The burst length is configured in VIU_OSD1_FIFO_CTRL_STAT[31] and
VIU_OSD1_FIFO_CTRL_STAT[11:10]. The public S905D3 datasheet describes
this as:
- 0x0 = up to 24 per burst
- 0x1 = up to 32 per burst
- 0x2 = up to 48 per burst
- 0x3 = up to 64 per burst
- 0x4 = up to 96 per burst
- 0x5 = up to 128 per burst
The lower two bits map to VIU_OSD1_FIFO_CTRL_STAT[11:10] while the upper
bit maps to VIU_OSD1_FIFO_CTRL_STAT[31].
Replace meson_viu_osd_burst_length_reg() with pre-defined macros which
set these values. meson_viu_osd_burst_length_reg() always returned 0
(for the two used values: 32 and 64 at least) and thus incorrectly set
the burst size to 24.
Fixes: 147ae1cbaa ("drm: meson: viu: use proper macros instead of magic constants")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200620155752.21065-1-martin.blumenstingl@googlemail.com
The Amlogic S805X/Y uses the same die as the S905X, but with more
limited graphics capabilities.
This adds a soc version detection adding specific limitations on the HDMI
mode selections.
Here, we limit to HDMI 1.2a max HDMI PHY clock frequency.
Changes sinces v1:
- Moved frequency check in the vclk code, and also checks DMT modes
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[narmstrong: fixed commit message with HDMI 1.2a instead of HDMI 1.3a]
Link: https://patchwork.freedesktop.org/patch/msgid/20200428092147.13698-1-narmstrong@baylibre.com
This patch adds support for the YUV420 output from the Amlogic Meson SoCs
Video Processing Unit to the HDMI Controller.
The YUV420 is obtained by generating a YUV444 pixel stream like
the classic HDMI display modes, but then the Video Encoder output
can be configured to down-sample the YUV444 pixel stream to a YUV420
stream.
In addition if pixel stream down-sampling, the Y Cb Cr components must
also be mapped differently to align with the HDMI2.0 specifications.
This mode needs a different clock generation scheme since the TMDS PHY
clock must match the 10x ratio with the YUV420 pixel clock, but
the video encoder must run at 2x the pixel clock.
This patch enables the bridge bus format negociation, and handles
the YUV420 case if selected by the negociation.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-12-narmstrong@baylibre.com
This patch adds clocking support for the YUV420 output from the
Amlogic Meson SoCs Video Processing Unit to the HDMI Controller.
The YUV420 is obtained by generating a YUV444 pixel stream like
the classic HDMI display modes, but then the Video Encoder output
can be configured to down-sample the YUV444 pixel stream to a YUV420
stream.
This mode needs a different clock generation scheme since the TMDS PHY
clock must match the 10x ratio with the YUV420 pixel clock, but
the video encoder must run at 2x the pixel clock.
This patch adds the TMDS PHY clock value in all the video clock setup
in order to better support these specific uses cases and switch
to the Common Clock framework for clocks handling in the future.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-11-narmstrong@baylibre.com
This patch adds encoding support for the YUV420 output from the
Amlogic Meson SoCs Video Processing Unit to the HDMI Controller.
The YUV420 is obtained by generating a YUV444 pixel stream like
the classic HDMI display modes, but then the Video Encoder output
can be configured to down-sample the YUV444 pixel stream to a YUV420
stream.
In addition if pixel stream down-sampling, the Y Cb Cr components must
also be mapped differently to align with the HDMI2.0 specifications.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-10-narmstrong@baylibre.com
Casting a pointer to dma_addr_t produces a warning:
drivers/gpu/drm/meson/meson_rdma.c: In function 'meson_rdma_free':
drivers/gpu/drm/meson/meson_rdma.c:59:25: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
priv->rdma.addr_phys = (dma_addr_t)NULL;
In this case, it's worse because the variable name has the suffix
'_phys', which often indicates a phys_addr_t rather than dma_addr_t,
i.e. yet another incompatible type.
Change it to use consistent naming and avoid NULL.
Fixes: 63fba242c4 ("drm/meson: add RDMA module driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200107214653.1173199-1-arnd@arndb.de
drm-misc-next for v5.6:
UAPI Changes:
- Add support for DMA-BUF HEAPS.
Cross-subsystem Changes:
- mipi dsi definition updates, pulled into drm-intel as well.
- Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim.
- Remove support for dma-buf kmap/kunmap.
- Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well.
Core Changes:
- Small cleanups to ttm.
- Fix SCDC definition.
- Assorted cleanups to core.
- Add todo to remove load/unload hooks, and use generic fbdev emulation.
- Assorted documentation updates.
- Use blocking ww lock in ttm fault handler.
- Remove drm_fb_helper_fbdev_setup/teardown.
- Warning fixes with W=1 for atomic.
- Use drm_debug_enabled() instead of drm_debug flag testing in various drivers.
- Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted)
- Various kconfig indentation fixes in core and drivers.
- Fix freeing transactions in dp-mst correctly.
