Pull nios2 update from Ley Foon Tan:
"Mark expected switch fall-through in signal handling"
* tag 'nios2-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
nios2: signal: Mark expected switch fall-through
Mark switch cases where we are expecting to fall through.
Fix the following warning through the use of the new the new
pseudo-keyword fallthrough;
arch/nios2/kernel/signal.c:254:12: warning: this statement may fall through [-Wimplicit-fallthrough=]
254 | restart = -2;
| ~~~~~~~~^~~~
arch/nios2/kernel/signal.c:255:3: note: here
255 | case ERESTARTNOHAND:
| ^~~~
Reported-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Currently, the log-level of show_stack() depends on a platform
realization. It creates situations where the headers are printed with
lower log level or higher than the stacktrace (depending on a platform or
user).
Furthermore, it forces the logic decision from user to an architecture
side. In result, some users as sysrq/kdb/etc are doing tricks with
temporary rising console_loglevel while printing their messages. And in
result it not only may print unwanted messages from other CPUs, but also
omit printing at all in the unlucky case where the printk() was deferred.
Introducing log-level parameter and KERN_UNSUPPRESSED [1] seems an easier
approach than introducing more printk buffers. Also, it will consolidate
printings with headers.
Introduce show_stack_loglvl(), that eventually will substitute
show_stack().
[1]: https://lore.kernel.org/lkml/20190528002412.1625-1-dima@arista.com/T/#u
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Ley Foon Tan <lftan@altera.com>
Link: http://lkml.kernel.org/r/20200418201944.482088-24-dima@arista.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
now that can be done conveniently - all non-trivial cases have
_HAVE_ARCH_COPY_AND_CSUM_FROM_USER defined, so the fallback in
net/checksum.h is used only for dummy (copy_from_user, then
csum_partial) implementation. Allowing us to get rid of all
dummy instances, both of csum_and_copy_from_user() and
csum_partial_copy_from_user().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
There is no more 'altr,gpio-bank-width' in the 'altr,pio-1.0' driver.
There is a 'altr,ngpio' which is what the property wants to configure.
This change updates all occurrences of 'altr,gpio-bank-width' to
'altr,ngpio'.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
This patch adds support for common clock framework on Nios2. Clock
framework is commonly used in many drivers, and this patch makes it
available for the entire architecture, not just on a per-driver basis.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Pull dma-mapping updates from Christoph Hellwig:
- fix an integer overflow in the coherent pool (Kevin Grandemange)
- provide support for in-place uncached remapping and use that for
openrisc
- fix the arm coherent allocator to take the bus limit into account
* tag 'dma-mapping-5.7' of git://git.infradead.org/users/hch/dma-mapping:
ARM/dma-mapping: merge __dma_supported into arm_dma_supported
ARM/dma-mapping: take the bus limit into account in __dma_alloc
ARM/dma-mapping: remove get_coherent_dma_mask
openrisc: use the generic in-place uncached DMA allocator
dma-direct: provide a arch_dma_clear_uncached hook
dma-direct: make uncached_kernel_address more general
dma-direct: consolidate the error handling in dma_direct_alloc_pages
dma-direct: remove the cached_kernel_address hook
dma-coherent: fix integer overflow in the reserved-memory dma allocation
Pull SPDX updates from Greg KH:
"Here are three SPDX patches for 5.7-rc1.
One fixes up the SPDX tag for a single driver, while the other two go
through the tree and add SPDX tags for all of the .gitignore files as
needed.
Nothing too complex, but you will get a merge conflict with your
current tree, that should be trivial to handle (one file modified by
two things, one file deleted.)
All three of these have been in linux-next for a while, with no
reported issues other than the merge conflict"
* tag 'spdx-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx:
ASoC: MT6660: make spdxcheck.py happy
.gitignore: add SPDX License Identifier
.gitignore: remove too obvious comments
The idea comes from a discussion between Linus and Andrea [1].
Before this patch we only allow a page fault to retry once. We achieved
this by clearing the FAULT_FLAG_ALLOW_RETRY flag when doing
handle_mm_fault() the second time. This was majorly used to avoid
unexpected starvation of the system by looping over forever to handle the
page fault on a single page. However that should hardly happen, and after
all for each code path to return a VM_FAULT_RETRY we'll first wait for a
condition (during which time we should possibly yield the cpu) to happen
before VM_FAULT_RETRY is really returned.
