The pins on the Bay Trail SoC have separate input-buffer and output-buffer
enable bits and a read of the level bit of the value register will always
return the value from the input-buffer.
The BIOS of a device may configure a pin in output-only mode, only enabling
the output buffer, and write 1 to the level bit to drive the pin high.
This 1 written to the level bit will be stored inside the data-latch of the
output buffer.
But a subsequent read of the value register will return 0 for the level bit
because the input-buffer is disabled. This causes a read-modify-write as
done by byt_gpio_set_direction() to write 0 to the level bit, driving the
pin low!
Before this commit byt_gpio_direction_output() relied on
pinctrl_gpio_direction_output() to set the direction, followed by a call
to byt_gpio_set() to apply the selected value. This causes the pin to
go low between the pinctrl_gpio_direction_output() and byt_gpio_set()
calls.
Change byt_gpio_direction_output() to directly make the register
modifications itself instead. Replacing the 2 subsequent writes to the
value register with a single write.
Note that the pinctrl code does not keep track internally of the direction,
so not going through pinctrl_gpio_direction_output() is not an issue.
This issue was noticed on a Trekstor SurfTab Twin 10.1. When the panel is
already on at boot (no external monitor connected), then the i915 driver
does a gpiod_get(..., GPIOD_OUT_HIGH) for the panel-enable GPIO. The
temporarily going low of that GPIO was causing the panel to reset itself
after which it would not show an image until it was turned off and back on
again (until a full modeset was done on it). This commit fixes this.
This commit also updates the byt_gpio_direction_input() to use direct
register accesses instead of going through pinctrl_gpio_direction_input(),
to keep it consistent with byt_gpio_direction_output().
Note for backporting, this commit depends on:
commit e2b74419e5 ("pinctrl: baytrail: Replace WARN with dev_info_once
when setting direct-irq pin to output")
Cc: stable@vger.kernel.org
Fixes: 86e3ef812f ("pinctrl: baytrail: Update gpio chip operations")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is no need to repeat functionality of platform_get_irq_optional()
in the driver. Replace it with explicit call to the helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It appears that pin configuration for GPIO chip hasn't been enabled yet
due to absence of ->set_config() callback.
Enable it here for Intel Baytrail.
Fixes: c501d0b149 ("pinctrl: baytrail: Add pin control operations")
Depends-on: 2956b5d94a ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
On Cherry Trail device the interrupt pin is listed as a GpioInt ACPI
resource so we can do this without problems as long as we release the
IRQ before changing the pin to output mode.
On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource. This
works fine, but this triggers the WARN in byt_gpio_set_direction-s output
path because direct-irq support is enabled on the pin.
This commit replaces the WARN call with a dev_info_once call, fixing a
bunch of WARN splats in dmesg on each suspend/resume cycle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource.
This works fine, until the goodix driver gets rmmod-ed and then insmod-ed
again. In this case byt_gpio_disable_free() calls
byt_gpio_clear_triggering() which clears the IRQ flags and after that the
(direct) IRQ no longer triggers.
This commit fixes this by adding a check for the BYT_DIRECT_IRQ_EN flag
to byt_gpio_clear_triggering().
Note that byt_gpio_clear_triggering() only gets called from
byt_gpio_disable_free() for direct-irq enabled pins, as these are excluded
from the irq_valid mask by byt_init_irq_valid_mask().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is no need to keep pointer to struct platform_device, which is container
of struct device, because the latter is what have been used everywhere outside
of ->probe() path. In any case we may derive pointer to the container when
needed.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
After commit 5ea422750a9f ("pinctrl: baytrail: Pass irqchip when
adding gpiochip") the GPIO IRQ chip structure is being initialized
under conditional when IRQ resource has been discovered. But that
commit left aside the assignment of ->init_valid_mask() callback
that is done unconditionally.
For sake of consistency and preventing some garbage in GPIO IRQ chip
structure group initialization together.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Keeping the IRQ chip definition static shares it with multiple instances
of the GPIO chip in the system. This is bad and now we get this warning
from GPIO library:
"detected irqchip that is shared with multiple gpiochips: please fix the driver."