- Sean Paul is steping down as core maintainer. :-(
- Add lockdep annotations for atomic locks vs dma-resv.
- Prevent use-after-free for a bad job in drm_scheduler.
- Fill out all block sizes in the P01x and P210 definitions.
- Avoid division by zero in drm/rect, and fix bounds.
- Add drm/rect selftests.
- Add aspect ratio and alternate clocks for HDMI 4k modes.
- Add todo for drm_framebuffer_funcs and fb_create cleanup.
- Drop DRM_AUTH for prime import/export ioctls.
- Clear DP-MST payload id tables downstream when initializating.
- Fix for DSC throughput definition.
- Add extra FEC definitions.
- Fix fake offset in drm_gem_object_funs.mmap.
- Stop using encoder->bridge in core directly
- Handle bridge chaining slightly better.
- Add backlight support to drm/panel, and use it in many panel drivers.
- Increase max number of y420 modes from 128 to 256, as preparation to add the new modes.
Driver Changes:
- Small fixes all over.
- Fix documentation in vkms.
- Fix mmap_sem vs dma_resv in nouveau.
- Small cleanup in komeda.
- Add page flip support in gma500 for psb/cdv.
- Add ddc symlink in the connector sysfs directory for many drivers.
- Add support for analogic an6345, and fix small bugs in it.
- Add atomic modesetting support to ast.
- Fix radeon fault handler VMA race.
- Switch udl to use generic shmem helpers.
- Unconditional vblank handling for mcde.
- Miscellaneous fixes to mcde.
- Tweak debug output from komeda using debugfs.
- Add gamma and color transform support to komeda for DOU-IPS.
- Add support for sony acx424AKP panel.
- Various small cleanups to gma500.
- Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation.
- Add support for Logic PD Type 28 panel.
- Use drm_panel_* wrapper functions in exynos/tegra/msm.
- Add devicetree bindings for generic DSI panels.
- Don't include drm_pci.h directly in many drivers.
- Add support for begin/end_cpu_access in udmabuf.
- Stop using drm_get_pci_dev in gma500 and mga200.
- Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access.
- Add devfreq thermal support to panfrost.
- Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager.
- meson: Add support for OSD1 plane AFBC commit.
- Stop displaying garbage when toggling ast primary plane on/off.
- More cleanups and fixes to UDL.
- Add D32 suport to komeda.
- Remove globle copy of drm_dev in gma500.
- Add support for Boe Himax8279d MIPI-DSI LCD panel.
- Add support for ingenic JZ4770 panel.
- Small null pointer deference fix in ingenic.
- Remove support for the special tfp420 driver, as there is a generic way to do it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ba73535a-9334-5302-2e1f-5208bd7390bd@linux.intel.com
Finally, setup the VIU registers and start the AFBC decoder to support
displaying AFBC encoded buffers on Amlogic GXM and G12A SoCs.
The RDMA is used here to reset and program the AFBC decoder unit
on each vsync without involving the interrupt handler that can
be masked for a long period of time, producing display glitches.
The vsync irq must still be left enabled otherwise the RDMA modules isn't
trigerred when the interrupt line is masked.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191021091509.3864-10-narmstrong@baylibre.com
This adds all the OSD configuration plumbing to support the AFBC decoders
path to display of the OSD1 plane.
The Amlogic GXM and G12A AFBC decoders are integrated very differently.
The Amlogic GXM has a direct output path to the OSD1 VIU pixel input,
because the GXM AFBC decoder seem to be a custom IP developed by Amlogic.
On the other side, the Amlogic G12A AFBC decoder seems to be an external
IP that emit pixels on an AXI master hooked to a "Mali Unpack" block
feeding the OSD1 VIU pixel input.
This uses a weird "0x1000000" internal HW physical address on both
sides to transfer the pixels.
For Amlogic GXM, the supported pixel formats are the same as the normal
linear OSD1 mode.
On the other side, Amlogic added support for all AFBC v1.2 formats for
the G12A AFBC integration.
For simplicity, we stick to the already supported formats for now.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191021091509.3864-7-narmstrong@baylibre.com
This adds the driver for the ARM Framebuffer Compression decoders found
in the Amlogic GXM and G12A SoCs.
The Amlogic GXM and G12A AFBC decoder are totally different, the GXM only
handling only the AFBC v1.0 modes and the G12A decoder handling the
AFBC v1.2 modes.
The G12A AFBC decoder is an external IP integrated in the video pipeline,
and the GXM AFBC decoder seems to the an Amlogic custom decoder more
tighly integrated in the video pipeline.
The GXM AFBC decoder can handle only one AFBC plane for 2 available
OSD planes available in HW, and the G12A AFBC decoder can handle up
to 4 AFBC planes for up to 3 OSD planes available in HW.
The Amlogic GXM supports 16x16 SPARSE and 16x16 SPLIT AFBC buffers up
to 4k.
On the other side, for G12A SPLIT is mandatory in 16x16 block mode, but
for 4k modes 32x8+SPLIT AFBC buffers is manadatory for performances reasons.