This patch removes the restriction by keeping the FAULT_FLAG_ALLOW_RETRY
flag when we receive VM_FAULT_RETRY. It means that the page fault handler
now can retry the page fault for multiple times if necessary without the
need to generate another page fault event. Meanwhile we still keep the
FAULT_FLAG_TRIED flag so page fault handler can still identify whether a
page fault is the first attempt or not.
Then we'll have these combinations of fault flags (only considering
ALLOW_RETRY flag and TRIED flag):
- ALLOW_RETRY and !TRIED: this means the page fault allows to
retry, and this is the first try
- ALLOW_RETRY and TRIED: this means the page fault allows to
retry, and this is not the first try
- !ALLOW_RETRY and !TRIED: this means the page fault does not allow
to retry at all
- !ALLOW_RETRY and TRIED: this is forbidden and should never be used
In existing code we have multiple places that has taken special care of
the first condition above by checking against (fault_flags &
FAULT_FLAG_ALLOW_RETRY). This patch introduces a simple helper to detect
the first retry of a page fault by checking against both (fault_flags &
FAULT_FLAG_ALLOW_RETRY) and !(fault_flag & FAULT_FLAG_TRIED) because now
even the 2nd try will have the ALLOW_RETRY set, then use that helper in
all existing special paths. One example is in __lock_page_or_retry(), now
we'll drop the mmap_sem only in the first attempt of page fault and we'll
keep it in follow up retries, so old locking behavior will be retained.
This will be a nice enhancement for current code [2] at the same time a
supporting material for the future userfaultfd-writeprotect work, since in
that work there will always be an explicit userfault writeprotect retry
for protected pages, and if that cannot resolve the page fault (e.g., when
userfaultfd-writeprotect is used in conjunction with swapped pages) then
we'll possibly need a 3rd retry of the page fault. It might also benefit
other potential users who will have similar requirement like userfault
write-protection.
GUP code is not touched yet and will be covered in follow up patch.
Please read the thread below for more information.
[1] https://lore.kernel.org/lkml/20171102193644.GB22686@redhat.com/
[2] https://lore.kernel.org/lkml/20181230154648.GB9832@redhat.com/
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Suggested-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Brian Geffon <bgeffon@google.com>
Cc: Bobby Powers <bobbypowers@gmail.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Denis Plotnikov <dplotnikov@virtuozzo.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: "Kirill A . Shutemov" <kirill@shutemov.name>
Cc: Martin Cracauer <cracauer@cons.org>
Cc: Marty McFadden <mcfadden8@llnl.gov>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Maya Gokhale <gokhale2@llnl.gov>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Link: http://lkml.kernel.org/r/20200220160246.9790-1-peterx@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change a header to mandatory-y if both of the following are met:
[1] At least one architecture (except um) specifies it as generic-y in
arch/*/include/asm/Kbuild
[2] Every architecture (except um) either has its own implementation
(arch/*/include/asm/*.h) or specifies it as generic-y in
arch/*/include/asm/Kbuild
This commit was generated by the following shell script.
----------------------------------->8-----------------------------------
arches=$(cd arch; ls -1 | sed -e '/Kconfig/d' -e '/um/d')
tmpfile=$(mktemp)
grep "^mandatory-y +=" include/asm-generic/Kbuild > $tmpfile
find arch -path 'arch/*/include/asm/Kbuild' |
xargs sed -n 's/^generic-y += \(.*\)/\1/p' | sort -u |
while read header
do
mandatory=yes
for arch in $arches
do
if ! grep -q "generic-y += $header" arch/$arch/include/asm/Kbuild &&
! [ -f arch/$arch/include/asm/$header ]; then
mandatory=no
break
fi
done
if [ "$mandatory" = yes ]; then
echo "mandatory-y += $header" >> $tmpfile
for arch in $arches
do
sed -i "/generic-y += $header/d" arch/$arch/include/asm/Kbuild
done
fi
done
sed -i '/^mandatory-y +=/d' include/asm-generic/Kbuild
LANG=C sort $tmpfile >> include/asm-generic/Kbuild
----------------------------------->8-----------------------------------
One obvious benefit is the diff stat:
25 files changed, 52 insertions(+), 557 deletions(-)
It is tedious to list generic-y for each arch that needs it.
