Small fixes to make these DTs compliant with the adi,adv7511w and
adi,adv7513 bindings:
r8a7745-iwg22d-sodimm-dbhd-ca.dts
r8a7790-lager.dts
r8a7790-stout.dts
r8a7791-koelsch.dts
r8a7791-porter.dts
r8a7792-blanche.dts
r8a7793-gose.dts
r8a7794-silk.dts:
Remove the adi,input-style and adi,input-justification properties.
r8a7792-wheat.dts:
Reorder the I2C slave addresses of hdmi@3d and hdmi@39 and remove
the adi,input-style and adi,input-justification properties.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200511110611.3142-3-ricardo.canuelo@collabora.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
IoT Box is an IoT gateway device based on Stinger96 board powered by
STM32MP1 SoC, designed and manufactured by Shiratech Solutions. This
device makes use of Stinger96 board by having it as a base board with
one additional mezzanine on top.
Following are the features exposed by this device in addition to the
Stinger96 board:
* WiFi/BT
* CCS811 VOC sensor
* 2x Digital microphones IM69D130
* 12x WS2812B LEDs
Following peripherals are tested and known to work:
* WiFi/BT
* CCS811
More information about this device can be found in Shiratech website:
https://www.shiratech-solutions.com/products/iot-box/
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Stinger96 is a 96Boards IoT Extended edition board designed and
manufactured by Shiratech solutions based on STM32MP1 SoC. Following
are the features of this board:
* 256MB DDR
* 125MB NAND Flash
* Onboard BG96 modem
* 1x uSD
* 2x USB (1 available as external connector and another connected to BG96)
* 1x SPI
* 1x PCM
* 2x UART (apart from serial console)
* 2x I2C (apart from one connected to PMIC)
Following peripherals are tested and known to work:
* BG96 modem
* 1x I2C (LS-I2C0)
* 1x SPI
* 1x UART (LS-UART0)
* USB (Only Gadget mode)
* uSD
More information about this board can be found in Shiratech website:
https://www.shiratech-solutions.com/products/stinger96/
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
These pinctrl definitions will be used by Stinger96/IoTBox boards
from Shiratech.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Fixes for omaps for v5.6-rc cycle
Few device tree fixes for various devices:
- A regression fix for non-existing can device on am534x-idk
- Fix missing dma-ranges for dra7 pcie
- Fix flakey wlan on droid4 where some devices would not connect
at all because of internal pull being used with an external pull
- Fix occasional missed wake-up events on droid4 modem uart
* tag 'omap-for-v5.6/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-droid4: Fix occasional lost wakeirq for uart1
ARM: dts: omap4-droid4: Fix flakey wlan by disabling internal pull for gpio
ARM: dts: dra7: Fix bus_dma_limit for PCIe
ARM: dts: am574x-idk: Disable m_can node
Link: https://lore.kernel.org/r/pull-1588872844-804667@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some fixes for the newly added Pinebook Pro and other fixes to
make dtc and the new dtscheck against yaml bindings happy.
* tag 'v5.7-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: fix pinctrl sub nodename for spi in rk322x.dtsi
arm64: dts: rockchip: Fix Pinebook Pro FUSB302 interrupt
ARM: dts: rockchip: swap clock-names of gpu nodes
arm64: dts: rockchip: swap interrupts interrupt-names rk3399 gpu node
arm64: dts: rockchip: fix status for &gmac2phy in rk3328-evb.dts
arm64: dts: rockchip: remove extra assigned-clocks property from &gmac2phy node in rk3328-evb.dts
ARM: dts: rockchip: fix phy nodename for rk3229-xms6
ARM: dts: rockchip: fix phy nodename for rk3228-evb
arm64: dts: rockchip: Rename dwc3 device nodes on rk3399 to make dtc happy
arm64: dts: rockchip: drop #address-cells, #size-cells from rk3399 pmugrf node
arm64: dts: rockchip: drop #address-cells, #size-cells from rk3328 grf node
arm64: dts: rockchip: drop non-existent gmac2phy pinmux options from rk3328
arm64: dts: rockchip: Replace RK805 PMIC node name with "pmic" on rk3328 boards
arm64: dts: rockchip: enable DC charger detection pullup on Pinebook Pro
arm64: dts: rockchip: fix inverted headphone detection on Pinebook Pro
arm64: dts: rockchip: Correct PMU compatibles for PX30 and RK3308
Link: https://lore.kernel.org/r/1738941.6LdaBJIBqS@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Renesas fixes for v5.7
- Fix IOMMU support on R-Car V3H,
- Minor fixes that are fast-tracked to avoid introducing regressions
during conversion of DT bindings to json-schema.
