If we have only 2k RBs like on the latest (AX210) hardware, then
even on x86 where PAGE_SIZE is 4k we currently waste half of the
memory.
If this is the case, return partial pages from the allocator and
track the offset in each RBD (to be able to find the data in them
and remap them later.)
This might also address other platforms with larger PAGE_SIZE by
putting more RBs into a single large page.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't need to map *everything* of the RX buffers, we won't use
that much, map only the part we're going to use. This save some
IOMMU space (if applicable and it can deal with that) and also
prepares a bit for mapping partial pages for 2K buffers later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For HE-capable devices, we need to allocate more receive buffers as
there could be 256 frames aggregated into a single A-MPDU, and then
they might contain A-MSDUs as well. Until 22000 family, the devices
are able to put multiple frames into a single RB and the default RB
size is 4k, but starting from AX210 family this is no longer true.
On the other hand, those newer devices only use 2k receive buffers
(by default).
Modify the code and configuration to allocate an appropriate number
of RBs depending on the device capabilities:
* 4096 for AX210 HE devices, which use 2k buffers by default,
* 2048 for 22000 family devices which use 4k buffers by default,
* 512 for existing 9000 family devices, which doesn't really
change anything since that's the default before this patch,
* 512 also for AX210/22000 family devices that don't do HE.
Theoretically, for devices lower than AX210, we wouldn't have to
allocate that many RBs if the RB size was manually increased, but
to support that the code got more complex, and it didn't really
seem necessary as that's a use case for monitor mode only, where
hopefully the wasted memory isn't really much of a concern.
Note that AX210 devices actually support bigger than 12-bit VID,
which is required here as we want to allocate 4096 buffers plus
some for quick recycling, so adjust the code for that as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new API requires the driver to config the supported frame format
(legacy, HT, VHT etc.).
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new API requires the driver to set the frame format
(legacy, HT, VHT etc.) to be used for the measurement.
The new API also supports 11az and secured measurement, but
these are not supported by the driver for now.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
After more investigation on the hardware side, it appears that the
hardware bug regarding 2^32 boundary reaching/crossing also affects
other uses of the DMA engine, in particular the ones triggered by
the context-info (image loader) mechanism.
It also turns out that the bug only affects devices with gen2 TX
hardware engine, so we don't need to change context info for gen3.
The TX path workarounds are simpler to still keep for both though.
Add the workaround to that code as well; this is a lot simpler as
we have just a single way to allocate DMA memory there.
I made the algorithm recursive (with a small limit) since it's
actually (almost) impossible to hit this today - dma_alloc_coherent
is currently documented to always return 32-bit addressable memory
regardless of the DMA mask for it, and so we could only get REALLY
unlucky to get the very last page in that area.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When receiving a new MCC driver get all the data about the new country
code and its regulatory information.
Mistakenly, we ignored the cap field, which includes global regulatory
information which should be applies to every channel.
Fix it.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we have offloaded rate scaling, which is always true for those
devices supporting HE, then report the TX rate directly from the
data the firmware gives us, instead of only passing it to mac80211
on frame status only and for it to track it.
First of all, this makes us always report the last good rate that
the rate scaling algorithm picked, which is better than reporting
the last rate for any frame since management frames etc. are sent
with very low rates and could interfere.
Additionally, this allows us to properly report HE rates, though
in case there's a lot of trigger-based traffic, we don't get any
choice in the rates and don't report that properly right now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We had a check on !NVM_EXT and then a check for NVM_SDP in the else
block of this if. The else block, obviously, could only be reached if
using NVM_EXT, so it would never be NVM_SDP.
Fix that by checking whether the nvm_type is IWL_NVM instead of
checking for !IWL_NVM_EXT to solve this issue.
Reported-by: Stefan Sperling <stsp@stsp.name>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the allocation loop, "pages" will never become zero (because of the
DIV_ROUND_UP), so if we can't allocate any size and pages becomes 1,
we will keep trying to allocate 1 page until it succeeds. And in that
case, as coverity reported, block will never be NULL.
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Addresses-Coverity-ID: 1487402 ("Control flow issues")
Fixes: 14124b2578 ("iwlwifi: dbg_ini: implement monitor allocation flow")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: 14124b2578 ("iwlwifi: dbg_ini: implement monitor allocation flow")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As noted in the previous commit, due to the way we allocate the
dev_cmd headers with 324 byte size, and 4/8 byte alignment, the
part we use of them (bytes 20..40-68) could still cross a page
and thus 2^32 boundary.
