Pull RTC updates from Alexandre Belloni:
"A quiet cycle this time.
- ds1307: properly handle oscillator failure flags
- imx-sc: alarm support
- pcf2123: alarm support, correct offset handling
- sun6i: add R40 support
- simplify getting the adapter of an i2c client"
* tag 'rtc-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (37 commits)
rtc: wm831x: Add IRQF_ONESHOT flag
rtc: stm32: remove one condition check in stm32_rtc_set_alarm()
rtc: pcf2123: Fix build error
rtc: interface: Change type of 'count' from int to u64
rtc: pcf8563: Clear event flags and disable interrupts before requesting irq
rtc: pcf8563: Fix interrupt trigger method
rtc: pcf2123: fix negative offset rounding
rtc: pcf2123: add alarm support
rtc: pcf2123: use %ptR
rtc: pcf2123: port to regmap
rtc: pcf2123: remove sysfs register view
rtc: rx8025: simplify getting the adapter of a client
rtc: rx8010: simplify getting the adapter of a client
rtc: rv8803: simplify getting the adapter of a client
rtc: m41t80: simplify getting the adapter of a client
rtc: fm3130: simplify getting the adapter of a client
rtc: tegra: Drop MODULE_ALIAS
rtc: sun6i: Add R40 compatible
dt-bindings: rtc: sun6i: Add the R40 RTC compatible
dt-bindings: rtc: Convert Allwinner A31 RTC to a schema
...
Besides the alarm, the PCF8563 also has a timer triggered interrupt.
In cases where the previous system left the timer and interrupts on,
or somehow the bits got enabled, the interrupt would keep triggering
as the kernel doesn't know about it.
Clear both the alarm and timer event flags, and disable the interrupts,
before requesting the interrupt line.
Fixes: ede3e9d47c ("drivers/rtc/rtc-pcf8563.c: add alarm support")
Fixes: a45d528aab ("rtc: pcf8563: clear expired alarm at boot time")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The PCF8563 datasheet says the interrupt line is active low and stays
active until the events are cleared, i.e. a level trigger interrupt.
Fix the flags used to request the interrupt.
Fixes: ede3e9d47c ("drivers/rtc/rtc-pcf8563.c: add alarm support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow setting the alarm and later enable it instead of enabling it
unconditionally.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The pcf8563_clkout_recalc_rate function erroneously ignores the
frequency index read from the CLKO register and always returns
32768 Hz.
Fixes: a39a6405d5 ("rtc: pcf8563: add CLKOUT to common clock framework")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since all time members of the alarm data is initialized to -1 the drivers
are responsible to set the tm_sec member to 0.
Fixes: d68778b80d ("rtc: initialize output parameter for read alarm to "uninitialized"")
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since commit d68778b80d ("rtc: initialize output parameter for read
alarm to "uninitialized"") there is no need to explicitly set
unsupported members to -1. So drop the respective assignments from
drivers.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Many drivers are defining a DRV_VERSION. This is often only used for
MODULE_VERSION and sometimes to print an info message at probe time. This
is kind of pointless as they are all versionned with the kernel anyway.
Also the core will print a message when a new rtc is found.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add the clkout output clk to the common clock framework.
Disable the CLKOUT of the RTC after power-up.
After power-up/reset of the RTC, CLKOUT is enabled by default,
with CLKOUT enabled the RTC chip has 2-3 times higher power
consumption.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Gcc is unable to prove that alm_pending is always initialized
when it is used, so it prints a harmless warning:
drivers/rtc/rtc-pcf8563.c: In function 'pcf8563_probe':
drivers/rtc/rtc-pcf8563.c:449:5: warning: 'alm_pending' may be used uninitialized in this function [-Wmaybe-uninitialized]
This uses the same conditional expression that is used inside of
the pcf8563_get_alarm_mode() function, to help gcc figure it out
and shut up that warning, and make the ARM defconfigs build again
with no warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: a45d528aab ("rtc: pcf8563: clear expired alarm at boot time")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
pcf8563_rtc_set_alarm() uses deprecated rtc_tm_to_time()
and rtc_time_to_tm(), which will overflow in year 2106
on 32-bit machines.
This patch solves this by:
- Replacing rtc_time_to_tm() with rtc_time64_to_tm()
- Replacing rtc_tm_to_time() with rtc_tm_to_time64()
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Return -EINVAL if the voltage low bit is set to avoid getting a bogus
time at boot.
There was a comment stating that util-linux hwclock refuses to set a
new time if we return an error code on read, but at least the current
version do set the time as expected. Remove the comment and the check
for valid time, and let the rtc core check it for us.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This commit does not change any logic here. It just makes the code easier
to read.
This is how it looked like:
If err != 0 return err;
else return 0;
Signed-off-by: Robert Kmiec <robert.r.kmiec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As pointed out by Sergei Shtylyov, the pcf8563_irq function contains a
bug in the error handling: an interrupt handler is not supposed to
return an errno value but an 'enum irqreturn'.
Let's fix this by returning IRQ_NONE in case of a communication error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gcc-4.9 found a potential condition under which the 'pending' variable
may be used uninitialized:
drivers/rtc/rtc-pcf8563.c: In function 'pcf8563_irq':
drivers/rtc/rtc-pcf8563.c:173:5: warning: 'pending' may be used uninitialized in this function [-Wmaybe-uninitialized]
This is because in the pcf8563_get_alarm_mode() function, we check any
nonzero return of pcf8563_read_block_data, but in the irq function we
only check for negative values, so a possible positive value does not
get detected if the compiler chooses not to inline the entire call
chain.
Checking for any non-zero value in the interrupt handler as well is just
as correct and lets the compiler know what we are doing, without needing
a bogus initialization.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After the switch to devm_* functions and the removal of
rtc_device_unregister(), the 'remove' function does not do anything.
Delete it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The module.h was implicitly everywhere, but when we clean
that up, the implicit users will compile fail; fix them up
in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