Hence, move the IRQ chip definition from being driver static into the struct
intel_pinctrl. So a unique IRQ chip is used for each GPIO chip instance.
Fixes: 9f573b98ca ("pinctrl: baytrail: Update irq chip operations")
Depends-on: ca8a958e2a ("pinctrl: baytrail: Pass irqchip when adding gpiochip")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When IRQ chip is instantiated via GPIO library flow, the few functions,
in particular the ACPI event registration mechanism, on some of ACPI based
platforms expect that the pin ranges are initialized to that point.
Add GPIO <-> pin mapping ranges via callback in the GPIO library flow.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Commit 39ce8150a0 ("pinctrl: baytrail: Serialize all register access")
added a spinlock around all register accesses because:
"There is a hardware issue in Intel Baytrail where concurrent GPIO register
access might result reads of 0xffffffff and writes might get dropped
completely."
Testing has shown that this does not catch all cases, there are still
2 problems remaining
1) The original fix uses a spinlock per byt_gpio device / struct,
additional testing has shown that this is not sufficient concurent
accesses to 2 different GPIO banks also suffer from the same problem.
This commit fixes this by moving to a single global lock.
2) The original fix did not add a lock around the register accesses in
the suspend/resume handling.
Since pinctrl-baytrail.c is using normal suspend/resume handlers,
interrupts are still enabled during suspend/resume handling. Nothing
should be using the GPIOs when they are being taken down, _but_ the
GPIOs themselves may still cause interrupts, which are likely to
use (read) the triggering GPIO. So we need to protect against
concurrent GPIO register accesses in the suspend/resume handlers too.
This commit fixes this by adding the missing spin_lock / unlock calls.
The 2 fixes together fix the Acer Switch 10 SW5-012 getting completely
confused after a suspend resume. The DSDT for this device has a bug
in its _LID method which reprograms the home and power button trigger-
flags requesting both high and low _level_ interrupts so the IRQs for
these 2 GPIOs continuously fire. This combined with the saving of
registers during suspend, triggers concurrent GPIO register accesses
resulting in saving 0xffffffff as pconf0 value during suspend and then
when restoring this on resume the pinmux settings get all messed up,
resulting in various I2C busses being stuck, the wifi no longer working
and often the tablet simply not coming out of suspend at all.
Cc: stable@vger.kernel.org
Fixes: 39ce8150a0 ("pinctrl: baytrail: Serialize all register access")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.4 kernel cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to the
Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver"
* tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (112 commits)
pinctrl: meson-gxbb: Fix wrong pinning definition for uart_c
pinctrl: sh-pfc: Unlock on error in sh_pfc_func_set_mux()
pinctrl: bcm: remove redundant assignment to pointer log
pinctrl: iproc: Add 'get_direction' support
pinctrl: iproc-gpio: Handle interrupts for multiple instances
pinctrl: iproc-gpio: Fix incorrect pinconf configurations
pinctrl: intel: mark intel_pin_to_gpio __maybe_unused
pinctrl: qcom: sdm845: Fix UFS_RESET pin
pinctrl: mvebu: add additional variant for standalone CP115
pinctrl: mvebu: Add CP110 missing pin functionality
dt-bindings: cp110: document the new CP115 pinctrl compatible
pinctrl: bcm2835: Pass irqchip when adding gpiochip
pinctrl: meson: meson: Add of_node_put() before return
pinctrl/gpio: Take MUX usage into account
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150l support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150b support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150 support
pinctrl: amd: disable spurious-firing GPIO IRQs
pinctrl: rza2: Include the appropriate headers
pinctrl: rza2: Drop driver use of consumer flags
...
After changing the valid_mask for the struct gpio_chip
to detect the need and presence of a valid mask with the
presence of a .init_valid_mask() callback to fill it in,
we augment the gpio_irq_chip to use the same logic.
Switch all driver using the gpio_irq_chio valid_mask
over to this new method.
This makes sure the valid_mask for the gpio_irq_chip gets
filled in when we add the gpio_chip, which makes it a
little easier to switch over drivers using the old
way of setting up gpio_irq_chip over to the new method
of passing the gpio_irq_chip along with the gpio_chip.
