependency which works
when both the modules are builtin or modules.
But if xhci-pci is inbuilt and xhci-pci-renesas in module, we get below
linker error:
drivers/usb/host/xhci-pci.o: In function `xhci_pci_remove':
drivers/usb/host/xhci-pci.c:411: undefined reference to `renesas_xhci_pci_exit'
drivers/usb/host/xhci-pci.o: In function `xhci_pci_probe':
drivers/usb/host/xhci-pci.c:345: undefined reference to `renesas_xhci_check_request_fw'
Fix this by adding USB_XHCI_PCI having depends on USB_XHCI_PCI_RENESAS
|| !USB_XHCI_PCI_RENESAS so that both can be either inbuilt or modules.
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Fixes: a66d21d7db ("usb: xhci: Add support for Renesas controller with memory")
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200519050622.994908-1-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_unaligned_le16() is defined in linux/unaligned/access_ok.h header
but it uses symbols which may not be available, leading to build
failures on ia64. Using asm/unaligned.h seem to be the right thing
and used in other drivers.
This fixes below error reported by kbuild test robot
In file included from drivers/usb/host/xhci-pci-renesas.c:9:
>> include/linux/unaligned/access_ok.h:8:28: error: redefinition of 'get_unaligned_le16'
8 | static __always_inline u16 get_unaligned_le16(const void *p)
| ^~~~~~~~~~~~~~~~~~
In file included from arch/ia64/include/asm/unaligned.h:5,
from arch/ia64/include/asm/io.h:23,
from arch/ia64/include/asm/smp.h:21,
from include/linux/smp.h:67,
from include/linux/percpu.h:7,
from include/linux/arch_topology.h:9,
from include/linux/topology.h:30,
from include/linux/gfp.h:9,
from include/linux/xarray.h:14,
from include/linux/radix-tree.h:18,
from include/linux/idr.h:15,
from include/linux/kernfs.h:13,
from include/linux/sysfs.h:16,
from include/linux/kobject.h:20,
from include/linux/of.h:17,
from include/linux/irqdomain.h:35,
from include/linux/acpi.h:13,
from drivers/usb/host/xhci-pci-renesas.c:4:
include/linux/unaligned/le_struct.h:7:19: note: previous definition of 'get_unaligned_le16' was here
7 | static inline u16 get_unaligned_le16(const void *p)
| ^~~~~~~~~~~~~~~~~~
In file included from drivers/usb/host/xhci-pci-renesas.c:9:
include/linux/unaligned/access_ok.h:13:28: error: redefinition of 'get_unaligned_le32'
13 | static __always_inline u32 get_unaligned_le32(const void *p)
| ^~~~~~~~~~~~~~~~~~
In file included from arch/ia64/include/asm/unaligned.h:5,
from arch/ia64/include/asm/io.h:23,
from arch/ia64/include/asm/smp.h:21,
from include/linux/smp.h:67,
from include/linux/percpu.h:7,
from include/linux/arch_topology.h:9,
from include/linux/topology.h:30,
from include/linux/gfp.h:9,
from include/linux/xarray.h:14,
from include/linux/radix-tree.h:18,
from include/linux/idr.h:15,
from include/linux/kernfs.h:13,
from include/linux/sysfs.h:16,
from include/linux/kobject.h:20,
from include/linux/of.h:17,
from include/linux/irqdomain.h:35,
from include/linux/acpi.h:13,
from drivers/usb/host/xhci-pci-renesas.c:4:
include/linux/unaligned/le_struct.h:12:19: note: previous definition of 'get_unaligned_le32' was here
Fixes: 8bd5741e31 ("usb: renesas-xhci: Add the renesas xhci driver")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200516162516.385149-1-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This add a new driver for renesas xhci which is basically a firmware
loader for uPD720201 and uPD720202 w/o ROM. The xhci-pci driver will
invoke this driver for loading/unloading on relevant devices.
This patch adds a firmware loader for the uPD720201K8-711-BAC-A
and uPD720202K8-711-BAA-A variant. Both of these chips are listed
in Renesas' R19UH0078EJ0500 Rev.5.00 "User's Manual: Hardware" as
devices which need the firmware loader on page 2 in order to
work as they "do not support the External ROM".
The "Firmware Download Sequence" is describe in chapter
"7.1 FW Download Interface" R19UH0078EJ0500 Rev.5.00 page 131.