* tag 'renesas-fixes-for-v5.7-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: dts: r7s9210: Remove bogus clock-names from OSTM nodes
arm64: dts: renesas: r8a77980: Fix IPMMU VIP[01] nodes
ARM: dts: r8a73a4: Add missing CMT1 interrupts
Link: https://lore.kernel.org/r/20200430084834.1384-1-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX fixes for 5.7:
- Set correct AHB clock for i.MX8MN SDMA1 device to fix a "Timeout
waiting for CH0" error.
- Fix a linker error for i.MX6 configurations that have ARM_CPU_SUSPEND=n,
which can happen if neither CONFIG_PM, CONFIG_CPU_IDLE, nor ARM_PSCI_FW
are selected.
- Fix I2C1 pinctrl configuration for i.MX27 phytec-phycard board.
- Fix i.MX8M AIPS 'reg' properties to remove DTC simple_bus_reg
warnings.
- Add missing compatible "fsl,vf610-edma" for LS1028A EDMA device, so
that bootloader can fix up the IOMMU entries there. Otherwise, EDMA
just doesn't work on LS1028A with shipped bootloader.
- Fix imx6dl-yapp4-ursa board Ethernet connection.
- Fix input_val for AUDIOMIX_BIT_STREAM pinctrl defines on i.MX8MP
according to Reference Manual.
* tag 'imx-fixes-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: freescale: imx8mp: update input_val for AUDIOMIX_BIT_STREAM
arm64: dts: imx8m: Fix AIPS reg properties
arm64: dts: imx8mn: Change SDMA1 ahb clock for imx8mn
ARM: dts: imx27-phytec-phycard-s-rdk: Fix the I2C1 pinctrl entries
ARM: imx: provide v7_cpu_resume() only on ARM_CPU_SUSPEND=y
ARM: dts: imx6dl-yapp4: Fix Ursa board Ethernet connection
arm64: dts: ls1028a: add "fsl,vf610-edma" compatible
dt-bindings: dma: fsl-edma: fix ls1028a-edma compatible
Link: https://lore.kernel.org/r/20200429063226.GT32592@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The GW552x-B board revision adds USB OTG support.
Enable the device-tree node and configure the OTG_ID pin.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Recent PTP-specific cpsw driver changes started exposing an issue on at
at least j5eco-evm:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xf0169004
...
(davinci_mdio_runtime_suspend) from [<c063f2a4>] (__rpm_callback+0x84/0x154)
(__rpm_callback) from [<c063f394>] (rpm_callback+0x20/0x80)
(rpm_callback) from [<c063f4f0>] (rpm_suspend+0xfc/0x6ac)
(rpm_suspend) from [<c0640af0>] (pm_runtime_work+0x88/0xa4)
(pm_runtime_work) from [<c0155338>] (process_one_work+0x228/0x568)
...
Let's fix the issue by using the correct mdio clock as suggested by
Grygorii Strashko <grygorii.strashko@ti.com>.
The DM814_ETHERNET_CPGMAC0_CLKCTRL clock is the interconnect target module
clock and managed by ti-sysc.
Fixes: 6398f3478e ("ARM: dts: Configure interconnect target module for dm814x cpsw")
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Clock Pulse Generator (CPG) device node lacks the extal2 clock.