(See drivers/gpio/TODO for details.)
Cc: Joel Stanley <joel@jms.id.au>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Link: https://lore.kernel.org/r/20190904140104.32426-1-linus.walleij@linaro.org
We have some data structures duplicated across the drivers.
Let's deduplicate them by using ones that being provided by
pinctrl-intel.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
saved-context in byt_gpio_probe is allocated via devm_kcalloc and is
used without checking for NULL in later functions. This patch avoids
such a scenario.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
These drivers are GPIO drivers, and the do not need to use the
legacy header in <linux/gpio.h>, go directly for
<linux/gpio/driver.h> instead.
Replace any use of GPIOF_* with 0/1, these flags are for
consumers, not drivers.
Get rid of a few gpio_to_irq() users that was littering
around the place, use local callbacks or avoid using it at
all.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1292308 ("Missing break in switch")
Addresses-Coverity-ID: 1292309 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On some systems, some PCB traces attached to GpioInts are routed in such
a way that they pick up enough interference to constantly (many times per
second) trigger.
Enabling glitch-filtering fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
WARN_ON causes a backtrace to get logged which is only useful for
kernel bugs. For signalling a firmware bug dev_warn(dev, FW_BUG "...")
should be used.
This fixes users running userspace software to monitor kernel oopses
getting a false positive bug-report every boot because of the wrong
use of WARN_ON.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull pin control updates from Linus Walleij:
"Pin control bulk changes for the v4.11 kernel cycle.
Core changes:
- Switch the generic pin config argument from 16 to 24 bits, only use
8 bits for the configuration type. We might need to encode more
information about a certain setting than we need to encode
different generic settings.
- Add a cross-talk API to the pin control GPIO back-end, utilizing
pinctrl_gpio_set_config() from GPIO drivers that want to set up a
certain pin configuration in the back-end.
This also includes the .set_config() refactoring of the GPIO chips,
so that they pass a generic configuration for things like
debouncing and single ended (typically open drain). This change has
also been merged in an immutable branch to the GPIO tree.
- Take hogs with a delayed work, so that we finalize probing a pin
controller before trying to get any hogs.
- For pin controllers putting all group and function definitions into
the device tree, we now have generic code to deal with this and it
is used in two drivers so far.
- Simplifications of the pin request conflict check.
- Make dt_free_map() optional.
Updates to drivers:
- pinctrl-single now use the generic helpers to generate dynamic
group and function tables from the device tree.
- Texas Instruments IOdelay configuration driver add-on to
pinctrl-single.
- i.MX: use radix trees to store groups and functions, use the new
generic group and function helpers to manage them.
- Intel: add support for hardware debouncing and 1K pull-down. New
subdriver for the Gemini Lake SoC.
- Renesas SH-PFC: drive strength and bias support, CAN bus muxing,
MSIOF, SDHI, HSCIF for r8a7796. Gyro-ADC supporton r8a7791.
- Aspeed: use syscon cross-dependencies to set up related bits in the
LPC host controller and display controller.
- Aspeed: finalize G4 and G5 support. Fix mux configuration on GPIOs.
Add banks Y, Z, AA, AB and AC.
- AMD: support additional GPIO.
- STM32: set this controller to strict muxing mode. STM32H743 MCU
support.
- Allwinner sunxi: deep simplifications on how to support subvariants
of SoCs without adding to much SoC-specific data for each
subvariant, especially for sun5i variants. New driver for V3s SoCs.
New driver for the H5 SoC. Support A31/A31s variants with the new
variant framework.
- Mvebu: simplifications to use a MMIO and regmap abstraction. New
subdrivers for the 98DX3236, 98DX5241 SoCs.
- Samsung Exynos: delete Exynos4415 support. Add crosstalk to the SoC
driver to access regmaps. Add infrastructure for pin-bank retention
control. Clean out the pin retention control from
arch/arm/mach-exynos and arch/arm/mach-s5p and put it properly in
the Samsung pin control driver(s).