So, mandatory-y works like a fallback default (by just wrapping
asm-generic one) when arch does not have a specific header
implementation.
See the following commits:
def3f7cefea1b39bae16
It is tedious to convert headers one by one, so I processed by a shell
script.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/20200210175452.5030-1-masahiroy@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename the symbol to arch_dma_set_uncached, and pass a size to it as
well as allow an error return. That will allow reusing this hook for
in-place pagetable remapping.
As the in-place remap doesn't always require an explicit cache flush,
also detangle ARCH_HAS_DMA_PREP_COHERENT from ARCH_HAS_DMA_SET_UNCACHED.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
dma-direct now finds the kernel address for coherent allocations based
on the dma address, so the cached_kernel_address hooks is unused and
can be removed entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Pull tty/serial driver updates from Greg KH:
"Here are the big set of tty and serial driver updates for 5.6-rc1
Included in here are:
- dummy_con cleanups (touches lots of arch code)
- sysrq logic cleanups (touches lots of serial drivers)
- samsung driver fixes (wasn't really being built)
- conmakeshash move to tty subdir out of scripts
- lots of small tty/serial driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: n_hdlc: Use flexible-array member and struct_size() helper
tty: baudrate: SPARC supports few more baud rates
tty: baudrate: Synchronise baud_table[] and baud_bits[]
tty: serial: meson_uart: Add support for kernel debugger
serial: imx: fix a race condition in receive path
serial: 8250_bcm2835aux: Document struct bcm2835aux_data
serial: 8250_bcm2835aux: Use generic remapping code
serial: 8250_bcm2835aux: Allocate uart_8250_port on stack
serial: 8250_bcm2835aux: Suppress register_port error on -EPROBE_DEFER
serial: 8250_bcm2835aux: Suppress clk_get error on -EPROBE_DEFER
serial: 8250_bcm2835aux: Fix line mismatch on driver unbind
serial_core: Remove unused member in uart_port
vt: Correct comment documenting do_take_over_console()
vt: Delete comment referencing non-existent unbind_con_driver()
arch/xtensa/setup: Drop dummy_con initialization
arch/x86/setup: Drop dummy_con initialization
arch/unicore32/setup: Drop dummy_con initialization
arch/sparc/setup: Drop dummy_con initialization
arch/sh/setup: Drop dummy_con initialization
arch/s390/setup: Drop dummy_con initialization
...
Pull scheduler updates from Ingo Molnar:
"These were the main changes in this cycle:
- More -rt motivated separation of CONFIG_PREEMPT and
CONFIG_PREEMPTION.
- Add more low level scheduling topology sanity checks and warnings
to filter out nonsensical topologies that break scheduling.
- Extend uclamp constraints to influence wakeup CPU placement
- Make the RT scheduler more aware of asymmetric topologies and CPU
capacities, via uclamp metrics, if CONFIG_UCLAMP_TASK=y
- Make idle CPU selection more consistent
- Various fixes, smaller cleanups, updates and enhancements - please
see the git log for details"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (58 commits)
sched/fair: Define sched_idle_cpu() only for SMP configurations
sched/topology: Assert non-NUMA topology masks don't (partially) overlap
idle: fix spelling mistake "iterrupts" -> "interrupts"
sched/fair: Remove redundant call to cpufreq_update_util()
sched/psi: create /proc/pressure and /proc/pressure/{io|memory|cpu} only when psi enabled
sched/fair: Fix sgc->{min,max}_capacity calculation for SD_OVERLAP
sched/fair: calculate delta runnable load only when it's needed
sched/cputime: move rq parameter in irqtime_account_process_tick
stop_machine: Make stop_cpus() static
sched/debug: Reset watchdog on all CPUs while processing sysrq-t
sched/core: Fix size of rq::uclamp initialization
sched/uclamp: Fix a bug in propagating uclamp value in new cgroups
sched/fair: Load balance aggressively for SCHED_IDLE CPUs
sched/fair : Improve update_sd_pick_busiest for spare capacity case
watchdog: Remove soft_lockup_hrtimer_cnt and related code
sched/rt: Make RT capacity-aware
sched/fair: Make EAS wakeup placement consider uclamp restrictions
sched/fair: Make task_fits_capacity() consider uclamp restrictions
sched/uclamp: Rename uclamp_util_with() into uclamp_rq_util_with()
sched/uclamp: Make uclamp util helpers use and return UL values
...