This may lead to a failure registering the "r" clock, or to a wrong
parent for the "usb24s" clock, depending on MD_CK2 pin configuration and
boot loader CPG_USBCKCR register configuration.
This went unnoticed, as this does not affect the single upstream board
configuration, which relies on the first clock input only.
Fixes: d9ffd583bf ("ARM: shmobile: r8a7740: add SoC clocks to DTS")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20200508095918.6061-1-geert+renesas@glider.be
Since commit bcf3440c6d ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY") the networking is broken on boards:
am437x-gp-evm
am437x-sk-evm
am437x-idk-evm
All above boards have phy-mode = "rgmii" and this is worked before, because
KSZ9031 PHY started with default RGMII internal delays configuration (TX
off, RX on 1.2 ns) and MAC provided TX delay. After above commit, the
KSZ9031 PHY starts handling phy mode properly and disables RX delay, as
result networking is become broken.
Fix it by switching to phy-mode = "rgmii-rxid" to reflect previous
behavior.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since commit bcf3440c6d ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY") the networking is broken on boards:
am571x-idk
am572x-idk
am574x-idk
am57xx-beagle-x15
All above boards have phy-mode = "rgmii" and this is worked before because
KSZ9031 PHY started with default RGMII internal delays configuration (TX
off, RX on 1.2 ns) and MAC provided TX delay. After above commit, the
KSZ9031 PHY starts handling phy mode properly and disables RX delay, as
result networking is become broken.
Fix it by switching to phy-mode = "rgmii-rxid" to reflect previous
behavior.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Declare PSCI v1.0 support instead of v0.1 as the former is supported
by the PSCI firmware stacks stm32mp15x relies on.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Utilize common Tegra30 CPU OPP table. CPU DVFS is available now on beaver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Set min/max voltage and couple CPU/CORE regulators.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
OMAP5 contains a single DES crypto accelerator instance. Add node for
this in DT to enable it.
We keep the node disabled for now, as it appears OMAP5 platform is
running out of available DMA channels, and DES is the least interesting
crypto accelerator available on the device.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the single available SHA crypto accelerator device for OMAP5 SoC.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP5 has AES hardware cryptographic accelerator, add AES2 instance for
it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP5 has AES hardware cryptographic accelerator, add AES1 instance for
it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The watchdog timer information has been added to all the IPU and DSP
remote processor device nodes in the DRA7xx/AM57xx SoC families. The
data has been added to the two common dra7-ipu-dsp-common and
dra74-ipu-dsp-common dtsi files that can be included by all the
desired board files. The following timers are chosen as the watchdog
timers, as per the usage on the current firmware images:
IPU2: GPTimers 4 & 9 (one for each Cortex-M4 core)
IPU1: GPTimers 7 & 8 (one for each Cortex-M4 core)
DSP1: GPTimer 10
DSP2: GPTimer 13
Each of the IPUs has two Cortex-M4 processors and so uses a timer
each for providing watchdog support on that processor irrespective of
whether the IPU is running in SMP-mode or non-SMP node. The chosen
timers also need to be unique from the ones used by other processors
(regular timers or watchdog timers) so that they can be supported
simultaneously.
The MPU-side drivers will use this data to initialize the watchdog
timer(s), and listen for any watchdog triggers. The BIOS-side code on
these processors needs to configure/refresh the corresponding timer
properly to not throw a watchdog error.
The watchdog timers are optional in general, but are mandatory to
be added to support watchdog error recovery on a particular processor.
These timers can be changed or removed as per the system integration
needs, alongside appropriate equivalent changes on the firmware side.
Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for both the IPUs and the
DSP1 remoteproc devices on the AM571x IDK board. These nodes are assigned
to the respective rproc device nodes, and both the IPUs and the DSP1
remote processors are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on the
DRA72 EVM board to maintain firmware compatibility between the two boards.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for all the IPU and DSP
remoteproc devices in the am572x-idk-common.dtsi file that is common to
both the AM572x and AM574x IDK boards. These nodes are assigned to the
respective rproc device nodes, and all the IPU and DSP remote processors
are enabled.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on
the AM57xx EVM board to maintain firmware compatibility between the
two boards. The CMA pools and sizes are defined using 64-bit values
to support LPAE. The starting addresses are fixed to meet current
dependencies on the remote processor firmwares, and this will go
away when the remote-side code has been improved to gather this
information runtime during its initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for all the IPU and DSP
remoteproc devices on all the AM57xx BeagleBoard-X15 boards. These nodes
are assigned to the respective rproc device nodes, and all the IPU and
DSP remote processors are enabled for all these boards.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on the
DRA7 EVM board to maintain firmware compatibility between the two boards.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for all the IPU and
the DSP remoteproc devices on the DRA76 EVM board, and assigned to
the respective rproc device nodes. These match the configuration
used on the DRA7 EVM board. Both the CMA nodes and the corresponding
rproc nodes are also enabled to enable these processors on the
DRA76 EVM board.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for both the IPUs and the
DSP1 remoteproc devices on DRA71 EVM board. These nodes are assigned to
the respective rproc device nodes, and both the IPUs and the DSP1 remote
processors are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on the
DRA72 EVM board to maintain firmware compatibility between the two boards.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for both the IPUs and
the DSP1 remoteproc devices on the DRA72 EVM rev C board, and assigned
to the respective rproc device nodes. These match the configuration
used on the DRA72 EVM board. Both the CMA nodes and the corresponding
rproc nodes are also enabled to enable these processors on the
DRA72 EVM rev C board.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for both the IPUs and the
DSP1 remoteproc devices on DRA72 EVM board. These nodes are assigned to
the respective rproc device nodes, and both the IPUs and the DSP1 remote
processors are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on the
DRA7 EVM board to maintain firmware compatibility between the two boards.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for all the IPU and DSP
remoteproc devices on DRA7 EVM board. These nodes are assigned to the
respective rproc device nodes, and all the IPU and DSP remote processors
are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The BIOS System Tick timers have been added for all the IPU and
DSP remoteproc devices in the DRA7 SoC family. The data is added
to the two common dra7-ipu-dsp-common and dra74-ipu-dsp-common
dtsi files that are included by all the desired board files. The
following timers are chosen, as per the timers used on the current
firmware images:
IPU2: GPTimer 3
IPU1: GPTimer 11
DSP1: GPTimer 5
DSP2: GPTimer 6
The timers are optional, but are mandatory to support advanced device
management features such as power management and watchdog support.
The above are added to successfully boot and execute firmware images
configured with the respective timers, images that use internal
processor subsystem timers are not affected. The timers can be
changed or removed as per the system integration needs, if needed.
Each of the IPUs has two Cortex-M4 processors, and is currently
expected to be running in SMP-mode, so only a single timer suffices
to provide the BIOS tick timer. An additional timer should be added
for the second processor in IPU if it were to be run in non-SMP mode.
The timer value also needs to be unique from the ones used by other
processors so that they can be run simultaneously.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the required 'mboxes' property to all the IPU and DSP remote
processors (IPU1, IPU2, DSP1 and DSP2) in the two available common
dtsi files - dra7-ipu-dsp-common and dra74-ipu-dsp-common dtsi files.
The latter file is for platforms having DRA74x/DRA76x/AM572x/AM574x
SoCs which do have a DSP2 processor in addition to the other common
remote processors. The common data is added to the former file, and
the DSP2 only data is added to the latter file.
The mailboxes are required for running the Remote Processor Messaging
(RPMsg) stack between the host processor and each of the remote
processors. Each of the remote processors uses a single sub-mailbox
node, the IPUs are assumed to be running in SMP-mode. The chosen
sub-mailboxes match the values used in the current firmware images.
This can be changed, if needed, as per the system integration needs
after making appropriate changes on the firmware side as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
