The checks already prevents periodic cal from being started while noise
floor calibration runs. It is missing checks for the other way around.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AR9002 code and the QCA AR9003+ reference code do the same.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath6kl_bmi_init() is never called in atomic context.
It calls kzalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The QCA4019 hw1.0 firmware 10.4-3.2.1-00050 and 10.4-3.5.3-00053 (and most
likely all other) seem to ignore the WMI_CHAN_FLAG_DFS flag during the
scan. This results in transmission (probe requests) on channels which are
not "available" for transmissions.
Since the firmware is closed source and nothing can be done from our side
to fix the problem in it, the driver has to work around this problem. The
WMI_CHAN_FLAG_PASSIVE seems to be interpreted by the firmware to not
scan actively on a channel unless an AP was detected on it. Simple probe
requests will then be transmitted by the STA on the channel.
ath10k must therefore also use this flag when it queues a radar channel for
scanning. This should reduce the chance of an active scan when the channel
might be "unusable" for transmissions.
Fixes: e8a50f8ba4 ("ath10k: introduce DFS implementation")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These were recently introduced and found by checkpatch:
drivers/net/wireless/ath/ath10k/mac.c:6118: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/mac.c:6121: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/mac.c:6124: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Only rt2800 subdriver of rt2x00 implement sta_add() and sta_remove(),
rt2x00mac_sta_add and rt2x00mac_sta_remove has no callers after
commit 9c87758cf0 ("rt2x00: call sta_add/remove directly in rt2800").
So can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtl8225se_rf_init() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This patch only replaces the mdelay() that has >20ms time to wait.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
probe_atmel_card() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When receiving a beacon or probe response, we should update the
boottime_ns field which is the timestamp the frame was received at.
(cf mac80211.h)
This fixes a scanning issue with Android since it relies on this
timestamp to determine when the AP has been seen for the last time
(via the nl80211 BSS_LAST_SEEN_BOOTTIME parameter).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wl1271_warning() already appends a \n to the format,
so adding one to the warning string gives empty lines in the log.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some features supported by firmware aren't advertised and there is no
way for a driver to query them. This includes e.g. monitor mode details.
Most firmwares support monitor interface but only the latest ones
/announce/ it with a "monitor" flag in the "cap" iovar. There isn't any
reliable detection method for older firmwares (BRCMF_C_MONITOR was tried
but "it only indicates the core part of the stack supports").
Similarly support for tagging monitor frames and building radiotap
headers can't be reliably detected for all firmwares.
This commit adds table that allows mapping features to firmware version.
It adds mappings for 43602a1 and 4366b1 firmwares from
linux-firmware.git. Both were confirmed to be passing monitor frames.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When CONFIG_PROC_FS isn't set, gcc warning this:
drivers/net/wireless/intersil/hostap/hostap_hw.c:2901:12: warning: ‘prism2_registers_proc_show’ defined but not used [-Wunused-function]
static int prism2_registers_proc_show(struct seq_file *m, void *v)
drivers/net/wireless/intersil/hostap/hostap_proc.c:16:12: warning: ‘prism2_debug_proc_show’ defined but not used [-Wunused-function]
static int prism2_debug_proc_show(struct seq_file *m, void *v)
^
drivers/net/wireless/intersil/hostap/hostap_proc.c:49:12: warning: ‘prism2_stats_proc_show’ defined but not used [-Wunused-function]
static int prism2_stats_proc_show(struct seq_file *m, void *v)
^
drivers/net/wireless/intersil/hostap/hostap_proc.c:177:12: warning: ‘prism2_crypt_proc_show’ defined but not used [-Wunused-function]
static int prism2_crypt_proc_show(struct seq_file *m, void *v)
^
fix this by adding #ifdef around them.
hfa384x_read_reg is only used by prism2_registers_proc_show,so move it
into #ifdef.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When CONFIG_PROC_FS isn't set, gcc warning this:
drivers/net/wireless/atmel/atmel.c:1402:12: warning: ‘atmel_proc_show’ defined but not used [-Wunused-function]
static int atmel_proc_show(struct seq_file *m, void *v)
^
fix this by adding #ifdef around it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pointer 'p' is being assigned but is never used hence it is
redundant and can be removed. Also re-work if statement to remove
redundant assignment of p.