- Meson: add HDMI HPD/DDC pins. Add pwm_ao_b pin.
- Qualcomm: use raw spinlock variants: this makes the qualcomm driver
realtime-safe"
* tag 'pinctrl-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (111 commits)
pinctrl: samsung: Fix return value check in samsung_pinctrl_get_soc_data()
pinctrl: intel: unlock on error in intel_config_set_pull()
pinctrl: berlin: make bool drivers explicitly non-modular
pinctrl: spear: make bool drivers explicitly non-modular
pinctrl: mvebu: make bool drivers explicitly non-modular
pinctrl: sunxi: make sun5i explicitly non-modular
pinctrl: sunxi: Remove stray printk call in sun5i driver's probe function
pinctrl: samsung: mark PM functions as __maybe_unused
pinctrl: sunxi: Remove redundant A31s pinctrl driver
pinctrl: sunxi: Support A31/A31s with pinctrl variants
pinctrl: Amend bindings for STM32 pinctrl
pinctrl: Add STM32 pinctrl driver DT bindings
pinctrl: stm32: Add STM32H743 MCU support
include: dt-bindings: Add STM32H7 pinctrl DT defines
gpio: aspeed: Remove dependence on GPIOF_* macros
pinctrl: stm32: fix bad location of gpiochip_lock_as_irq
drivers: pinctrl: add driver for Allwinner H5 SoC
pinctrl: intel: Add Intel Gemini Lake pin controller support
pinctrl: intel: Add support for 1k additional pull-down
pinctrl: intel: Add support for hardware debouncer
...
Debounce value is set globally per community. Otherwise user will easily
get a kernel crash when they start using the feature:
BUG: unable to handle kernel paging request at ffffc900003be000
IP: byt_gpio_dbg_show+0xa9/0x430
Make it clear in byt_gpio_reg().
Note that this fix just prevents kernel to crash, but doesn't make any
difference to the existing logic. It means the last caller will win the
trade and debounce value will be configured accordingly. The actual
logic fix needs to be thought about and it's not as important as crash
fix. That's why the latter goes separately and right now.
Fixes: 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
Cc: Cristina Ciocan <cristina.ciocan@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit 04ff5a095d ("pinctrl: baytrail: Rectify debounce support")
almost fixes the logic of debuonce but missed couple of things, i.e.
typo in mask when disabling debounce and lack of enabling it back.
This patch addresses above issues.
Reported-by: Jean Delvare <jdelvare@suse.de>
Fixes: 04ff5a095d ("pinctrl: baytrail: Rectify debounce support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Apparently each GPIO pad's register are 16 bytes, so multiply the pad_map
by that. The same is done in byt_gpio_reg the only other place where
pad_map is used.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When DIRECT_IRQ_EN is set, the pin is routed directly to the IO-APIC bypassing
the GPIO driver completely. However, the mask register is still used to
determine if the pin is supposed to generate IRQ or not.
So with commit 3ae02c14d9 the IRQ core masks all IRQs (because of
handle_bad_irq()) the pin connected to the touchscreen gets masked as well and
hence no interrupts.
To make this all work as expected we do not add those GPIOs to the IRQ domain
that can actually propagate interrupts.
Fixes: 3ae02c14d9 ("pinctrl: intel: set default handler to be handle_bad_irq()")
Reported-by: Robert R. Howell <rhowell@uwyo.edu>
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
implements debounce for Baytrail pin control, but seems wasn't tested properly.
The register which keeps debounce value is separated from the configuration
one. Writing wrong values to the latter will guarantee wrong behaviour of the
driver and even might break something physically.
Besides above there is missed case how to disable it, which is actually done
through the bit in configuration register.
Rectify implementation here by using proper register for debounce value.