The firmware "K2013080.mem" is available from a USB3.0 Host to
PCIe Adapter (PP2U-E card) "Firmware download" archive. An
alternative version can be sourced from Netgear's WNDR4700 GPL
archives.
The release notes of the PP2U-E's "Firmware Download" ver 2.0.1.3
(2012-06-15) state that the firmware is for the following devices:
- uPD720201 ES 2.0 sample whose revision ID is 2.
- uPD720201 ES 2.1 sample & CS sample & Mass product, ID is 3.
- uPD720202 ES 2.0 sample & CS sample & Mass product, ID is 2.
[vkoul: fixed comments:
used macros for timeout count and delay
removed renesas_fw_alive_check
cleaned renesas_fw_callback
removed recursion for renesas_fw_download
add register defines and field names
move to a separate file
make fw loader as sync probe so that we execute in probe and
prevent race
make xhci-pci-renesas a seprate module]
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200514122039.300417-3-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_hcd_pci_probe expects users to call this with driver_data set as
hc_driver, that limits the possibility of using the driver_data for
driver data.
Add hc_driver as argument to usb_hcd_pci_probe and modify the callers
ehci/ohci/xhci/uhci to pass hc_driver as argument and freeup the
driver_data used
Tested xhci driver on Dragon-board RB3, compile tested ehci, ohci and
uhci.
[For all but the xHCI parts]
[For the xhci part]
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200514122039.300417-2-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On platforms with IOMMU enabled, multiple SGs can be coalesced into one
by the IOMMU driver. In that case the SG list processing as part of the
completion of a urb on a bulk endpoint can result into a NULL pointer
dereference with the below stack dump.
<6> Unable to handle kernel NULL pointer dereference at virtual address 0000000c
<6> pgd = c0004000
<6> [0000000c] *pgd=00000000
<6> Internal error: Oops: 5 [#1] PREEMPT SMP ARM
<2> PC is at xhci_queue_bulk_tx+0x454/0x80c
<2> LR is at xhci_queue_bulk_tx+0x44c/0x80c
<2> pc : [<c08907c4>] lr : [<c08907bc>] psr: 000000d3
<2> sp : ca337c80 ip : 00000000 fp : ffffffff
<2> r10: 00000000 r9 : 50037000 r8 : 00004000
<2> r7 : 00000000 r6 : 00004000 r5 : 00000000 r4 : 00000000
<2> r3 : 00000000 r2 : 00000082 r1 : c2c1a200 r0 : 00000000
<2> Flags: nzcv IRQs off FIQs off Mode SVC_32 ISA ARM Segment none
<2> Control: 10c0383d Table: b412c06a DAC: 00000051
<6> Process usb-storage (pid: 5961, stack limit = 0xca336210)
<snip>
<2> [<c08907c4>] (xhci_queue_bulk_tx)
<2> [<c0881b3c>] (xhci_urb_enqueue)
<2> [<c0831068>] (usb_hcd_submit_urb)
<2> [<c08350b4>] (usb_sg_wait)
<2> [<c089f384>] (usb_stor_bulk_transfer_sglist)
<2> [<c089f2c0>] (usb_stor_bulk_srb)
<2> [<c089fe38>] (usb_stor_Bulk_transport)
<2> [<c089f468>] (usb_stor_invoke_transport)
<2> [<c08a11b4>] (usb_stor_control_thread)
<2> [<c014a534>] (kthread)
The above NULL pointer dereference is the result of block_len and the
sent_len set to zero after the first SG of the list when IOMMU driver
is enabled. Because of this the loop of processing the SGs has run
more than num_sgs which resulted in a sg_next on the last SG of the
list which has SG_END set.
Fix this by check for the sg before any attributes of the sg are
accessed.
[modified reason for null pointer dereference in commit message subject -Mathias]
Fixes: f9c589e142 ("xhci: TD-fragment, align the unsplittable case with a bounce buffer")
Cc: stable@vger.kernel.org
Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200514110432.25564-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new EHCI driver for Broadcom STB SoC's. A new EHCI driver
was created instead of adding support to the existing ehci platform
driver because of the code required to work around bugs in the EHCI
controller. The primary workaround is for a bug where the Core
violates the SOF interval between the first two SOFs transmitted after
resume. This only happens if the resume occurs near the end of a
microframe. The fix is to intercept the ehci-hcd request to complete
RESUME and align it to the start of the next microframe.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200512150019.25903-5-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the Raspberry Pi 4, after a PCI reset, VL805's firmware may either be
loaded directly from an EEPROM or, if not present, by the SoC's
VideoCore. Inform VideoCore that VL805 was just reset.