Cleans up clang warning:
warning: variable 'p' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variables id, unicast, write, conf, a_band, accum_tx and ucode are
assigned a value but it is never read, hence they are redundant and
can be removed.
Cleans up clang warnings:
warning: variable 'id' set but not used [-Wunused-but-set-variable]
warning: variable 'unicast' set but not used [-Wunused-but-set-variable]
warning: variable 'write' set but not used [-Wunused-but-set-variable]
warning: variable 'conf' set but not used [-Wunused-but-set-variable]
warning: variable 'a_band' set but not used [-Wunused-but-set-variable]
warning: variable 'tx' set but not used [-Wunused-but-set-variable]
warning: variable 'accum_tx' set but not used [-Wunused-but-set-variable]
warning: variable 'ucode' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variables len, ret, reason and crypt are assigned values that
are never read, hence they are redundant and can be removed.
Note: For the variable ret, a return code is being assigned, but
this is not returned and 0 is currently being returned, I believe
this is OK.
Cleans up clang warnings:
warning: variable 'len' set but not used [-Wunused-but-set-variable]
variable 'ret' set but not used [-Wunused-but-set-variable]
warning: variable 'reason' set but not used [-Wunused-but-set-variable]
warning: variable 'crypt' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variables len and dev assigned values but are never used hence they
are redundant and can be removed. Also add in white space in for-loop
and remove some { } braces on if statement.
Cleans up clang warnings:
warning: variable 'len' set but not used [-Wunused-but-set-variable]
warning: variable 'dev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, RSI_NEEDED_HEADROOM is '80' for rsi driver, which is wrong.
As per rsi internal frame format, the RSI_NEEDED_HEADROOM shall be '84',
which is 64(dword_align) + 4(extended_desc) + 16(frame_desc).
Hence, corrected the needed headroom.
Signed-off-by: Amol Hanwate <amol.hanwate@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, AP mode will work on only WLAN alone firmware. To give support
for AP and BT dual mode, adding firmware entry in 'struct ta_metadata'.
The firmware entry is based on what coex_mode is used in driver and coex
mode '4' for all AP+BT related functionalities. Hence, added the same.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
while cleaning up the driver, observed that flash_content pointer is not
necessary in rsi_load_firmware(). Instead of this, driver can use
'fw_entry->data' directly.Hence, removed redundant flash_content pointer.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Removing redundant device id's from both usb and sdio idtables, as rsi
driver currently supporting only one module(RS9113). Also, replaced ids
with specific defines.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to multiple calls of add interface routine, vif is getting duplicated
and at certain instance, we are out of vifs, causing the driver to behave
abnormal.
Fix: Every vif has a unique mac-id, when we got a vif with same mac-id as
the previous id's, we will override the respective vif.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
System is unable to wake-up through magic-packet in secured connections.
Because key descriptor is getting corrupted and firmware is unable to
decrypt the magic packet. Fixed the issue by properly preparing it
before sending it to firmware.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Radio capabilities packet is not prepared properly for 40MHZ case,
ppe_ack_rate is a two byte variable which is initialized wrongly,
hence we are unable to connect, resolved by assigning it properly.
Signed-off-by: Ganapathi Raju <ganapathi.kondraju@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
observed low throughput rates during verification. This is because, QoS
enable flag is overridden by sequence number in the data descriptor frame.
Hence, added the fix for same.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mwifiex firmware inserts only Microsoft information element
Allow other vendor specific IEs to pass from userspace
Signed-off-by: Roman Stratiienko <roman.stratiienko@globallogic.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver is using boolean variables to maintain vairous status
information of adapter. These status variables are accessed by
multiple threads and there is a possibility of a race. To avoid
this, convert these variables to a set of bitops flags, to be
operated atomically.
Below variables of mwifiex_adapter are converted to bitop flags:
surprise_removed
is_cmd_timedout
is_suspended
is_hs_configured
hs_enabling
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver must ensure that whenever it holds a pointer to the list
entry mwifiex_rx_reorder_tbl, it must protect the same with
rx_reorder_tbl_lock. At present there are many places where
driver does not ensure this. To cover all cases, spinlocks in
below funcions are moved out and made sure that the caller will
hold the spinlock:
mwifiex_11n_dispatch_pkt_until_start_win()
mwifiex_11n_scan_and_dispatch()
mwifiex_del_rx_reorder_entry()
mwifiex_11n_get_rx_reorder_tbl()
mwifiex_11n_find_last_seq_num()
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
At present driver spinlock protects iteration of list
rx_reorder_tbl_ptr with rx_reorder_tbl_lock. To protect the
individual items in this list, it uses rx_pkt_lock. But, we can
use a single rx_reorder_tbl_lock for both purposes. This patch
replaces rx_pkt_lock by rx_reorder_tbl_lock.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Debugfs support to do hardware warm reset with WMI command
WMI_PDEV_PARAM_PDEV_RESET for 10.4 and 10.2.4(if wmi
service is enabled in the firmware for backward compatibility).