Commit 5ace77e0b4 ("nios2: remove __ioremap") removed the following code,
with the argument that cacheflag is always 0 and the expression would
therefore always be false.
if (IS_MAPPABLE_UNCACHEABLE(phys_addr) &&
IS_MAPPABLE_UNCACHEABLE(last_addr) &&
!(cacheflag & _PAGE_CACHED))
return (void __iomem *)(CONFIG_NIOS2_IO_REGION_BASE + phys_addr);
This did not take the "!" in the expression into account. Result is that
nios2 images no longer boot. Restoring the removed code fixes the problem.
Fixes: 5ace77e0b4 ("nios2: remove __ioremap")
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
In the x86 MM code we'd like to untangle various types of historic
header dependency spaghetti, but for this we'd need to pass to
the generic vmalloc code various vmalloc related defines that
customarily come via the <asm/page.h> low level arch header.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull sysctl system call removal from Eric Biederman:
"As far as I can tell we have reached the point where no one enables
the sysctl system call anymore. It still is enabled in a few
defconfigs but they are mostly the rarely used one and in asking
people about that it was more cut & paste enabled than anything else.
This is single commit that just deletes code. Leaving just enough code
so that the deprecated sysctl warning continues to be printed. If my
analysis turns out to be wrong and someone actually cares it will be
easy to revert this commit and have the system call again.
There was one new xtensa defconfig in linux-next that enabled the
system call this cycle and when asked about it the maintainer of the
code replied that it was not enabled on purpose. As of today's
linux-next tree that defconfig no longer enables the system call.
What we saw in the review discussion was that if we go a step farther
than my patch and mess with uapi headers there are pieces of code that
won't compile, but nothing minds the system call actually disappearing
from the kernel"
Link: https://lore.kernel.org/lkml/201910011140.EA0181F13@keescook/
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
sysctl: Remove the sysctl system call
Pull dma-mapping updates from Christoph Hellwig:
- improve dma-debug scalability (Eric Dumazet)
- tiny dma-debug cleanup (Dan Carpenter)
- check for vmap memory in dma_map_single (Kees Cook)
- check for dma_addr_t overflows in dma-direct when using DMA offsets
(Nicolas Saenz Julienne)
- switch the x86 sta2x11 SOC to use more generic DMA code (Nicolas
Saenz Julienne)
- fix arm-nommu dma-ranges handling (Vladimir Murzin)
- use __initdata in CMA (Shyam Saini)
- replace the bus dma mask with a limit (Nicolas Saenz Julienne)
- merge the remapping helpers into the main dma-direct flow (me)
- switch xtensa to the generic dma remap handling (me)
- various cleanups around dma_capable (me)
- remove unused dev arguments to various dma-noncoherent helpers (me)
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux:
* tag 'dma-mapping-5.5' of git://git.infradead.org/users/hch/dma-mapping: (22 commits)
dma-mapping: treat dev->bus_dma_mask as a DMA limit
dma-direct: exclude dma_direct_map_resource from the min_low_pfn check
dma-direct: don't check swiotlb=force in dma_direct_map_resource
dma-debug: clean up put_hash_bucket()
powerpc: remove support for NULL dev in __phys_to_dma / __dma_to_phys
dma-direct: avoid a forward declaration for phys_to_dma
dma-direct: unify the dma_capable definitions
dma-mapping: drop the dev argument to arch_sync_dma_for_*
x86/PCI: sta2x11: use default DMA address translation
dma-direct: check for overflows on 32 bit DMA addresses
dma-debug: increase HASH_SIZE
dma-debug: reorder struct dma_debug_entry fields
xtensa: use the generic uncached segment support
dma-mapping: merge the generic remapping helpers into dma-direct
dma-direct: provide mmap and get_sgtable method overrides
dma-direct: remove the dma_handle argument to __dma_direct_alloc_pages
dma-direct: remove __dma_direct_free_pages
usb: core: Remove redundant vmap checks
kernel: dma-contiguous: mark CMA parameters __initdata/__initconst
dma-debug: add a schedule point in debug_dma_dump_mappings()
...