Fixes: 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
Cc: Cristina Ciocan <cristina.ciocan@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Initialize the spinlock before using it.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.8.0-dwc-bisect #4
Hardware name: Intel Corp. VALLEYVIEW C0 PLATFORM/BYT-T FFD8, BIOS BLAKFF81.X64.0088.R10.1403240443 FFD8_X64_R_2014_13_1_00 03/24/2014
0000000000000000 ffff8800788ff770 ffffffff8133d597 0000000000000000
0000000000000000 ffff8800788ff7e0 ffffffff810cfb9e 0000000000000002
ffff8800788ff7d0 ffffffff8205b600 0000000000000002 ffff8800788ff7f0
Call Trace:
[<ffffffff8133d597>] dump_stack+0x67/0x90
[<ffffffff810cfb9e>] register_lock_class+0x52e/0x540
[<ffffffff810d2081>] __lock_acquire+0x81/0x16b0
[<ffffffff810cede1>] ? save_trace+0x41/0xd0
[<ffffffff810d33b2>] ? __lock_acquire+0x13b2/0x16b0
[<ffffffff810cf05a>] ? __lock_is_held+0x4a/0x70
[<ffffffff810d3b1a>] lock_acquire+0xba/0x220
[<ffffffff8136f1fe>] ? byt_gpio_get_direction+0x3e/0x80
[<ffffffff81631567>] _raw_spin_lock_irqsave+0x47/0x60
[<ffffffff8136f1fe>] ? byt_gpio_get_direction+0x3e/0x80
[<ffffffff8136f1fe>] byt_gpio_get_direction+0x3e/0x80
[<ffffffff813740a9>] gpiochip_add_data+0x319/0x7d0
[<ffffffff81631723>] ? _raw_spin_unlock_irqrestore+0x43/0x70
[<ffffffff8136fe3b>] byt_pinctrl_probe+0x2fb/0x620
[<ffffffff8142fb0c>] platform_drv_probe+0x3c/0xa0
...
Based on the diff it looks like the problem was introduced in
commit 71e6ca61e8 ("pinctrl: baytrail: Register pin control handling")
but I wasn't able to verify that empirically as the parent commit
just oopsed when I tried to boot it.
Cc: Cristina Ciocan <cristina.ciocan@intel.com>
Cc: stable@vger.kernel.org
Fixes: 71e6ca61e8 ("pinctrl: baytrail: Register pin control handling")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.8 kernel cycle.
Nothing stands out as especially exiting: new drivers, new subdrivers,
lots of cleanups and incremental features.
Business as usual.
New drivers:
- New driver for Oxnas pin control and GPIO. This ARM-based chipset
is used in a few storage (NAS) type devices.
- New driver for the MAX77620/MAX20024 pin controller portions.
- New driver for the Intel Merrifield pin controller.
New subdrivers:
- New subdriver for the Qualcomm MDM9615
- New subdriver for the STM32F746 MCU
- New subdriver for the Broadcom NSP SoC.
Cleanups:
- Demodularization of bool compiled-in drivers.
Apart from this there is just regular incremental improvements to a
lot of drivers, especially Uniphier and PFC"
* tag 'pinctrl-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (131 commits)
pinctrl: fix pincontrol definition for marvell
pinctrl: xway: fix typo
Revert "pinctrl: amd: make it explicitly non-modular"
pinctrl: iproc: Add NSP and Stingray GPIO support
pinctrl: Update iProc GPIO DT bindings
pinctrl: bcm: add OF dependencies
pinctrl: ns2: remove redundant dev_err call in ns2_pinmux_probe()
pinctrl: Add STM32F746 MCU support
pinctrl: intel: Protect set wake flow by spin lock
pinctrl: nsp: remove redundant dev_err call in nsp_pinmux_probe()
pinctrl: uniphier: add Ethernet pin-mux settings
sh-pfc: Use PTR_ERR_OR_ZERO() to simplify the code
pinctrl: ns2: fix return value check in ns2_pinmux_probe()
pinctrl: qcom: update DT bindings with ebi2 groups
pinctrl: qcom: establish proper EBI2 pin groups
pinctrl: imx21: Remove the MODULE_DEVICE_TABLE() macro
Documentation: dt: Add new compatible to STM32 pinctrl driver bindings
includes: dt-bindings: Add STM32F746 pinctrl DT bindings
pinctrl: sunxi: fix nand0 function name for sun8i
pinctrl: uniphier: remove pointless pin-mux settings for PH1-LD11
...