This change is purely for debugging purpose when hardware hangs/mutes.
This hardware reset won't affect the connectivity but there will be small
pause in data traffic. Here we are doing BB/MAC level reset and hence
whenever the BB/MAC watchdog is triggered, it does a hardware_chip_reset.
So the target will be in the active state.
Below command used to warm reset the hardware.
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/warm_hw_reset
Tested in QCA988X with firmware ver 10.2.4.70.45
Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00011
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is only code refactoring as all call sites of
ath10k_htt_tx_alloc_msdu_id() take the same lock it can be moved into the
id_get function and the assertion dropped.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variables netlen, orig_buf, orig_len, dropped and stats are assigned values
but are never used hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'netlen' set but not used [-Wunused-but-set-variable]
warning: variable 'orig_buf' set but not used [-Wunused-but-set-variable]
warning: variable 'orig_len' set but not used [-Wunused-but-set-variable]
warning: variable 'dropped' set but not used [-Wunused-but-set-variable]
warning: variable 'stats' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pointer rf is being assigned but is never used hence it is redundant
and can be removed.
Cleans up two clang warnings:
warning: variable 'rf' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pointers dev and noa are being assigned but are never used hence they
are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'dev' set but not used [-Wunused-but-set-variable]
warning: variable 'noa' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 transmits management frames via WMI
with reference. Currently, with the management
tx completion not being handled, these frames are
not getting freed even after the transmission status
is returned by the firmware.
The transmitted management frames should be freed
when the firmware sends the over-the-air tx status of
the corresponding management frames.
Handle the wmi mgmt tx completion event and free
the corresponding management frame.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The tx completion of multiple mgmt frames can be bundled
in a single event and sent by the firmware to host, if this
capability is not disabled explicitly by the host. If the host
cannot handle the bundled mgmt tx completion, this capability
support needs to be disabled in the wmi init cmd, sent to the firmware.
Add the host capability indication flag in the wmi ready command,
to let firmware know the features supported by the host driver.
This field is ignored if it is not supported by firmware.
Set the host capability indication flag(i.e. host_capab) to zero,
for disabling the support of bundle mgmt tx completion. This will
indicate the firmware to send completion event for every mgmt tx
completion, instead of bundling them together and sending in a single
event.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Issues a wmi command to firmware when multicast rate change is received with the
new BSS_CHANGED_MCAST_RATE flag. Also fixes the incorrect fixed_rate setting
for CCK rates which got introduced with addition of ath10k_rates_rev2 enum.
Tested on QCA9984 with firmware ver 10.4-3.6-00104
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes a recently added checkpatch warning:
wmi-tlv.c:2703: open brace '{' following function definitions go on the next line
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce mac80211 rts threshold handler in order to add frame
protection support to mt76x2 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fall back to software encryption for hw unsupported ciphers in order
to enable 802.11w
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable support for multiple SSIDs scans. Get max number of supported
SSIDs from firmware and report to cfg80211 core.
Signed-off-by: Andrey Shevchenko <ashevchenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement set_power_mgmt() callback that forwards power saving
settings to the device firmware.
Signed-off-by: Sergei Maksimenko <smaksimenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The smallest rb size supported today is 4k rx buffers.
22560 devices use 2k rxb's, so allow using 2k buffers.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In 22560 devices the firmware will do all the hw configurations,
but that's not ready yet.
Update the correct registers in the driver until the FW is ready
and does it by itself.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
22560 devices RFH uses different structures, which act similar
to the legacy rxq management lists - free and used list.
The iwl_rx_transfer_desc struct is part of the free list,
and consists of pointers to the empty rb's the driver wants to
pass to the fw.
The iwl_rx_completion_desc struct is part of the used list,
and consists of pointers to the buffer the fw filled up
with new rx, both commands and data, for the host.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