Address this by using alignment to ensure that the allocation
cannot cross a page boundary, on hardware that's affected. To
make that not cause more memory consumption, reduce the size of
the allocations to the necessary size - we go from 324 bytes in
each allocation to 60/68 on gen2 depending on family, and ~120
or so on gen1 (so on gen1 it's a pure reduction in size, since
we don't need alignment there).
To avoid size and clearing issues, add a new structure that's
just the header, and use kmem_cache_zalloc().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Warn if the DMA bug is going to happen. We don't have a good
way of actually aborting in this case and we have workarounds
in place for the cases where it happens, but in order to not
be surprised add a safety-check and warn.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's a hardware bug in the flow handler (DMA engine), if the
address + len of some TB wraps around a 2^32 boundary, the carry
bit is then carried over into the next TB.
Work around this by copying the data to a new page when we find
this situation, and then copy it in a way that we cannot hit the
very end of the page.
To be able to free the new page again later we need to chain it
to the TSO page, use the last pointer there to make sure we can
never use the page fully for DMA, and thus cannot cause the same
overflow situation on this page.
This leaves a few potential places (where we didn't observe the
problem) unaddressed:
* The second TB could reach or cross the end of a page (and thus
2^32) due to the way we allocate the dev_cmd for the header
* For host commands, a similar thing could happen since they're
just kmalloc().
We'll address these in further commits.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Kalle Valo says:
====================
wireless-drivers-next patches for v5.6
First set of patches for v5.6. The biggest thing here is of course the
new driver ath11k but also new features for other drivers as well a
myriad of bug fixes.
Major changes:
ath11k
* a new driver for Qualcomm Wi-Fi 6 (IEEE 802.11ax) devices
ath10k
* significant improvements on receive throughput and firmware download
with SDIO bus
* report signal strength for each chain also on SDIO
* set max mtu to 1500 on SDIO devices
brcmfmac
* add support for BCM4359 SDIO chipset
wil6210
* support set_multicast_to_unicast cfg80211 operation
* support set_cqm_rssi_config cfg80211 operation
wcn36xx
* disable HW_CONNECTION_MONITOR as firmware is buggy
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Before we start looping over the internal TX FIFOs increase the fifo
number, but that's incorrect and causes a FIFO to be skipped. This is
probably due to a copy and paste from the previous loop.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This fixes a long-standing bug - we haven't been able to check the
firmware image that was loaded for D3/not-D3 since the introduction
of the unified image...
Fix this by keeping a status flag for D3 instead of checking for
the firmware image that's loaded.
This reduces occurrences of checks for IWL_UCODE_WOWLAN to just the
code that actually loads the image or deals with it in other ways.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the tracking that records the page in the SKB for later
free (refcount decrement) into the get_page_hdr() function
for better code reuse.
While at it, also add an assertion that this doesn't overwrite
any existing page pointer in the skb.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
we should not send the PPAG (Per-Platform Antenna Gain)
command to FW unless the platform has this ACPI table and it was
read and validated during the init flow. also no need to send the
command if the feature is disabled, so check if enabled before
sending, as if there is no valid table the feature is disabled.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Kalle Valo says:
====================
wireless-drivers fixes for v5.5
First set of fixes for v5.5. Fixing security issues, some regressions
and few major bugs.
mwifiex
* security fix for handling country Information Elements (CVE-2019-14895)
* security fix for handling TDLS Information Elements
ath9k
* fix endian issue with ath9k_pci_owl_loader
mt76
* fix default mac address handling
iwlwifi
* fix merge damage which lead to firmware crashing during boot on some devices
* fix device initialisation regression on some devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to reset the NIC after setting the bits to enable power
gating and that cannot be done too late in the flow otherwise it
cleans other registers and things that were already configured,
causing initialization to fail.
In order to fix this, move the function to the common code in trans.c
so it can be called directly from there at an earlier point, just
after the reset we already do during initialization.
Fixes: 9a47cb9883 ("iwlwifi: pcie: add workaround for power gating in integrated 22000")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=205719
Cc: stable@ver.kernel.org # 5.4+
Reported-by: Anders Kaseorg <andersk@mit.edu>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit 968dcfb490.
Both that commit and commit 809805a820
attempted to fix the same bug (dead assignments to the local variable
cfg), but they did so in incompatible ways. When they were both merged,
independently of each other, the combination actually caused the bug to
reappear, leading to a firmware crash on boot for some cards.
https://bugzilla.kernel.org/show_bug.cgi?id=205719
Signed-off-by: Anders Kaseorg <andersk@mit.edu>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 6570bc79c0 ("net: core: use listified Rx for GRO_NORMAL in
napi_gro_receive()") has applied batched GRO_NORMAL packets processing
to all napi_gro_receive() users, including mac80211-based drivers.