Also, as this creates a dependency between USB_PCI and VideoCore's
firmware interface, and since USB_PCI can't be set as a module neither
this can. Reflect that on the firmware interface Kconfg.
Link: https://lore.kernel.org/r/20200505161318.26200-5-nsaenzjulienne@suse.de
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Fix the following coccicheck warning:
drivers/usb/host/pci-quirks.c:532:1-27: WARNING: Assignment of 0/1 to
bool variable
drivers/usb/host/pci-quirks.c:208:1-20: WARNING: Assignment of 0/1 to
bool variable
drivers/usb/host/pci-quirks.c:232:2-21: WARNING: Assignment of 0/1 to
bool variable
drivers/usb/host/pci-quirks.c:235:2-21: WARNING: Assignment of 0/1 to
bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200420042622.18564-1-yanaijie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default control endpoint ep0 can return a STALL indicating the
device does not support the control transfer requests. This is called
a protocol stall and does not halt the endpoint.
xHC behaves a bit different. Its internal endpoint state will always
be halted on any stall, even if the device side of the endpiont is not
halted. So we do need to issue the reset endpoint command to clear the
xHC host intenal endpoint halt state, but should not request the HS hub
to clear the TT buffer unless device side of endpoint is halted.
Clearing the hub TT buffer at protocol stall caused ep0 to become
unresponsive for some FS/LS devices behind HS hubs, and class drivers
failed to set the interface due to timeout:
usb 1-2.1: 1:1: usb_set_interface failed (-110)
Fixes: ef513be0a9 ("usb: xhci: Add Clear_TT_Buffer")
Cc: <stable@vger.kernel.org> # v5.3
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200421140822.28233-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a class driver cancels its only URB then the endpoint ring buffer will
appear empty to the xhci driver. xHC hardware may still process cached
TRBs, and complete with a STALL, halting the endpoint.
This halted endpoint was not handled correctly by xhci driver as events on
empty rings were all assumed to be spurious events.
xhci driver refused to restart the ring with EP_HALTED flag set, so class
driver was never informed the endpoint halted even if it queued new URBs.
The host side of the endpoint needs to be reset, and dequeue pointer should
be moved in order to clear the cached TRBs and resetart the endpoint.
Small adjustments in finding the new dequeue pointer are needed to support
the case of stall on an empty ring and unknown current TD.
Cc: <stable@vger.kernel.org>
cc: Jeremy Compostella <jeremy.compostella@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200421140822.28233-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
u132_static_list is a global list protected by u132_module_lock.
It is read in the u132_hcd_exit() function without holding the lock
thus may lead to data race.
However, it turns out that this list isn't used for anything useful
and thus it is okay to get rid of it.
Thus, remove the u132_static_list from u132-hcd module.
Also remove struct list_head u132_list from struct u132.
Found by Linux Driver Verification project (linuxtesting.org).
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Link: https://lore.kernel.org/r/20200404174102.19862-1-madhuparnabhowmik10@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get usb-phy's for availbale USB 2 phys. Register id notifiers for available
usb-phy's to receive role change notifications. Perform PP for the received
role change usb ports.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
[treding@nvidia.com: rebase onto Greg's usb-next branch]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Depending on the current link state the steps to resume the link to U0
varies. The normal case when a port is suspended (U3) we set the link
to U0 and wait for a port event when U3exit completed and port moved to
U0.
If the port is in U1/U2, then no event is issued, just set link to U0
If port is in Resume or Recovery state then the device has already
initiated resume, and this host initiated resume is racing against it.
Port event handler for device initiated resume will set link to U0,
just wait for the port to reach U0 before returning.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like U3 case, xHCI spec doesn't specify the upper bound of U0 transition
time. The 20ms is not enough for some devices.
Intead of polling PLS or PLC, we can facilitate the port change event to
know that the link transits to U0 is completed.
While at it, also separate U0 and U3 case to make the code cleaner.
[variable rename to u3exit, and skip completion for usb2 ports -Mathias ]
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI spec doesn't specify the upper bound of U3 transition time. For
some devices 20ms is not enough, so we need to make sure the link state
is in U3 before further actions.
I've tried to use U3 Entry Capability by setting U3 Entry Enable in
config register, however the port change event for U3 transition
interrupts the system suspend process.
For now let's use the less ideal method by polling PLS.
[use usleep_range(), and shorten the delay time while polling -Mathias]
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