The RDMA is used here to reset and program the AFBC decoder unit
on each vsync without involving the interrupt handler that can
be masked for a long period of time, producing display glitches.
For this we use the meson_rdma_writel_sync() which adds the register
write tuple (VPU register offset and register value) to the RDMA buffer
and write the value to the HW.
When enabled, the RDMA is enabled to rewrite the same sequence at the
next VSYNC event, until a new buffer is committed to the OSD plane.
Then the Amlogic G12A is switched to RDMA, the Amlogic GXM Decoder
doesn't need a reset/reprogram at each vsync, but needs to keep the
vsync interrupt enabled to trigger the RDMA module.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
[narmstrong: fixed typo in commit log]
Link: https://patchwork.freedesktop.org/patch/msgid/20191021091509.3864-6-narmstrong@baylibre.com
The VPU embeds a "Register DMA" that can write a sequence of registers
on the VPU AHB bus, either manually or triggered by an internal IRQ
event like VSYNC or a line input counter.
The initial implementation handles a single channel (over 8), triggered
by the VSYNC irq and does not handle the RDMA irq.
The RDMA will be usefull to reset and program the AFBC decoder unit
on each vsync without involving the interrupt handler that can
be masked for a log period of time, producing display glitches.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191021091509.3864-5-narmstrong@baylibre.com
With commit 222ec1618c ("drm: Add aspect ratio parsing in DRM
layer") the drm core started honoring the picture_aspect_ratio field
when comparing two drm_display_modes. Prior to that it was ignored.
When the CVBS encoder driver was initially submitted there was no aspect
ratio check.
Switch from drm_mode_equal() to drm_mode_match() without
DRM_MODE_MATCH_ASPECT_RATIO to fix "kmscube" and X.org output using the
CVBS connector. When (for example) kmscube sets the output mode when
using the CVBS connector it passes HDMI_PICTURE_ASPECT_NONE, making the
drm_mode_equal() fail as it include the aspect ratio.
Prior to this patch kmscube reported:
failed to set mode: Invalid argument
The CVBS mode checking in the sun4i (drivers/gpu/drm/sun4i/sun4i_tv.c
sun4i_tv_mode_to_drm_mode) and ZTE (drivers/gpu/drm/zte/zx_tvenc.c
tvenc_mode_{pal,ntsc}) drivers don't set the "picture_aspect_ratio" at
all. The Meson VPU driver does not rely on the aspect ratio for the CVBS
output so we can safely decouple it from the hdmi_picture_aspect
setting.
Cc: <stable@vger.kernel.org>
Fixes: 222ec1618c ("drm: Add aspect ratio parsing in DRM layer")
Fixes: bbbe775ec5 ("drm: Add support for Amlogic Meson Graphic Controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: squashed with drm: meson: venc: cvbs: deduplicate the meson_cvbs_mode lookup code]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191208171832.1064772-3-martin.blumenstingl@googlemail.com
This patch add new macros which are used to set the following
registers:
- ENCI_CFILT_CTRL
- ENCI_CFILT_CTRL2
- ENCI_MACV_MAX_AMP
- ENCI_VIDEO_MODE_ADV
- ENCI_VFIFO2VD_CTL
- ENCI_VIDEO_EN
- ENCP_VIDEO_MODE
- VPU_HDMI_SETTING
- VENC_UPSAMPLE_CTRL0
- VENC_UPSAMPLE_CTRL1
- VENC_UPSAMPLE_CTRL2
- VENC_VDAC_FIFO_CTRL
- VENC_VDAC_DAC0_FILT_CTRL0
- VENC_INTCTRL
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/86r27j82ef.fsf@baylibre.com
This patch add new macros which are used to set the following
registers:
- VIU_SW_RESET
- VIU_OSD1_CTRL_STAT
- VIU_OSD2_CTRL_STAT
- VIU_OSD1_FIFO_CTRL_STAT
- VIU_OSD2_FIFO_CTRL_STAT
- VIU_MISC_CTRL0
- VIU_OSD_BLEND_CTRL
- OSD1_BLEND_SRC_CTRL
- OSD2_BLEND_SRC_CTRL
- DOLBY_PATH_CTRL
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: fix OSD1_BLEND_SRC_CTRL register init value for G12A]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/86sgrz82em.fsf@baylibre.com
Maarten needs -rc4 backmerged so he can pull in the fbcon notifier
removal topic branch into drm-misc-next.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The G12A Primary plane was disabled by writing in the OSD1 configuration
registers, but this caused the plane blender to stall instead of continuing
to blend only the overlay plane.
Fix this by disabling the OSD1 plane in the blender registers, and also
enabling it back using the same register.
Fixes: 490f50c109 ("drm/meson: Add G12A support for OSD1 Plane")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
[narmstrong: fixed nit in commit log]
Link: https://patchwork.freedesktop.org/patch/msgid/20190605141253.24165-3-narmstrong@baylibre.com