However, this change has led to a regression in iwlwifi driver [1][2] as
it is required for NAPI users to call napi_complete_done() or
napi_complete() and the end of every polling iteration, whilst iwlwifi
doesn't use NAPI scheduling at all and just calls napi_gro_flush().
In that particular case, packets which have not been already flushed
from napi->rx_list stall in it until at least next Rx cycle.
Fix this by adding a manual flushing of the list to iwlwifi driver right
before napi_gro_flush() call to mimic napi_complete() logics.
I prefer to open-code gro_normal_list() rather than exporting it for 2
reasons:
* to prevent from using it and napi_gro_flush() in any new drivers,
as it is the *really* bad way to use NAPI that should be avoided;
* to keep gro_normal_list() static and don't lose any CC optimizations.
I also don't add the "Fixes:" tag as the mentioned commit was only a
trigger that only exposed an improper usage of NAPI in this particular
driver.
[1] https://lore.kernel.org/netdev/PSXP216MB04388962C411CD0B17A86F47804A0@PSXP216MB0438.KORP216.PROD.OUTLOOK.COM
[2] https://bugzilla.kernel.org/show_bug.cgi?id=205647
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Reported-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Tested-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Reviewed-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kasprintf() can fail, we should check the return value.
Fixes: 5ed540aecc ("iwlwifi: use mac80211 throughput trigger")
Fixes: 8ca151b568 ("iwlwifi: add the MVM driver")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no multicast wake lock in the driver, remove the comment
that refers to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We trace the whole TFD with all TBs when in iwlwifi_dev_tx,
but sometimes we add TBs to it later and then we don't have
any of this data. Trace the I/O virtual address (IOVA) (it
can be the physical address, or as returned by the IOMMU)
here to aid debugging the DMA flows.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is no need to check 'priv->bt_ant_couple_ok' twice in
rs_bt_update_lq(). The second check is always true. Thus, the
expression can be simplified.
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This makes it easier for user-space to know how many antennas the
radio has. Seems to work with the AX200 radio, at least.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is a little less efficient now as it's known to be a
multiqueue device in this function, but a future patch will
have to use a variable here anyway, so use rxq->queue_size
now instead to make it clearer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This email alias (ilw@linux.intel.com) hasn't been functional
for probably closer to a decade than not, remove it. It's not
really clear to me how this ended up in new code though.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
1. Modify channel config flags to be used for legacy bands channels
as well, to indicate SSIDs elements from ssidIEsArray.
2. Add new general flag.
3. Remove ssidNum from probe params.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the implementation of SKBs with fraglist was sent upstream, a
merge-damage occurred and half the patch was not applied.
This causes problems in high-throughput situations with AX200 devices,
including low throughput and FW crashes.
Introduce the part that was missing from the original patch.
Fixes: 0044f1716c ("iwlwifi: pcie: support transmitting SKBs with fraglist")
Cc: stable@vger.kernel.org # 4.20+
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[ This patch was created by me, but the original author of this code
is Johannes, so his s-o-b is here and he's marked as the author of
the patch. ]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/intel/ipw2x00/ipw2100.c: In function shim__set_security:
drivers/net/wireless/intel/ipw2x00/ipw2100.c:5582:9: warning: variable force_update set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/intel/ipw2x00/ipw2200.c: In function ipw_wx_set_mlme:
drivers/net/wireless/intel/ipw2x00/ipw2200.c:6805:9: warning: variable reason set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The code now compiles without ACPI, but there's a warning since
iwl_mvm_get_ppag_table() isn't used, and iwl_mvm_ppag_init() must
not unconditionally fail but return success instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is dead code, nothing uses the IWL_DEVICE_22560 macro and
thus nothing every uses IWL_DEVICE_FAMILY_22560. Remove it all.
While at it, remove some code and definitions used only in this
case, and clean up some comments/names that still refer to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The current budget of 2000mA is preventing us from reaching maximum
throughput. According to our system engineers, we can increase the
maximum budget to 2400mA to solve this problem.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are various of flows which require tids flushing
(disconnection, suspend, etc...).
Currently, when the driver instructs the FW to flush
he masks all the data tids(0-7).
However, the driver doesn't set the management tid (#15)
which cause the FW not to flush it.
When the FW tries to remove the mgmt queue he throws an assert
since it is not an empty queue.
instead of just set only the data tids set everything and let
the FW ignore the invalid tids.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Refactored the SAR related functions from iwlmvm to acpi
in order to make it shared between different opmodes
in addition to removing unused variable ppag_rev.
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