Pull generic ioremap support from Christoph Hellwig:
"This adds the remaining bits for an entirely generic ioremap and
iounmap to lib/ioremap.c. To facilitate that, it cleans up the giant
mess of weird ioremap variants we had with no users outside the arch
code.
For now just the three newest ports use the code, but there is more
than a handful others that can be converted without too much work.
Summary:
- clean up various obsolete ioremap and iounmap variants
- add a new generic ioremap implementation and switch csky, nds32 and
riscv over to it"
* tag 'ioremap-5.5' of git://git.infradead.org/users/hch/ioremap: (21 commits)
nds32: use generic ioremap
csky: use generic ioremap
csky: remove ioremap_cache
riscv: use the generic ioremap code
lib: provide a simple generic ioremap implementation
sh: remove __iounmap
nios2: remove __iounmap
hexagon: remove __iounmap
m68k: rename __iounmap and mark it static
arch: rely on asm-generic/io.h for default ioremap_* definitions
asm-generic: don't provide ioremap for CONFIG_MMU
asm-generic: ioremap_uc should behave the same with and without MMU
xtensa: clean up ioremap
x86: Clean up ioremap()
parisc: remove __ioremap
nios2: remove __ioremap
alpha: remove the unused __ioremap wrapper
hexagon: clean up ioremap
ia64: rename ioremap_nocache to ioremap_uc
unicore32: remove ioremap_cached
...
These are pure cache maintainance routines, so drop the unused
struct device argument.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Various architectures that use asm-generic/io.h still defined their
own default versions of ioremap_nocache, ioremap_wt and ioremap_wc
that point back to plain ioremap directly or indirectly. Remove these
definitions and rely on asm-generic/io.h instead. For this to work
the backup ioremap_* defintions needs to be changed to purely cpp
macros instea of inlines to cover for architectures like openrisc
that only define ioremap after including <asm-generic/io.h>.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Palmer Dabbelt <palmer@dabbelt.com>
Pull nios2 fix from Ley Foon Tan:
"Make sure the command line buffer is NUL-terminated"
* tag 'nios2-v5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
nios2: force the string buffer NULL-terminated
The naming of pgtable_page_{ctor,dtor}() seems to have confused a few
people, and until recently arm64 used these erroneously/pointlessly for
other levels of page table.
To make it incredibly clear that these only apply to the PTE level, and to
align with the naming of pgtable_pmd_page_{ctor,dtor}(), let's rename them
to pgtable_pte_page_{ctor,dtor}().
These changes were generated with the following shell script:
----
git grep -lw 'pgtable_page_.tor' | while read FILE; do
sed -i '{s/pgtable_page_ctor/pgtable_pte_page_ctor/}' $FILE;
sed -i '{s/pgtable_page_dtor/pgtable_pte_page_dtor/}' $FILE;
done
----
... with the documentation re-flowed to remain under 80 columns, and
whitespace fixed up in macros to keep backslashes aligned.
There should be no functional change as a result of this patch.
Link: http://lkml.kernel.org/r/20190722141133.3116-1-mark.rutland@arm.com
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Yu Zhao <yuzhao@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both pgtable_cache_init() and pgd_cache_init() are used to initialize kmem
cache for page table allocations on several architectures that do not use
PAGE_SIZE tables for one or more levels of the page table hierarchy.
Most architectures do not implement these functions and use __weak default
NOP implementation of pgd_cache_init(). Since there is no such default
for pgtable_cache_init(), its empty stub is duplicated among most
architectures.
Rename the definitions of pgd_cache_init() to pgtable_cache_init() and
drop empty stubs of pgtable_cache_init().
Link: http://lkml.kernel.org/r/1566457046-22637-1-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Will Deacon <will@kernel.org> [arm64]
Acked-by: Thomas Gleixner <tglx@linutronix.de> [x86]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
